Reference Stress Based Approach to Predict Failure Strength of Pipes With Local Wall Thinning Under Combined Loading

2005 ◽  
Vol 127 (1) ◽  
pp. 76-83 ◽  
Author(s):  
Do-Jun Shim ◽  
Young-Jin Kim ◽  
Yun-Jae Kim
Keyword(s):  
Internal Pressure ◽  
Equivalent Stress ◽  
New Method ◽  
Combined Loading ◽  
Failure Strength ◽  
Creep Stress ◽  
Reference Stress ◽  
Wall Thinning ◽  
Good Agreement ◽  
Local Wall Thinning

In the previous work carried out by the authors, a new method to estimate failure strength of a pipe with local wall thinning subject to either internal pressure or global bending has been proposed. The proposed method was based on the equivalent stress averaged over the minimum ligament in the locally wall thinned region, and the simple scheme to estimate the equivalent stress in the minimum ligament was proposed, based on the reference stress concept for creep stress analysis. This paper extends the new method to combined internal pressure and global bending. The proposed method is validated against FE results for various geometries of local wall thinning under combined loading. The effect of internal pressure is also investigated in the present study. Comparison of maximum moments, predicted according to the proposed method, with published full-scale pipe test data for locally wall thinned pipes under combined internal pressure and global bending, shows good agreement.

Reference Stress Based Approach to Predict Failure Strength of Pipes With Local Wall Thinning Under Single Loading

2004 ◽  
Vol 126 (2) ◽  
pp. 194-201 ◽  
Author(s):  
Yun-Jae Kim ◽  
Do-Jun Shim ◽  
Hwan Lim ◽  
Young-Jin Kim
Keyword(s):  
Equivalent Stress ◽  
Three Dimensional ◽  
Failure Strength ◽  
Creep Stress ◽  
Estimation Equations ◽  
Reference Stress ◽  
Wall Thinning ◽  
Approximate Estimation ◽  
Failure Loads ◽  
Local Wall Thinning

This paper proposes a new method to estimate failure strength of a pipe with local wall thinning. The method is based on the equivalent stress averaged over the minimum ligament in the locally wall thinned region. The highlight of the proposed method is to propose a simple scheme to estimate the equivalent stress in the minimum ligament. Inspired by the reference stress method for approximate creep stress analysis, approximate estimation equations are proposed for the equivalent stress in the minimum ligament, which are then calibrated using detailed elastic-plastic three-dimensional FE analysis. Remarkably the resulting estimation equations are found to be insensitive not only to pipe and defect geometries but also to material. Comparison of failure loads, predicted according to the proposed method, with published test data for corroded pipes shows excellent agreement, which provides confidence in the use of the proposed method to assess local wall thinning in pipes. Furthermore, the proposed method is conceptually simple and thus easy to be extended to more complex situations.

Reference Stress Approach for Failure Strength Estimates of a Pipe With Local Wall Thinning

2005 ◽  
Author(s):  
Yun-Jae Kim ◽  
Young-Jin Kim
Keyword(s):  
Equivalent Stress ◽  
Fe Analysis ◽  
Creep Stress ◽  
Estimation Equations ◽  
Reference Stress ◽  
Wall Thinning ◽  
Approximate Estimation ◽  
Failure Loads ◽  
Reference Stress Approach ◽  
Local Wall Thinning

This paper proposes a method based on the reference stress a approach to estimate residual strength of a pipe with local wall thinning. The method is based on the equivalent stress averaged over the minimum ligament in the locally wall thinned region. Inspired by the reference stress method for approximate creep stress analysis, approximate estimation equations for the equivalent stress in the minimum ligament are proposed, which are then calibrated using detailed elastic-plastic 3-D FE analysis. The resulting estimation equations are found to be insensitive not only to pipe and defect geometries but also to material. Comparison of failure loads, predicted according to the proposed method, with published test data for corroded pipes shows excellent agreement.

Failure Strength Assessment of Pipes With Local Wall Thinning Under Combined Loading Based on Finite Element Analyses

2004 ◽  
Vol 126 (2) ◽  
pp. 179-183 ◽  
Author(s):  
Do-Jun Shim ◽  
Jae-Boong Choi ◽  
Young-Jin Kim
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Nuclear Power ◽  
Bending Moment ◽  
Combined Loading ◽  
Assessment Procedure ◽  
Finite Element Analyses ◽  
Maximum Moment ◽  
Wall Thinning ◽  
Local Wall Thinning

Failure assessment of a pipe with local wall thinning draws increasing attention in the nuclear power plant industry. Although many guidelines have been developed and are used for assessing the integrity of a wall-thinned pipeline, most of these guidelines consider only pressure loading and thus neglect bending loading. As most pipelines in nuclear power plants are subjected to internal pressure and bending moment, an assessment procedure for locally wall-thinned pipeline subjected to combined loading is urgently needed. In this paper, three-dimensional finite element (FE) analyses are carried out to simulate full-scale pipe tests conducted for various shapes of wall-thinned area under internal pressure and bending moment. Maximum moments based on ultimate tensile stress were obtained from FE results to predict the failure of the pipe. These results are compared with test results, showing good agreement. Additional finite element analyses are then performed to investigate the effect of key parameters, such as wall-thinned depth, wall-thinned angle and wall-thinned length, on maximum moment. Moreover, the effect of internal pressure on maximum moment was investigated. Change of internal pressure did not show significant effect on the maximum moment.

Creep Stress Analyses Affected by Load Properties on P91 Pipe with Local Wall Thinning under High Temperature

2011 ◽  
Vol 704-705 ◽  
pp. 1304-1309
Author(s):  
Ji Lin Xue ◽  
Chang Yu Zhou ◽  
Jian Peng
Keyword(s):  
High Temperature ◽  
Internal Pressure ◽  
Creep Strain ◽  
Power Plants ◽  
Creep Condition ◽  
Stress Redistribution ◽  
Stress And Strain ◽  
Creep Stress ◽  
Wall Thinning ◽  
Local Wall Thinning

The local wall thinning defect is very normal on pipes in power plants, which may result in stress redistribution of the pipes during the service process at elevated temperature. For the purpose of understanding the stress redistribution and strain accumulation of pipes with local wall thinning affected by load properties under creep condition, three groups of models were calculated, using three-dimensional elastic-plastic finite element analyses (FEA) based on FEA codes ABAQUS. In this study, the pipes has an identical defect of local wall thinning, the load properties and values are changed. Three groups of load properties, considering here, were monotonic internal pressure, monotonic moment and both internal pressure and moment, respectively. The numerical simulation conducted on P91 full-scale steel pipes at 625°C, with local wall thinning located at the inner surface. Then, von Mises stress and creep strain of pipes after 100,000h could be obtained corresponding to different models. Based on the analysis, the figures of creep stress and strain varying with load properties were plotted. Then, the stress and strain of pipes with local wall thinning affected by load properties were discussed. The results indicate that creep stress and creep strain increase with load properties. The variation laws have been summarized. The research results can provide the possibility on safety assessment and structure integrity analysis of the pipe with local wall thinning at high temperature effectively.

Effect of Torsion on Collapse Bending Moment for 24-Inch Diameter Schedule 80 Pipes With Wall Thinning

2012 ◽  
Author(s):  
Kunio Hasegawa ◽  
Yinsheng Li ◽  
Bostjan Bezensek ◽  
Phuong Hoang
Keyword(s):  
Power Plants ◽  
Bending Moment ◽  
Combined Loading ◽  
Bending Moments ◽  
Compressive Stresses ◽  
Wall Thinning ◽  
Nominal Thickness ◽  
Calculation Results ◽  
Loading Modes ◽  
Local Wall Thinning

Piping items in power plants may experience combined bending and torsion moments during operation. Currently, there is a lack of guidance in the ASME B&PV Code Section XI for combined loading modes including pressure, torsion and bending. Finite element analyses were conducted for 24-inch diameter Schedule 80 pipes with local wall thinning subjected to tensile and compressive stresses. Plastic collapse bending moments were calculated under constant torsion moments. From the calculation results, it can be seen that collapse bending moment for pipes with local thinning subjected to tensile stress is smaller than that subjected to compressive stress. In addition, equivalent moment is defined as the root the sum of the squares of the torsion and bending moments. It is found that the equivalent moments can be approximated with the pure bending moments, when the wall thinning length is equal or less than 7.73R·t for the wall thinning depth of 75% of the nominal thickness, where R is the mean radius and t is the wall thickness of the pipe.

Effect of Circumferential Location of Local Wall Thinning Defect on the Collapse Moment of Elbow

2006 ◽  
Author(s):  
Jin Weon Kim ◽  
Yeon Soo Na ◽  
Chi Yong Park
Keyword(s):  
Carbon Steel ◽  
Internal Pressure ◽  
Nuclear Power ◽  
Three Dimensional ◽  
Piping System ◽  
Main Concern ◽  
Wall Thinning ◽  
Bending Load ◽  
Local Wall Thinning ◽  
Steel Piping

Local wall-thinning due to flow-accelerated corrosion is one of the degradation mechanisms of carbon steel piping in nuclear power plant (NPP). It is a main concern in carbon steel piping systems in terms of the safety and operability of the NPP. Recently, the integrity of piping components containing local wall-thinning has become more important for maintaining the reliability of a nuclear piping system, and has been the subject of several studies. However, although wall-thinning in pipe bends and elbows has been frequently reported, its effect on the integrity of pipe bends and elbows has not yet been systematically investigated. Thus, the purpose of this study was to investigate the effect of the circumferential location of a local wall-thinning defect on the collapse behavior of an elbow. For this purpose, the present study used three-dimensional finite element analyses on a 90-degree elbow containing local wall-thinning at the crown of the bend region and evaluated the collapse moment of the wall-thinned elbow under various thinning geometries and loading conditions. The combined internal pressure and bending loads were considered as an applied load. Internal pressure of 0∼20 MPa and both closing-and opening-mode bending were applied. The results of the analyses showed that a reduction in the collapse moment of the elbow due to local wall-thinning was more significant when a defect was located at the crown than when a defect was located at the intrados and extrados. Also, the effect of the internal pressure on the collapse moment depended on the circumferential location of the thinning defect and mode of the bending load.

An Experimental Study on the Evaluation of Failure Behavior of Pipe With Local Wall Thinning

2002 ◽  
Author(s):  
Jin Weon Kim ◽  
Chi Yong Park
Keyword(s):  
Internal Pressure ◽  
Failure Mode ◽  
Carrying Capacity ◽  
Axial Length ◽  
Failure Behavior ◽  
Load Carrying Capacity ◽  
Wall Thinning ◽  
Load Carrying ◽  
Deformation Ability ◽  
Local Wall Thinning

The pipe failure tests were performed using 102mm-Sch.80 carbon steel pipe with various simulated local wall thinning defects, in the present study, to investigate the failure behavior of pipe thinned by flow accelerated corrosion (FAC). The failure mode, load carrying capacity, and deformation ability were analyzed from the results of experiments conducted under loading conditions of 4-point bending and internal pressure. A failure mode of pipe with a defect depended on the magnitude of internal pressure and axial thinning length as well as stress type and thinning depth and circumferential angle. Also, the results indicated that the load carrying capacity and deformation ability were depended on stress state in the thinning region and dimensions of thinning defect. With increase in axial length of thinning area, for applying tensile stress to the thinning region, the dependence of load carrying capacity was determined by circumferential thinning angle, and the deformation ability was proportionally increased regardless of the circumferential angle. For applying compressive stress to thinning region, however, the load carrying capacity was decreased with increase in axial length of the thinned area. Also, the effect of internal pressure on failure behavior was characterized by failure mode of thinned pipe, and it promoted crack occurrence and mitigated a local buckling of the thinned area.

Sign in / Sign up

Export Citation Format

Share Document