scholarly journals Collision-free workspace of parallel mechanisms based on an interval analysis approach

Robotica ◽  
2016 ◽  
Vol 35 (8) ◽  
pp. 1747-1760 ◽  
Author(s):  
MohammadHadi FarzanehKaloorazi ◽  
Mehdi Tale Masouleh ◽  
Stéphane Caro
Keyword(s):  
Interval Analysis ◽  
Parallel Mechanism ◽  
Spherical Shape ◽  
Stewart Platform ◽  
Analysis Approach ◽  
Parallel Mechanisms ◽  
Planar Case ◽  
End Effector ◽  
Mechanical Interference

SUMMARYThis paper proposes an interval-based approach in order to obtain the obstacle-free workspace of parallel mechanisms containing one prismatic actuated joint per limb, which connects the base to the end-effector. This approach is represented through two cases studies, namely a 3-RPR planar parallel mechanism and the so-called 6-DOF Gough–Stewart platform. Three main features of the obstacle-free workspace are taken into account: mechanical stroke of actuators, collision between limbs and obstacles and limb interference. In this paper, a circle(planar case)/spherical(spatial case) shaped obstacle is considered and its mechanical interference with limbs and edges of the end-effector is analyzed. It should be noted that considering a circle/spherical shape would not degrade the generality of the problem, since any kind of obstacle could be replaced by its circumscribed circle/sphere. Two illustrative examples are given to highlight the contributions of the paper.

scholarly journals Calibration Method for a Parallel Mechanism Type Machine Tool by Response Surface Methodology –Consideration via Simulation on a Stewart Platform Mechanism–

2010 ◽  
Vol 4 (4) ◽  
pp. 355-363 ◽  
Author(s):  
Hiroshi Yachi ◽  
◽  
Hiroshi Tachiya
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Parallel Mechanism ◽  
Measurement Data ◽  
Calibration Method ◽  
Stewart Platform ◽  
Parallel Mechanisms ◽  
Data Set ◽  
Efficient Data ◽  
Efficient Measurement

This paper proposes a calibration method for parallel mechanisms usingResponse Surface Methodology. This method is a statistical approach to estimating an unknown input-output relationship using a small set of efficient data collected on an intended system. Although identifying locations causing positional errors in a parallel mechanism and precisely measuring the position and posture of the output point are difficult, the proposed calibration method based onResponse Surface Methodologyaims to compensate for positional and postural errors, without indentifying the locations causing these errors, by using a small yet efficient measurement data set. This study analyzes the effectiveness of the method we propose by applying it to a Stewart platform, which is a typical spatial 6-DOF parallel mechanism.

Relevance and Transferability for Parallel Mechanisms With Reconfigurable Platforms

2019 ◽  
Vol 11 (3) ◽  
Author(s):  
Xi Kang ◽  
Jian S. Dai
Keyword(s):  
System Theory ◽  
Parallel Mechanism ◽  
Geometric Model ◽  
Parallel Mechanisms ◽  
End Effector ◽  
Kinematic Coupling ◽  
Reconfigurable Platforms ◽  
Reconfigurable Platform

The parallel mechanism with a reconfigurable platform retains all advantages of parallel mechanisms and provides additional functions by virtue of the reconfigurable platform, leading to kinematic coupling between limbs that restricts development of the mechanism. This paper aims at dealing with kinematic coupling between limbs by investigating the transferability of limb constraints and their degrees of relevance to the platform constraints based on the geometric model of the mechanism. The paper applies screw-system theory to verifying the degree of relevance between limb constraint wrenches and platform constraint wrenches, and reveals the transferability of limb constraints, to obtain the final resultant wrenches and twists of the end effector. The proposed method is extended to parallel mechanisms with planar n-bar reconfigurable platforms, spherical n-bar reconfigurable platforms, and other spatial reconfigurable platforms and lends itself to a way of studying a parallel mechanism with a reconfigurable platform.

The Mechanics of Parallel Mechanisms and Walking Machines

1994 ◽  
Vol 208 (6) ◽  
pp. 367-377 ◽  
Author(s):  
S J Zhang ◽  
D J Sanger ◽  
D Howard
Keyword(s):  
Parallel Mechanism ◽  
Virtual Work ◽  
The Body ◽  
Position Vector ◽  
Parallel Mechanisms ◽  
Active Joint ◽  
End Effector ◽  
Walking Machine ◽  
Walking Machines ◽  
Fixed Base

A parallel mechanism is one whose links and joints form two or more serially connected chains which join the fixed base and the end effector The mechanism of a multi-legged walking machine can be considered as a parallel mechanism whose base is not fixed and whose configuration changes during different phases of its gait. This paper presents methods for analysing the mechanics of parallel mechanisms and walking machines using vector and screw algebra Firstly, displacement analysis is covered; this includes general methods for deriving the position vector of any joint in any leg and for calculating the active joint displacements in any leg. Secondly, velocity analysis is covered which tackles the problem of calculating active joint velocities given the velocity, position and the orientation of the body and the positions of the feet. Thirdly, the static analysis of these classes of mechanisms using the principle of virtual work and screw algebra is given. Expressions are derived for the actuator forces and torques required to balance a given end effector (or body) wrench and, in the case of a walking machine, the ground reactions at the feet. Numerical examples are given to demonstrate the application of these methods.

A Quasi-Static Model for Planar Compliant Parallel Mechanisms

2009 ◽  
Vol 1 (2) ◽  
Author(s):  
Cyril Quennouelle ◽  
Clément Gosselin
Keyword(s):  
Parallel Mechanism ◽  
Applied Load ◽  
Jacobian Matrix ◽  
Static Model ◽  
Parallel Mechanisms ◽  
Compliance Matrix ◽  
End Effector ◽  
Kinematic Constraints ◽  
Compliant Parallel Mechanism ◽  
External Loads

In this paper, the mobility, the kinematic constraints, the pose of the end-effector, and the static constraints that lead to the kinematostatic model of a compliant parallel mechanism are introduced. A formulation is then provided for its instantaneous variation—the quasi-static model. This new model allows the calculation of the variation in the pose as a linear function of the motion of the actuators and the variation in the external loads through two new matrices: the compliant Jacobian matrix and the Cartesian compliance matrix that give a simple and meaningful formulation of the model of the mechanism. Finally, a simple application to a planar four-bar mechanism is presented to illustrate the use of this model and the new possibilities that it opens, notably the study of the kinematics for any range of applied load.

The Manta and the Kanuk: Novel 4-DOF Parallel Mechanisms for Industrial Handling

1999 ◽  
Author(s):  
Luc H. Rolland
Keyword(s):  
Parallel Mechanism ◽  
Kinematic Chain ◽  
Parallel Robot ◽  
Chain Structure ◽  
Parallel Robots ◽  
Parallel Mechanisms ◽  
End Effector ◽  
Low Mass ◽  
Loading And Unloading ◽  
Very High

Abstract Two novel 4-DOF very fast parallel robots were designed. This paper introduces the new parallel mechanism designs which are named the Manta and the Kanuk. In order to reduce manipulator overall costs, the actuator and encoder numbers are minimized to the exact effective degrees-of-freedoms (DOF) which is usually not the case in most parallel robot designs. The robots allow end-effector displacements along the three Cartesian translations and one platform transversal rotation. The two remaining rotations are blocked by the intrinsic mechanical structure including the rotation along the platform normal which is always limited in range. The main advantages are high stiffness through the multiple kinematic chain structure which allow for low mass designs. Moreover, they feature simple mechanical construction. Thus, it shall be possible to achieve very high throughput since high accelerations are feasible. To circumvent the known workspace limitations, the actuators were selected to be prismatic along linear axes. The applications are automated warehouse manipulation, mediatheque manipulation, machine tool tool changers, loading and unloading.

The Maximal Singularity-Free Workspace of the Gough–Stewart Platform for a Given Orientation

2008 ◽  
Vol 130 (11) ◽  
Author(s):  
Qimi Jiang ◽  
Clément M. Gosselin
Keyword(s):  
Case Studies ◽  
Parallel Mechanism ◽  
Stewart Platform ◽  
Parallel Robots ◽  
Analytic Method ◽  
Robot Design ◽  
Parallel Mechanisms ◽  
Leg Length ◽  
Maximal Singularity ◽  
The Relationship

The maximal singularity-free workspace of parallel mechanisms is a desirable criterion in robot design. However, for a 6DOF parallel mechanism, it is very difficult to find an analytic method to determine the maximal singularity-free workspace around a prescribed point for a given orientation. Hence, a numerical algorithm is presented in this paper to compute the maximal singularity-free workspace as well as the corresponding leg length ranges of the Gough–Stewart platform. This algorithm is based on the relationship between the maximal singularity-free workspace and the singularity surface. Case studies with different orientations are performed to demonstrate the presented algorithm. The obtained results can be applied to the geometric design or parameter (leg length) setup of this type of parallel robots.

The Realization of Desired Stiffness of Parallel Mechanism by Adding Redundantly-Actuated Limbs

2017 ◽  
Author(s):  
Shunzhou Huang ◽  
Jue Yu ◽  
Hao Wang ◽  
Yong Zhao ◽  
Xinmin Lai
Keyword(s):  
Parallel Mechanism ◽  
Parallel Manipulators ◽  
Stewart Platform ◽  
Industrial Applications ◽  
Parallel Mechanisms ◽  
Normal Stiffness ◽  
Stiffness Properties ◽  
Mirror Milling ◽  
Redundantly Actuated ◽  
Mapping Models

Stiffness performance is of importance for the use of parallel manipulators in the industrial applications. For this consideration, this paper proposes to realize the desired stiffness properties of parallel mechanism by adding redundantly-actuated limbs. Based on the stiffness mapping models of both the full-DOF and limited-DOF parallel mechanisms, the stiffness variation rules when redundant limbs is introduced into the mechanism are discussed. Moreover, an algorithm for designing the types and configurations of redundant limbs is studied. Two cases are investigated to validate the presented approach. One is about the stiffness decoupling of the Stewart platform, the other is focused on the enhancement of normal stiffness of a Tricept supporting mechanism used in a mirror milling machine designed by us. The result shows that the stiffness performance of Stewart platform can be decoupled when adding six redundantly-actuated limbs that are symmetric with the original active limbs. Besides, the normal stiffness of Tricept mechanism can be enhanced significantly by transforming the passive UP chain to be a redundant actuated chain.

Kinestatic Control: A Novel Theory for Simultaneously Regulating Force and Displacement

1991 ◽  
Vol 113 (4) ◽  
pp. 508-515 ◽  
Author(s):  
M. Griffis ◽  
J. Duffy
Keyword(s):  
Parallel Mechanism ◽  
Stewart Platform ◽  
Positive Definite ◽  
Rigid Bodies ◽  
Inner Product ◽  
General State ◽  
End Effector ◽  
Simultaneous Control ◽  
Novel Theory ◽  
Invariant Properties

A new theory for the simultaneous control of force and displacement for a partially constrained end-effector is established based upon the general spatial stiffness of the manipulator. In general, the spatial stiffness of a compliant coupling that connects a pair of rigid bodies is used to map a small twist between the bodies into the corresponding interactive wrench. This mapping is based upon a firm geometrical foundation and establishes a positive-definite inner product (elliptic metric) that decomposes a general twist into a twist of freedom and a twist of compliance. A study of the invariant properties of this mapping leads to the discovery of what are defined as the eigen-screws of stiffness. Further, the spatial stiffness of a compliant coupling is modeled by theoretically replacing the coupling with a passive Stewart Platform-type parallel mechanism. It is important to recognize that this model does not depend upon the existence of a center-of-compliance. In fact, it describes a general state of spatial stiffness between any two rigid bodies. The culmination of these finding yields a practical and meaningful theory of Kinestatic Control, viz., the simultaneous regulation of force and displacement solely via the control of displacement.

Optimal trajectory planning considering optimal torque distribution of redundantly actuated parallel mechanism

2018 ◽  
Vol 232 (23) ◽  
pp. 4410-4419 ◽  
Author(s):  
Sumin Park ◽  
Jongwon Kim ◽  
Giuk Lee
Keyword(s):  
Parallel Mechanism ◽  
Optimization Procedure ◽  
Optimal Operation ◽  
Operation Planning ◽  
Parallel Mechanisms ◽  
Planning Stage ◽  
End Effector ◽  
Torque Distribution ◽  
Redundantly Actuated ◽  
Two Stages

Previous studies on the optimal operation planning of redundantly actuated parallel mechanisms have focused on optimal torque distribution for a predefined trajectory. However, the optimized result obtained for a predefined trajectory cannot guarantee an optimal operation plan, because the torque distribution ability of a redundantly actuated parallel mechanism is highly dependent on the shape of the end-effector trajectory. Therefore, we can expect the redundantly actuated parallel mechanism performance to be enhanced when both the trajectory and torque distribution are optimized during the optimal operation planning stage. We propose a novel redundantly actuated parallel mechanism optimization procedure that can optimize both the end-effector trajectory and torque distribution. The proposed procedure is composed of two stages of optimizers, i.e. upper- and lower-level optimizers that generate the end-effector trajectory and distribute the torques along the generated trajectory, respectively. Composition of these two stages of the optimization procedure allows optimization of both the trajectory and torque distribution, despite the correlation between them. The proposed optimization procedure is simulated using two types of cost functions. All the simulation results show that the proposed procedure facilitates optimization of the end-effector trajectory and the torque distribution concurrently. Also, the cost function value is minimized to a greater extent than in the result with the optimal torque distribution along the initial trajectory.

Closed-Form Direct Position Analysis of a 5–5 Parallel Mechanism

1993 ◽  
Vol 115 (3) ◽  
pp. 515-521 ◽  
Author(s):  
C. Innocenti ◽  
V. Parenti-Castelli
Keyword(s):  
Closed Form ◽  
Parallel Mechanism ◽  
General Feature ◽  
Polynomial Equation ◽  
Stewart Platform ◽  
Parallel Mechanisms ◽  
Complex Field ◽  
Output Link ◽  
Degree Polynomial ◽  
Displacement Analysis

The paper presents the closed form direct displacement analysis for a class of Stewart platform-type parallel mechanisms whose general feature consists of six legs which meet five distinct points both in the base and in the movable output link. Out of the two possible arrangements, only one is here analyzed in detail. Given a set of actuator displacements the analysis provides all the possible locations of the platform relative to the base. The analysis results in a 40th degree polynomial equation in one unknown. The roots of the equation provide in the complex field forty closures of the mechanism. This new result has been numerically verified by the inverse displacement analysis.

Sign in / Sign up

Export Citation Format

Share Document