Turbulent Heat Transfer in an Enclosure With a Horizontal Permeable Plate in the Middle

2006 ◽  
Vol 128 (11) ◽  
pp. 1122-1129 ◽  
Author(s):  
Edimilson J. Braga ◽  
Marcelo J. S. de Lemos
Keyword(s):  
Heat Transfer ◽  
Porous Plate ◽  
Porous Matrix ◽  
Turbulent Heat Transfer ◽  
Turbulent Heat ◽  
Turbulent Natural Convection ◽  
Nusselt Numbers ◽  
Model Solutions ◽  
Volume Method ◽  
Rayleigh Numbers

Turbulent natural convection in a vertical two-dimensional square cavity, isothermally heated from below and cooled at the upper surface, is numerically analyzed using the finite volume method. The enclosure has a thin horizontal porous obstruction, made of a highly porous material and extremely permeable, located at the cavity midheight. Governing equations are written in terms of primitive variables and are recast into a general form. For empty cavities, no discrepancies result for the Nusselt number when laminar and turbulent model solutions are compared for Rayleigh numbers up to 107. Also, in general the porous obstruction decreases the heat transfer across the heated walls showing overall lower Nusselt numbers when compared with those without the porous obstruction. However, the presence of a porous plate in the cavity seems to force an earlier separation from laminar to turbulence model solutions due to higher generation rates of turbulent kinetic energy into the porous matrix.

Turbulent Heat Transfer in a Horizontal Enclosure With a Thin Porous Obstruction in the Middle

2003 ◽  
Author(s):  
Edimilson J. Braga ◽  
Marcelo J. S. de Lemos
Keyword(s):  
Heat Transfer ◽  
Porous Matrix ◽  
Turbulent Heat Transfer ◽  
Turbulent Heat ◽  
Turbulent Regime ◽  
Square Cavity ◽  
Turbulent Natural Convection ◽  
Nusselt Numbers ◽  
Volume Method ◽  
Generalized Coordinate

Turbulent natural convection in a horizontal two-dimensional square cavity, isothermally heated from below and cooled at the upper surface, is numerically analyzed using the finite volume method and a generalized coordinate system. The enclosure has a thin horizontal porous obstruction located at the cavity mid height. Governing equations are written in terms of primitive variables and are recast into a general from. In general, the porous obstruction decreases the heat transfer across the heated walls showing an overall lower Nusselt numbers when compared with those without the same porous obstruction. However, the presence of a porous obstruction. However, the presence of a porous obstruction in a square cavity seems to force an earlier transition from laminar to turbulent regime due to higher generation rates of turbulent kinetic energy into the porous matrix.

scholarly journals Effect of Rayleigh Number on Internal Eccentricity in a Heated Horizontal Elliptical Cylinder to its Coaxial Square Enclosure

2020 ◽  
Vol 25 (3) ◽  
pp. 17-29
Author(s):  
Abdelkrim Bouras ◽  
Djedid Taloub ◽  
Zied Driss
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Outer Cylinder ◽  
Boussinesq Approximation ◽  
Square Enclosure ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Commercial Code ◽  
Volume Method ◽  
Rayleigh Numbers

AbstractThis paper deals with numerical investigation of a natural convective flow in a horizontal annular space between a heated square inner cylinder and a cold elliptical outer cylinder with a Newtonian fluid. Uniform temperatures are imposed along walls of the enclosure. The governing equations of the problem were solved numerically by the commercial code Fluent, based on the finite volume method and the Boussinesq approximation. The effects of Geometry Ratio GR and Rayleigh numbers on fluid flow and heat transfer performance are investigated. The Rayleigh number is varied from 103 to 106. Throughout the study the relevant results are presented in terms of isotherms, and streamlines. From the results, we found that the increase in the Geometry Ratio B leads to an increase of the heat transfer coefficient. The heat transfer rate in the annulus is translated in terms of the average Nusselt numbers along the enclosure’s sides. Tecplot 7 program was used to plot the curves which cleared these relations and isotherms and streamlines which illustrate the behavior of air through the channel and its variation with other parameters. The results for the streamlines, isotherms, local and average Nusselt numbers average Nusselt numbers are compared with previous works and show good agreement.

Turbulent Heat Transfer and Fluid Flow in an Unsymmetrically Heated Triangular Duct

1980 ◽  
Vol 102 (4) ◽  
pp. 590-597 ◽  
Author(s):  
C. A. C. Altemani ◽  
E. M. Sparrow
Keyword(s):  
Heat Transfer ◽  
Hydraulic Diameter ◽  
Turbulent Heat Transfer ◽  
Turbulent Heat ◽  
General Applicability ◽  
Thermal Boundary Conditions ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Turbulent Airflow ◽  
Thermal Entrance

Experiments were performed to determine entrance-region and fully developed heat transfer characteristics for turbulent airflow in an unsymmetrically heated equilateral triangular duct; friction factors were also measured. Two of the walls were heated while the third was not directly heated. The resulting thermal boundary conditions consisted of uniform heating per unit axial length and circumferentially uniform temperature on the heated walls. Special techniques were employed to minimize extraneous heat losses, and numerical finite-difference solutions played an important role in both the design of the apparatus and in the data reduction. The thermal entrance lengths required to attain thermally developed conditions were found to increase markedly with the Reynolds number and were generally greater than those for conventional pipe flows—a behavior which can be attributed to the unsymmetric heating. The fully developed Nusselt numbers were compared with circular tube correlations from the literature, from which it was shown that the hydraulic diameter is not fully sufficient to rationalize the circular and noncircular duct results. However, excellent Nusselt number predictions were obtained by employing the Petukhov-Popou correlation in conjunction with the measured friction factors for the triangular duct. This approach may have general applicability for predicting noncircular duct heat transfer. The friction factor results also affirmed the inadequacies of the hydraulic diameter but supported a general noncircular duct correlation available in the literature.

Turbulent Heat Transfer in Corrugated-Wall Channels With and Without Fins

1987 ◽  
Vol 109 (1) ◽  
pp. 62-67 ◽  
Author(s):  
R. S. Amano ◽  
A. Bagherlee ◽  
R. J. Smith ◽  
T. G. Niess
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Reynolds Stress Model ◽  
Turbulent Heat Transfer ◽  
Turbulent Heat ◽  
Reynolds Stresses ◽  
Flow Recirculation ◽  
Nusselt Numbers ◽  
Visible Effect ◽  
Corrugated Wall

A numerical study is performed examining flow and heat transfer characteristics in a channel with periodically corrugated walls. The complexity of the flow in this type of channel is demonstrated by such phenomena as flow impingement on the walls, separation at the bend corners, flow reattachment, and flow recirculation. Because of the strong nonisotropic nature of the turbulent flow in the channel, the full Reynolds-stress model was employed for the evaluation of turbulence quantities. Computations are made for several different corrugation periods and for different Reynolds numbers. The results computed by using the present model show excellent agreement with experimental data for mean velocities, the Reynolds stresses, and average Nusselt numbers. The study was further extended to a channel flow where fins are inserted at bends in the channel. It was observed that the insertion of fins in the flow passage has a visible effect on flow patterns and skin friction along the channel wall.

scholarly journals Modelling turbulent heat transfer in rough channels using phenomenological theory

2021 ◽  
Vol 2116 (1) ◽  
pp. 012025
Author(s):  
J W R Peeters
Keyword(s):  
Heat Transfer ◽  
Phenomenological Theory ◽  
Velocity Fields ◽  
Turbulent Heat Transfer ◽  
Turbulent Heat ◽  
Wall Roughness ◽  
Thermal Fields ◽  
Nusselt Numbers ◽  
Rough Walls ◽  
Friction Factors

Abstract Rough walls are often encountered in industrial heat transfer equipment. Even though it is well known that a rough wall affects velocity fields and thermal fields differently (and therefore also skin friction factors and Stanton or Nusselt numbers), predicting the effect of rough walls on turbulent heat transfer remains difficult. A relation between the scalar spectrum and the Stanton number is derived for channels with both smooth and rough walls. It is shown that the new relation agrees reasonably well with recent DNS experiments for wall roughness sizes of k + < 150 and when Pr = 0.7 − 1.0. Under these conditions, a thermal analogue of Moody’s diagram can be created using the newly developed relation.

Effect of Surface Emissivity on Conjugate Turbulent Natural Convection in an Air-Filled Cavity with a Heat Source

2016 ◽  
Vol 685 ◽  
pp. 315-319 ◽  
Author(s):  
Igor V. Miroshnichenko ◽  
Mikhail A. Sheremet
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Source ◽  
Surface Radiation ◽  
Turbulent Heat Transfer ◽  
Turbulent Heat ◽  
Heat Conducting ◽  
Surface Emissivity ◽  
Turbulent Natural Convection ◽  
Effect Of Surface

The interaction of conjugate turbulent natural convection and surface thermal radiation in an air-filled square enclosure having heat-conducting solid walls of finite thickness and a heat source has been numerically studied. The primary focus was on the influence of surface emissivity on complex heat transfer. The mathematical model has been formulated in dimensionless variables such as stream function, vorticity and temperature using k-ε turbulent model. The effect of surface emissivity on the average total Nusselt number has been defined. The distributions of streamlines and temperature fields, describing characteristics of the analyzed fluid flow and heat transfer have been obtained. The results clearly show an essential effect of surface radiation on unsteady turbulent heat transfer.

Numerical Investigation on Air Side Performance of Fin-and-Tube Heat Exchangers With Large Diameter Tubes and Large Number of Tube Rows

2011 ◽  
Author(s):  
Feng Zhou ◽  
David Geb ◽  
Ivan Catton
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Large Diameter ◽  
Turbulent Heat Transfer ◽  
Navier Stokes ◽  
Turbulent Heat ◽  
Tube Heat Exchanger ◽  
Ansys Cfx ◽  
Sst Model ◽  
Volume Method

In the present study, air-side turbulent heat transfer and friction characteristics of fin-and-tube heat exchangers with a large number of tube rows and large diameter of tubes are investigated numerically. Finite Volume Method based CFD software, Ansys CFX, was used as the 3-D Reynolds-averaged Navier-Stokes Solver. A k-ω based Shear-Stress-Transport (SST) model was used to predict the turbulent flow and heat transfer through the fin-and-tube heat exchanger coil. The effects of parameters such as Reynolds number, the number of tube rows, tube diameter, tube pitches and fin pitch are examined. In the end, correlations for the Nusselt number and friction factor which applicable to fin-and-tube heat exchangers with large number of large-diameter tube rows are proposed.

Turbulent Heat Transfer Downstream of an Unsymmetric Blockage in a Tube

1978 ◽  
Vol 100 (4) ◽  
pp. 588-594 ◽  
Author(s):  
K. K. Koram ◽  
E. M. Sparrow
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Turbulent Heat Transfer ◽  
Working Fluid ◽  
Initial Increase ◽  
Turbulent Heat ◽  
Transfer Coefficients ◽  
Tube Cross Section ◽  
Nusselt Numbers ◽  
Prandtl Numbers

Pipe flow experiments were performed to study the heat transfer in the separation, reattachment, and redevelopment regions downstream of a wall-attached blockage in the form of a segmental orifice plate. Water was the working fluid, and the Reynolds number encompassed the range from about 10,000–60,000. The extent of the flow blockage was varied from one-fourth to three-fourths of the tube cross section. Heat transfer coefficients were determined both around the circumference of the uniformly heated tube and along its length. The axial distributions of the circumferential average Nusselt numbers show an initial increase, then attain a maximum, and subsequently decrease toward the fully developed regime. These Nusselt numbers are much higher than those for a conventional thermal entrance region. The unsymmetric blockage induces variations of the Nusselt number around the circumference of the tube. Axial distributions of the Nusselt number at various fixed angular positions reveal the presence of two types of maxima. One of these is associated with the reattachment of the flow and the other occurs due to the impingement of flow deflected by the blockage onto the tube wall. The circumferential variations decay with increasing downstream distance, but the rate of decay for the case of the smallest blockage is remarkably slow. Although most of the tests were performed for Pr = 4, supplementary experiments for Pr = 8 showed that the results are valid for a range of Prandtl numbers.

scholarly journals Numerical Study of Heat Transfer by Natural Convection in Concentric Hexagonal Cylinders Charged with a Nanofluid

2022 ◽  
Vol 17 ◽  
pp. 19-28
Author(s):  
Taloub Djedid ◽  
Bouras Abdelkrim ◽  
Zied Driss
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Volume Fraction ◽  
Numerical Study ◽  
Outer Cylinder ◽  
Boussinesq Approximation ◽  
Fixed Temperature ◽  
Nusselt Numbers ◽  
Volume Method ◽  
Rayleigh Numbers

In this document, a numerical study of the natural convection of steady-state laminar heat transfer in a horizontal ring between a heated hexagonal inner cylinder and a cold hexagonal outer cylinder. A Cu - water nanofluid traverses this annular space. The system of equations governing the problem was solved numerically by the fluent calculation code based on the finite volume method. Based on the Boussinesq approximation. The interior and exterior sides from the two cylinders are maintained at a fixed temperature. We investigated the impacts of various thermal Rayleigh numbers (103≤ Rat ≤2.5x105), and the volume fraction from the nanoparticles (0≤ Ø ≤0.12) on fluid flow and heat transfer performance. It is found that in high thermal Rayleigh numbers, a thin thermal boundary layer is illustrated at the flow that heavily strikes the ceiling and lower from the outer cylinder. In addition, the local and mean Nusselt number from a nanofluid are enhanced by enhancing the volume fraction of the nanoparticles.The results are shown within the figure of isocurrents, isotherms, and mean and local Nusselt numbers. Detailed results of the numerical has been compared with literature ones, and it gives a reliable agreement.

Sign in / Sign up

Export Citation Format

Share Document