Thermal Performance of Multipass Parallel and Counter-Cross-Flow Heat Exchangers

2006 ◽  
Vol 129 (3) ◽  
pp. 282-290 ◽  
Author(s):  
Luben Cabezas-Gómez ◽  
Hélio Aparecido Navarro ◽  
José Maria Saiz-Jabardo
Keyword(s):  
Heat Exchanger ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
Experimental Studies ◽  
Cross Flow ◽  
Numerical Procedure ◽  
Complex Flow ◽  
Flow Heat ◽  
Small Elements ◽  
Effectiveness Data

A thorough study of the thermal performance of multipass parallel cross-flow and counter-cross-flow heat exchangers has been carried out by applying a new numerical procedure. According to this procedure, the heat exchanger is discretized into small elements following the tube-side fluid circuits. Each element is itself a one-pass mixed-unmixed cross-flow heat exchanger. Simulated results have been validated through comparisons to results from analytical solutions for one- to four-pass, parallel cross-flow and counter-cross-flow arrangements. Very accurate results have been obtained over wide ranges of NTU (number of transfer units) and C* (heat capacity rate ratio) values. New effectiveness data for the aforementioned configurations and a higher number of tube passes is presented along with data for a complex flow configuration proposed elsewhere. The proposed procedure constitutes a useful research tool both for theoretical and experimental studies of cross-flow heat exchangers thermal performance.

Performance Analysis of Multi-Pass Cross-Flow Heat Exchangers

2018 ◽  
Author(s):  
Kiran Lankalapalli ◽  
Ahmed ElSawy ◽  
Stephen Idem
Keyword(s):  
Heat Exchanger ◽  
Performance Analysis ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Threshold Value ◽  
Finned Tube ◽  
Flow Heat ◽  
Rate Ratios ◽  
Side Flow

A steady state sensible performance analysis of multi-pass cross-flow finned-tube heat exchangers is reported. The investigation considers various flow circuiting, such as counter cross-flow, parallel cross-flow, and cross-flow where the tube-side flow is in parallel. A previously developed matrix approach is used to evaluate the heat exchanger performance in each tube pass. The equations required to model the thermal performance of these configurations are presented, and the thermal performance is compared for each type of flow circuiting. Thereafter a parametric study on cross-flow heat exchanger performance is performed by varying physically significant parameters such as number of transfer units (NTU) and capacity rate ratios, and the graphical results for each type of flow circuiting are presented both for both two-pass and three-pass arrangements. A consistent criterion is proposed for each case, wherein increasing the NTU beyond a certain threshold value does not significantly improve heat exchanger thermal performance.

Minimum Irreversibility Criteria for Heat Exchanger Configurations

1999 ◽  
Vol 121 (4) ◽  
pp. 241-246 ◽  
Author(s):  
F. E. M. Saboya ◽  
C. E. S. M. da Costa
Keyword(s):  
Heat Capacity ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Second Law Of Thermodynamics ◽  
The Other ◽  
Maximum Heat ◽  
Transfer Rates ◽  
Mass Flow Rates ◽  
Flow Heat

From the second law of thermodynamics, the concepts of irreversibility, entropy generation, and availability are applied to counterflow, parallel-flow, and cross-flow heat exchangers. In the case of the Cross-flow configuration, there are four types of heat exchangers: I) both fluids unmixed, 2) both fluids mixed, 3) fluid of maximum heat capacity rate mixed and the other unmixed, 4) fluid of minimum heat capacity rate mixed and the other unmixed. In the analysis, the heat exchangers are assumed to have a negligible pressure drop irreversibility. The Counterflow heat exchanger is compared with the other five heat exchanger types and the comparison will indicate which one has the minimum irreversibility rate. In this comparison, only the exit temperatures and the heat transfer rates of the heat exchangers are different. The other conditions (inlet temperatures, mass flow rates, number of transfer units) and the working fluids are the same in the heat exchangers.

Transient Response of Cross Flow Heat Exchangers Subjected to Simultaneous Temperature and Flow Perturbations

2015 ◽  
Vol 799-800 ◽  
pp. 665-670
Author(s):  
Karthik Silaipillayarputhur
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Convection Heat Transfer ◽  
Cross Flow ◽  
Balance Equations ◽  
Transfer Resistance ◽  
Mass Flow Rates ◽  
Flow Heat ◽  
Transient Thermal ◽  
Central Finite Difference

This paper compares the transient thermal performance between counter and parallel cross flow heat exchangers subjected to time varying inlet mass flow rates and inlet temperatures that hasn’t been previously discussed in the available literature. Specifically the transient performance of 2 pass and 3 pass cross flow heat exchangers is discussed in this paper. In the present study the energy balance equations for the hot and cold fluids and the heat exchanger wall were solved using an implicit central finite difference method. Representative values of NTU were considered, and the NTU’s of the heat exchanger were assumed to be uniformly distributed among the heat exchanger passes. Other physically significant parameters such as the capacity rate ratio and the convection heat transfer resistance ratio were systematically varied. A detailed summary based on the observations has been presented.

Transient Response of a Cross Flow Heat Exchanger Subjected to Temperature and Flow Perturbations

2015 ◽  
Author(s):  
Karthik Silaipillayarputhur ◽  
Stephen A. Idem
Keyword(s):  
Heat Exchanger ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Transient Performance ◽  
Numerical Predictions ◽  
Minimum Capacity ◽  
Flow Heat

The transient performance of a multi-pass cross flow heat exchanger subjected to temperature and mass flow rate perturbations, where the heat exchanger flow circuiting is neither parallel flow nor counter flow, is considered in this work. A detailed numerical study was performed for representative single-pass, two-pass, and three-pass heat exchangers. Numerical predictions were obtained for cases where the minimum capacity rate fluid was subjected to a step change in inlet temperature in absence of mass flow rate perturbations. Likewise, numerical predictions were obtained for the heat exchangers operating initially at steady state, where a step mass flow rate change of the minimum capacity rate fluid was imposed in the absence of any fluid temperature perturbations. The transient performance of this particular heat exchanger configuration subjected to these temperature and flow disturbances has not been discussed previously in the available literature. In the present study the energy balance equations for the hot and cold fluids and the heat exchanger wall were solved using an implicit central finite difference method. A parametric study was conducted by varying the dimensionless quantities that govern the transient response of the heat exchanger over a typical range of values. Because of the storage of energy in the heat exchanger wall, and finite propagation times associated with the inlet perturbations, the outlet temperatures of both fluids do not respond instantaneously. The results are compared with previously published transient performance predictions of multi-pass counter flow and parallel flow heat exchangers.

Thermal performance escalation of cross flow heat exchanger using in-line elliptical tubes

2019 ◽  
Vol 33 (7) ◽  
pp. 587-612 ◽  
Author(s):  
Chidanand K. Mangrulkar ◽  
Ashwinkumar S. Dhoble ◽  
Pawan Kumar Pant ◽  
Nitin Kumar ◽  
Ashutosh Gupta ◽  
...  
Keyword(s):  
Heat Exchanger ◽  
Thermal Performance ◽  
Cross Flow ◽  
Flow Heat

Cross-Flow Heat Exchanger: Volume-Averaging Formulation of a Unit Cell Model and Thermal Performance Analysis

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Hengyun Zhang ◽  
Zhaoqiang Wang
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Thermal Performance ◽  
Cell Model ◽  
Cross Flow ◽  
Volume Averaging ◽  
Unit Cell ◽  
Unit Cell Model ◽  
Flow Heat ◽  
The Cross

A formulation of the unit cell model and the corresponding thermal performance analysis for the cross-flow heat exchanger are carried out, with the design goal of dissipating 175 W from a high-power electronic chip in a compact space. A liquid to liquid heat exchanger in the cross-flow arrangement is preferred due to its compact size and high effectiveness. The unit cell model is formulated based on the volume-averaging method to determine the heat transfer coefficient involving two heat exchanging fluids and a solid. The various factors such as channel shape, channel edge length, channel size, and heat exchanger material can be examined based on the unit cell model. The obtained heat transfer coefficients are used for the estimation of the heat exchanger thermal performance based on the effectiveness–number of transfer units (NTU) correlation. To verify the model formulation, the heat and fluid flow over the cross-flow heat exchangers are investigated through the full-field numerical computation. The amount of heat exchanged from the numerical computation is extracted and compared with the predicted results from the unit cell model. A fairly good agreement is obtained between the two approaches. Based on the unit cell model, an aluminum cross heat exchanger with eight channel layers for the hot and cold fluids, 15 channels in each layer with a channel diameter of 2 mm, is able to meet the design target.

Review and Analysis of Cross Flow Heat Exchanger Transient Modeling for Flow Rate and Temperature Variations

2015 ◽  
Vol 7 (4) ◽  
Author(s):  
Tianyi Gao ◽  
James Geer ◽  
Bahgat Sammakia
Keyword(s):  
Heat Exchanger ◽  
Mass Flow Rate ◽  
Transient Response ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Inlet Temperature ◽  
Flow Rate Change ◽  
Flow Heat

Heat exchangers are important facilities that are widely used in heating, ventilating, and air conditioning (HVAC) systems. For example, heat exchangers are the primary units used in the design of the heat transfer loops of cooling systems for data centers. The performance of a heat exchanger strongly influences the thermal performance of the entire cooling system. The prediction of transient phenomenon of heat exchangers is of increasing interest in many application areas. In this work, a dynamic thermal model for a cross flow heat exchanger is solved numerically in order to predict the transient response under step changes in the fluid mass flow rate and the fluid inlet temperature. Transient responses of both the primary and secondary fluid outlet temperatures are characterized under different scenarios, including fluid mass flow rate change and a combination of changes in the fluid inlet temperature and the mass flow rate. In the ε-NTU (number of transfer units) method, the minimum capacity, denoted by Cmin, is the smaller of Ch and Cc. Due to a mass flow rate change, Cmin may vary from one fluid to another fluid. The numerical procedure and transient response regarding the case of varying Cmin are investigated in detail in this study. A review and comparison of several journal articles related to the similar topic are performed. Several sets of data available in the literatures which are in error are studied and analyzed in detail.

Thermal Performance Modeling of Cross-Flow Heat Exchangers

2015 ◽  
Author(s):  
Luben Cabezas-Gómez ◽  
Hélio Aparecido Navarro ◽  
José Maria Saíz-Jabardo
Keyword(s):  
Thermal Performance ◽  
Heat Exchangers ◽  
Performance Modeling ◽  
Cross Flow ◽  
Flow Heat

Unit Cell Model Formulation and Thermal Performance Analysis for Cross-Flow Heat Exchanger

2016 ◽  
Author(s):  
Hengyun Zhang ◽  
Zhaoqiang Wang ◽  
Yansong Wang
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Thermal Performance ◽  
Cell Model ◽  
Cross Flow ◽  
Volume Averaging ◽  
Unit Cell ◽  
Unit Cell Model ◽  
Flow Heat ◽  
The Cross

An analysis for the cross-flow heat exchanger is conducted for electronic cooling applications, with the design goal of dissipating 175W from high power chip by maintaining the chip temperature within 85 °C in a compact space. Liquid to liquid heat exchanger in cross flow arrangement is preferred due to its compact size and high effectiveness. A volume averaging formulation is developed to determine the heat transfer coefficient at the unit cell level. The effects of channel shape, channel size, and heat exchanger material are examined through the heat transfer in the unit cell model. The obtained heat transfer coefficients are also used for the estimation of the heat exchanger thermal performance based on the effectiveness-NTU method. To verify the volume averaging formulation, a full field heat and fluid flow over the cross-flow heat exchangers are investigated through numerical computation. The amount of heat exchanged is extracted and compared with the unit cell model prediction. A fairly good agreement is obtained between the two approaches. Fabrication of cross-flow heat exchanger is further discussed to meet the design target.

Sign in / Sign up

Export Citation Format

Share Document