The Maximal Singularity-Free Workspace of the Gough–Stewart Platform for a Given Orientation

2008 ◽  
Vol 130 (11) ◽  
Author(s):  
Qimi Jiang ◽  
Clément M. Gosselin
Keyword(s):  
Case Studies ◽  
Parallel Mechanism ◽  
Stewart Platform ◽  
Parallel Robots ◽  
Analytic Method ◽  
Robot Design ◽  
Parallel Mechanisms ◽  
Leg Length ◽  
Maximal Singularity ◽  
The Relationship

The maximal singularity-free workspace of parallel mechanisms is a desirable criterion in robot design. However, for a 6DOF parallel mechanism, it is very difficult to find an analytic method to determine the maximal singularity-free workspace around a prescribed point for a given orientation. Hence, a numerical algorithm is presented in this paper to compute the maximal singularity-free workspace as well as the corresponding leg length ranges of the Gough–Stewart platform. This algorithm is based on the relationship between the maximal singularity-free workspace and the singularity surface. Case studies with different orientations are performed to demonstrate the presented algorithm. The obtained results can be applied to the geometric design or parameter (leg length) setup of this type of parallel robots.

Computation of the Maximal Singularity-Free Workspace of the MSSM for a Given Orientation

2007 ◽  
Author(s):  
Qimi Jiang ◽  
Cle´ment M. Gosselin
Keyword(s):  
Case Studies ◽  
Numerical Algorithm ◽  
Parallel Mechanism ◽  
Parallel Robots ◽  
Analytic Method ◽  
Robot Design ◽  
Parallel Mechanisms ◽  
Leg Length ◽  
Maximal Singularity ◽  
The Relationship

The maximal singularity-free workspace of parallel mechanisms is a desirable criterion in robot design. However, for a 6-dof parallel mechanism, it is very difficult to find an analytic method to determine the maximal singularity-free workspace around a prescribed point for a given orientation. Hence, a numerical algorithm is presented in this paper to compute the maximal singularity-free workspace as well as the corresponding leg length ranges of the MSSM Gough-Stewart platform. This algorithm is based on the relationship between the maximal singularity-free workspace and the singularity surface. Case studies with different orientations are performed to demonstrate the presented algorithm. The results obtained can be applied to the geometric design or parameter (leg length) setup of the MSSM parallel robots.

scholarly journals Calibration Method for a Parallel Mechanism Type Machine Tool by Response Surface Methodology –Consideration via Simulation on a Stewart Platform Mechanism–

2010 ◽  
Vol 4 (4) ◽  
pp. 355-363 ◽  
Author(s):  
Hiroshi Yachi ◽  
◽  
Hiroshi Tachiya
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Parallel Mechanism ◽  
Measurement Data ◽  
Calibration Method ◽  
Stewart Platform ◽  
Parallel Mechanisms ◽  
Data Set ◽  
Efficient Data ◽  
Efficient Measurement

This paper proposes a calibration method for parallel mechanisms usingResponse Surface Methodology. This method is a statistical approach to estimating an unknown input-output relationship using a small set of efficient data collected on an intended system. Although identifying locations causing positional errors in a parallel mechanism and precisely measuring the position and posture of the output point are difficult, the proposed calibration method based onResponse Surface Methodologyaims to compensate for positional and postural errors, without indentifying the locations causing these errors, by using a small yet efficient measurement data set. This study analyzes the effectiveness of the method we propose by applying it to a Stewart platform, which is a typical spatial 6-DOF parallel mechanism.

scholarly journals Collision-free workspace of parallel mechanisms based on an interval analysis approach

Robotica ◽  
2016 ◽  
Vol 35 (8) ◽  
pp. 1747-1760 ◽  
Author(s):  
MohammadHadi FarzanehKaloorazi ◽  
Mehdi Tale Masouleh ◽  
Stéphane Caro
Keyword(s):  
Interval Analysis ◽  
Parallel Mechanism ◽  
Spherical Shape ◽  
Stewart Platform ◽  
Analysis Approach ◽  
Parallel Mechanisms ◽  
Planar Case ◽  
End Effector ◽  
Mechanical Interference

SUMMARYThis paper proposes an interval-based approach in order to obtain the obstacle-free workspace of parallel mechanisms containing one prismatic actuated joint per limb, which connects the base to the end-effector. This approach is represented through two cases studies, namely a 3-RPR planar parallel mechanism and the so-called 6-DOF Gough–Stewart platform. Three main features of the obstacle-free workspace are taken into account: mechanical stroke of actuators, collision between limbs and obstacles and limb interference. In this paper, a circle(planar case)/spherical(spatial case) shaped obstacle is considered and its mechanical interference with limbs and edges of the end-effector is analyzed. It should be noted that considering a circle/spherical shape would not degrade the generality of the problem, since any kind of obstacle could be replaced by its circumscribed circle/sphere. Two illustrative examples are given to highlight the contributions of the paper.

Unilateral Manipulability Quality Indices: Generalized Manipulability Measures for Unilaterally Actuated Robots

2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Jonathan Eden ◽  
Darwin Lau ◽  
Ying Tan ◽  
Denny Oetomo
Keyword(s):  
System Dynamics ◽  
Physical Properties ◽  
Case Studies ◽  
Arbitrary Number ◽  
System Analysis ◽  
Parallel Robots ◽  
Quality Indices ◽  
Motion Generation ◽  
Workspace Analysis ◽  
The Relationship

The study of the relationship between the desired system dynamics and the actuation wrench producing those dynamics is important for robotic system analysis. For traditionally actuated robots, the quality indices of dexterity and manipulability quantify this relationship. However, for unilaterally actuated robots (UARs), such as grasping hands and cable-driven parallel robots (CDPRs), these indices cannot be applied due to the unilateral actuation constraint. In this paper, the quality indices of unilateral dexterity (UD) and unilateral maximum force amplification (UMFA) are established for UARs with arbitrary number of actuators. It is shown that these quality indices provide task-independent quantifications of the physical properties of robustness and force amplification for UARs, and they can measure the mechanism’s capability both in singular and nonsingular poses. With these indices, manipulability ellipsoid-derived measures can be applied to arbitrary UARs. The significance of the quality indices for robot synthesis and motion generation analysis is illustrated through two case studies: a five-fingered grasp selection problem and the workspace analysis of a spatial CDPR.

The Manta and the Kanuk: Novel 4-DOF Parallel Mechanisms for Industrial Handling

1999 ◽  
Author(s):  
Luc H. Rolland
Keyword(s):  
Parallel Mechanism ◽  
Kinematic Chain ◽  
Parallel Robot ◽  
Chain Structure ◽  
Parallel Robots ◽  
Parallel Mechanisms ◽  
End Effector ◽  
Low Mass ◽  
Loading And Unloading ◽  
Very High

Abstract Two novel 4-DOF very fast parallel robots were designed. This paper introduces the new parallel mechanism designs which are named the Manta and the Kanuk. In order to reduce manipulator overall costs, the actuator and encoder numbers are minimized to the exact effective degrees-of-freedoms (DOF) which is usually not the case in most parallel robot designs. The robots allow end-effector displacements along the three Cartesian translations and one platform transversal rotation. The two remaining rotations are blocked by the intrinsic mechanical structure including the rotation along the platform normal which is always limited in range. The main advantages are high stiffness through the multiple kinematic chain structure which allow for low mass designs. Moreover, they feature simple mechanical construction. Thus, it shall be possible to achieve very high throughput since high accelerations are feasible. To circumvent the known workspace limitations, the actuators were selected to be prismatic along linear axes. The applications are automated warehouse manipulation, mediatheque manipulation, machine tool tool changers, loading and unloading.

Investigations on the principle of full decoupling and type synthesis of 2R1T and 2R parallel mechanisms

2019 ◽  
Vol 43 (2) ◽  
pp. 263-271 ◽  
Author(s):  
Yundou Xu ◽  
Bei Wang ◽  
Zhifeng Wang ◽  
Yun Zhao ◽  
Wenlan Liu ◽  
...  
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Parallel Mechanisms ◽  
Type Synthesis ◽  
Rotational Degrees Of Freedom ◽  
The Relationship

Based on the relationship between constraint wrenches and rotational axes, the principle of full decoupling of two rotational degrees of freedom (DOFs) for a two-rotation and one-translation (2R1T) parallel mechanism and two-rotation (2R) parallel mechanism with three supporting branches is systematically analyzed. Two conditions for full decoupling of two rotational DOFs of such mechanisms are obtained. The relationship between the two rotational axes of the parallel mechanisms is classified into two cases: intersecting and different. Next, based on the two conditions, type synthesis of the 2R1T and 2R parallel mechanisms with fully decoupled two rotational DOFs is carried out. A series of novel 2R1T and 2R parallel mechanisms with fully decoupled two rotational DOFs are obtained, such as RPU–UPR–RPR. Several of these mechanisms contain only eight single-DOF passive joints, one fewer than in existing mechanisms of this type, and thus have broad applications.

The Realization of Desired Stiffness of Parallel Mechanism by Adding Redundantly-Actuated Limbs

2017 ◽  
Author(s):  
Shunzhou Huang ◽  
Jue Yu ◽  
Hao Wang ◽  
Yong Zhao ◽  
Xinmin Lai
Keyword(s):  
Parallel Mechanism ◽  
Parallel Manipulators ◽  
Stewart Platform ◽  
Industrial Applications ◽  
Parallel Mechanisms ◽  
Normal Stiffness ◽  
Stiffness Properties ◽  
Mirror Milling ◽  
Redundantly Actuated ◽  
Mapping Models

Stiffness performance is of importance for the use of parallel manipulators in the industrial applications. For this consideration, this paper proposes to realize the desired stiffness properties of parallel mechanism by adding redundantly-actuated limbs. Based on the stiffness mapping models of both the full-DOF and limited-DOF parallel mechanisms, the stiffness variation rules when redundant limbs is introduced into the mechanism are discussed. Moreover, an algorithm for designing the types and configurations of redundant limbs is studied. Two cases are investigated to validate the presented approach. One is about the stiffness decoupling of the Stewart platform, the other is focused on the enhancement of normal stiffness of a Tricept supporting mechanism used in a mirror milling machine designed by us. The result shows that the stiffness performance of Stewart platform can be decoupled when adding six redundantly-actuated limbs that are symmetric with the original active limbs. Besides, the normal stiffness of Tricept mechanism can be enhanced significantly by transforming the passive UP chain to be a redundant actuated chain.

Effects of Orientation Angles on the Singularity-Free Workspace and Orientation Optimization of the Gough–Stewart Platform

2009 ◽  
Vol 2 (1) ◽  
Author(s):  
Qimi Jiang ◽  
Clément M. Gosselin
Keyword(s):  
Stewart Platform ◽  
Robot Design ◽  
Parallel Mechanisms ◽  
Base Plane ◽  
Optimal Orientation ◽  
Reference Orientation ◽  
Global Optimal ◽  
Orientation Optimization

The singularity-free workspace of parallel mechanisms is highly desirable in a context of robot design. This work focuses on analyzing the effects of the orientation angles on the singularity-free workspace of the Gough–Stewart platform in order to determine the optimal orientation. In any orientation with ϕ=θ=0 deg and ψ≠±90 deg, the singularity surface becomes a plane coinciding with the base plane. Hence, an analytic algorithm is presented in this work to determine the singularity-free workspace. The results show that the singularity-free workspace in some orientations can be larger than that in the reference orientation with ϕ=θ=ψ=0 deg. However, the global optimal orientation is difficult to determine. Only an approximate optimal orientation is available. The results obtained can be applied to the design or parameter setup of the Gough–Stewart platform.

Sliding Mode Set-Point Control of a Three-DOF Cable-Suspended Parallel Robot With Uncertain Mass and Disturbances

2019 ◽  
Author(s):  
Ping Ren ◽  
Xu Sheng
Keyword(s):  
Sliding Mode ◽  
Sufficient Conditions ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Parallel Mechanisms ◽  
Set Point ◽  
Point Motion ◽  
Actuation Scheme ◽  
Three Degree Of Freedom ◽  
The Relationship

Abstract Cable-Suspended Parallel Robots (CSPRs) utilize winches and cables as the actuation scheme instead of rigid links, which renders them advantages of both parallel mechanisms and cable mechanisms. In this paper, a robust sliding mode controller was designed for a three-degree-of-freedom CSPR with uncertain end-effector mass and external disturbances. To control the motions of CSPRs is usually challenging due to the unidirectional constraints of cable tensions. Based on interval analysis, a set of analytical inequalities is obtained which establish the relationship between the cables’ tension constraints and the controller parameters. The sufficient conditions of the controller parameters satisfying the constraints are obtained for the set-point motion subject to uncertainties. Numerical simulations are presented to verify the effectiveness of the proposed approach.

GEOMETRIC OPTIMIZATION OF PLANAR 3-RPR PARALLEL MECHANISMS

2007 ◽  
Vol 31 (4) ◽  
pp. 457-468 ◽  
Author(s):  
Qimi Jiang ◽  
Clément M. Gosselin
Keyword(s):  
Equilateral Triangle ◽  
Unit Area ◽  
Geometric Optimization ◽  
Parallel Mechanisms ◽  
Leg Length ◽  
Simple Singularity ◽  
Maximal Singularity ◽  
Important Concern ◽  
Singularity Locus ◽  
Similar Triangles

To pursue the maximal singularity-free workspace of parallel mechanisms is a very important concern for robot designers. This paper focuses on the case of planar 3-RPR parallel mechanisms. First, a relatively simple singularity equation of any point on the platform is derived. The obtained singularity equation shows that the singularity locus of any point on the platform is a circle of the same size, as long as the base and the platform are similar triangles. Furthermore, the three centres of the workspace circles lie exactly on the singularity circle. With these useful observations, the singularity-free workspace as well as the maximal leg length ranges can be determined. For a base of unit area, it is found that robots with equilateral triangle base and platform can obtain the maximal singularity-free workspace. Three case studies demonstrate this observation. Finally, a procedure for this kind of robot geometric design is provided.

Sign in / Sign up

Export Citation Format

Share Document