Inelastic Deformation Under Nonisothermal Loading

1990 ◽  
Vol 112 (1) ◽  
pp. 15-25 ◽  
Author(s):  
K. S. Chan ◽  
U. S. Lindholm

The objective of this paper is to evaluate, both experimentally and analytically, the appropriate forms of the hardening evolution equations in unified constitutive models for conditions involving nonisothermal loading. Critical experiments were performed for a cast nickel-base superalloy by using variable temperature tensile, creep, and cyclic tests in the 538°C–982°C temperature range. These experimental results were compared with both isothermal data and predictions of the Bodner-Partom elastic-viscoplastic theory to assess the effects of thermal history on constitutive behavior. The results indicate that the hardening evolution equations based on isothermal data are applicable for nonisothermal loading of these precipitation strengthened alloys. Additional thermal history effect terms in the hardening evolution equations were not required beyond those accounting for the variation of material constants with temperature. Using material constants determined solely from isothermal data, the inelastic deformation behavior of B1900 + Hf subject to thermomechanical loading were adequately predicted by the Bodner-Partom model.

1970 ◽  
Vol 37 (3) ◽  
pp. 759-764 ◽  
Author(s):  
P. R. Paslay ◽  
C. H. Wells ◽  
G. R. Leverant

The orientation and stress dependence of the primary creep rate in single crystals of a nickel-base superalloy is predicted from crystallographic deformation mechanisms. An experimentally determined relationship between the deformation rate and applied stress is employed to calculate the independent contributions of each of the possible slip systems to the strain rate. Calculations were made for single crystals of a nickel-base superalloy tested in tensile creep at 1400 deg F, at which temperature the active slip planes are known to be {111}, and the slip directions either 〈110〉 or 〈112〉 at high or low strain rates, respectively. Comparison with measured primary creep rates showed the 〈110〉 contribution to be negligible and that while semi-quantitative agreement with the 〈112〉 analysis was obtained, an accurate prediction of creep rates may require inclusion of strain hardening in the analysis.


2007 ◽  
Vol 546-549 ◽  
pp. 1225-1228
Author(s):  
Fan Lai Meng ◽  
Su Gui Tian ◽  
Ming Gang Wang ◽  
Xing Fu Yu ◽  
Hong Qiang Du ◽  
...  

By means of tensile and compression creep testing and SEM, TEM observation, an investigation has been made into the microstructure evolution of a single crystal nickel base superalloy during tensile / compression creep. Results show that the cubic γ′ phase in the superalloy is transformed into the N-type meshlike structure along the direction vertical to stress axis during tensile creep. The cubic γ′ phase is transformed into the P-type structure along the direction parallel to stress axis during compression creep. An obvious asymmetry strain of the alloy occurs during tensile and compression creep, the formation of the needle-like γ′ rafts during compression creep is a main reason of the alloy displaying a smaller strain. During compressive creep, the deformation feature of the alloy is the <110> and (1/3) <112> super dislocations shearing into the γ′ rafts. The deformation mechanism of the alloy, in the stage state of tensile creep, is dislocation climb over the γ′ rafts.


2007 ◽  
Vol 353-358 ◽  
pp. 511-514
Author(s):  
Ying Li ◽  
Hui Chen Yu ◽  
Xue Ren Wu ◽  
Xiao Guang Yang ◽  
Duo Qi Shi

Tensile creep tests were conducted at 980°C under a constant stress on a single crystal nickel base superalloy. Some tests were interrupted at different stages during the creep process. The strain-time curves indicated that this alloy exhibited conventional primary, steady-state and tertiary stages at this temperature. The transmission electron microscope (TEM) observations of foils taken from the gauge sections of specimens were made to interpret the microstructural evolution that occurred during the creep process. It was found that the γ′ particles were rafted in the direction perpendicular to the applied stress. The acceleration of the creep rate was related to the change of the dislocation density.


Sign in / Sign up

Export Citation Format

Share Document