Thermodynamic Analysis of Latent Heat Storage in a Shell-and-Tube Heat Exchanger

1992 ◽  
Vol 114 (2) ◽  
pp. 93-99 ◽  
Author(s):  
Ch. Charach ◽  
A. Zemel
Keyword(s):  
Heat Transfer ◽  
Latent Heat ◽  
Entropy Generation ◽  
Gas Flow ◽  
Heat Storage ◽  
Cylindrical Tube ◽  
Design Parameters ◽  
Storage Process ◽  
Latent Heat Storage ◽  
Tube Heat Exchanger

This work addresses the entropy generation aspects of a latent heat storage in which the energy delivered by a hot gas flowing through a cylindrical tube induces melting of the material surrounding the tube. The heat transfer for conduction-dominated melting is analyzed, taking into account the two-dimensional effects. The storage process irreversibilities associated with both the gas flow and the heat transfer (including entropy generation in the melted layer) are considered. The number of entropy generation units, which is a measure of the thermodynamic imperfection of the energy storage process, is expressed as a function of the main design parameters of the system. Analytic bounds and simplified asymptotic expressions for this quantity are derived. The results are compared with earlier one-dimensional studies.

Second-Law Efficiency of an Energy Storage-Removal Cycle in a Phase-Change Material Shell-and-Tube Heat Exchanger

1993 ◽  
Vol 115 (4) ◽  
pp. 240-243 ◽  
Author(s):  
Ch. Charach
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Phase Change ◽  
Phase Change Material ◽  
Latent Heat ◽  
Heat Storage ◽  
Latent Heat Storage ◽  
Tube Heat Exchanger ◽  
Shell And Tube ◽  
Change Material

This communication extends the thermodynamic analysis of latent heat storage in a shell-and-tube heat exchanger, developed recently, to the complete heat storage-removal cycle. Conditions for the cyclic operation of this system are formulated within the quasi-steady approximation for the axisymmetric two-dimensional conduction-controlled phase change. Explicit expressions for the overall number of entropy generation units that account for heat transfer and pressure drop irreversibilities are derived. Optimization of this figure of merit with respect to the freezing point of the phase-change material and with respect to the number of heat transfer units is analyzed. When the frictional irreversibilities of the heat removal stage are negligible, the results of these studies are in agreement with those developed recently by De Lucia and Bejan (1991) for a one-dimensional latent heat storage system.

scholarly journals Effect of Twisted Fin Array in a Triple-Tube Latent Heat Storage System during the Charging Mode

2021 ◽  
Vol 13 (5) ◽  
pp. 2685
Author(s):  
Mohammad Ghalambaz ◽  
Jasim M. Mahdi ◽  
Amirhossein Shafaghat ◽  
Amir Hossein Eisapour ◽  
Obai Younis ◽  
...  
Keyword(s):  
Energy Storage ◽  
Heat Exchanger ◽  
Latent Heat ◽  
Thermal Energy ◽  
Heat Storage ◽  
Hot Water ◽  
Melting Time ◽  
Latent Heat Storage ◽  
Tube Heat Exchanger ◽  
Storage Rate

This study aims to assess the effect of adding twisted fins in a triple-tube heat exchanger used for latent heat storage compared with using straight fins and no fins. In the proposed heat exchanger, phase change material (PCM) is placed between the middle annulus while hot water is passed in the inner tube and outer annulus in a counter-current direction, as a superior method to melt the PCM and store the thermal energy. The behavior of the system was assessed regarding the liquid fraction and temperature distributions as well as charging time and energy storage rate. The results indicate the advantages of adding twisted fins compared with those of using straight fins. The effect of several twisted fins was also studied to discover its effectiveness on the melting rate. The results demonstrate that deployment of four twisted fins reduced the melting time by 18% compared with using the same number of straight fins, and 25% compared with the no-fins case considering a similar PCM mass. Moreover, the melting time for the case of using four straight fins was 8.3% lower than that compared with the no-fins case. By raising the fins’ number from two to four and six, the heat storage rate rose 14.2% and 25.4%, respectively. This study presents the effects of novel configurations of fins in PCM-based thermal energy storage to deliver innovative products toward commercialization, which can be manufactured with additive manufacturing.

Quasi-stationary modelling of solidification in a latent heat storage comprising a plain tube heat exchanger

2018 ◽  
Vol 20 ◽  
pp. 551-559 ◽  
Author(s):  
A. Stamatiou ◽  
S. Maranda ◽  
F. Eckl ◽  
P. Schuetz ◽  
L. Fischer ◽  
...  
Keyword(s):  
Heat Exchanger ◽  
Latent Heat ◽  
Heat Storage ◽  
Latent Heat Storage ◽  
Tube Heat Exchanger ◽  
Plain Tube

scholarly journals Effective Separation of a Water in Oil Emulsion from a Direct Contact Latent Heat Storage System

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2264 ◽  
Author(s):  
Sebastian Ammann ◽  
Andreas Ammann ◽  
Rebecca Ravotti ◽  
Ludger Fischer ◽  
Anastasia Stamatiou ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Latent Heat ◽  
Direct Contact ◽  
Heat Storage ◽  
Storage System ◽  
Heat Transfer Fluid ◽  
Storage Unit ◽  
Latent Heat Storage ◽  
Oil Emulsion ◽  
Water In Oil Emulsion

The problem of emulsification between Phase Change Material (PCM) and Heat Transfer Fluid (HTF) in direct contact latent heat storage systems has been reported in various studies. This issue causes the PCM to flow out of the storage tank and crystallize at unwanted locations and thus presents a major limitation for the proper operation of such systems. These anomalies become more pronounced when high HTF flow rates are employed with the aim to achieve fast heat transfer rates. The goal of this paper is to find a method which will enable the fast separation of the formed emulsion and thus the uninterrupted operation of the storage unit. In this study, three separation methods were examined and the use of superhydrophobic filters was chosen as the best candidate for the demulsification of the PCM and HTF mixtures. The filter was produced by processing of a melamine sponge with different superhydrophobic adhesives and was tested with emulsions closely resembling the ones formed in a real direct contact setup. The superhydrophobic filter obtained, was able to separate the emulsions effectively while presenting a very high permeability (up to 1,194,980 kg h−1 m−2 bar−1). This is the first time the use of a superhydrophobic sponge has been investigated in the context of demulsification in direct contact latent heat storage.

Thermal Conductivity Enhancement in a Latent Heat Storage Device

2013 ◽  
Vol 860-863 ◽  
pp. 590-593
Author(s):  
Cha Xiu Guo ◽  
Ding Bao Wang ◽  
Gao Lin Hu
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Solid State ◽  
Liquid Phase ◽  
Phase Change ◽  
Latent Heat ◽  
Heat Storage ◽  
Storage Device ◽  
Latent Heat Storage ◽  
Conductivity Enhancement

High conductivity porosity materials are proposed to enhance the phase change materials (PCM) in order to solve the problem of low conductivity of PCM in the latent heat storage device (LHSD), and two-dimensional numerical simulation is conducted to predict the performance of the PCM by CFD software. During the phase change process, the PCM is heated from the solid state to the liquid phase in the process of melting and from the liquid phase to the solid state in the solidification process. The results show that porosity materials can improve heat transfer rate effectively, but the effect of heat transfer of Al foam is superior to that of graphite foam although the heat storage capacity is almost the same for both. The heat transfer is enhanced and the solidification time of PCM is decreased since the effective thermal conductivity of composite PCM is increased.

Sign in / Sign up

Export Citation Format

Share Document