Film Cooling in a Separated Flow Field on a Novel Lightweight Turbine Blade

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Yoji Okita ◽  
Chiyuki Nakamata ◽  
Masaya Kumada ◽  
Masahiro Ikeda
Keyword(s):  
Flow Field ◽  
Turbine Blade ◽  
Film Cooling ◽  
Separation Bubble ◽  
Separated Flow ◽  
Suction Side ◽  
Pressure Side ◽  
Effective Measure ◽  
Cooling Performance ◽  
Recirculation Flow

The primary contribution of this research is to clarify the feasibility of a novel lightweight turbine blade with internal and external cooling, which is invented, aiming at drastic reduction in weight. With a considerably thinner airfoil, an extensive separation bubble is formed on the pressure side, and film cooling performance in such a flow field has to be investigated. Experimental results with a curved duct setup, which simulates the flow field around the proposed airfoil, show that a film cooling is still an effective measure of cooling even in the vastly separated region, and it behaves quite similarly to the conventional correlation, except for lower blowing ratios, where the thermal field is strongly affected by the intense recirculation flow. Comparisons between the experimental and numerical results verify that an affordable Reynolds-averaged Navier–Stokes simulation is useful to investigate the detailed physics of this flow field. With the numerical modeling, a cooling performance of the proposed blade under a typical engine operating condition is simulated, and the metal temperatures of the blade are also predicted with a fluid-solid conjugate calculation. The resultant thermal distribution in the airfoil suggests that the trailing edge portion is inevitably most critical in the temperature, and also a considerable thermal gradient across the blade is induced. Thermal profile, however, is partly recovered with some of the film coolant being bypassed from the pressure side to the suction side.

Film Cooling in a Separated Flow Field on a Novel Lightweight Turbine Blade

2008 ◽  
Author(s):  
Yoji Okita ◽  
Chiyuki Nakamata ◽  
Masaya Kumada ◽  
Masahiro Ikeda
Keyword(s):  
Flow Field ◽  
Turbine Blade ◽  
Film Cooling ◽  
Separation Bubble ◽  
Separated Flow ◽  
Suction Side ◽  
Pressure Side ◽  
Effective Measure ◽  
Cooling Performance ◽  
Recirculation Flow

The primary contribution of this research is to clarify the feasibility of a novel lightweight turbine blade with internal and external cooling, which is invented aiming at drastic reduction of weight. With a considerably thinner airfoil, an extensive separation bubble is formed on the pressure side and film cooling performance in such a flow field has to be investigated. Experimental results with a curved duct setup, which simulates the flow field around the proposed airfoil, show that a film cooling is still an effective measure of cooling even in the vastly separated region and it behaves quite similarly to the conventional correlation except for lower blowing ratios where the thermal field is strongly affected by the intense recirculation flow. Comparisons between the experimental and numerical results verify that an affordable RANS simulation is useful to investigate the detailed physics of this flow field. With the numerical modeling, a cooling performance of the proposed blade under a typical engine operating condition is simulated and the metal temperatures of the blade are also predicted with a fluid-solid conjugate calculation. The resultant thermal distribution in the airfoil suggests that the trailing edge portion is inevitably most critical in the temperature and also a considerable thermal gradient across the blade is induced. Thermal profile, however, is partly recovered with some of the film coolant being bypassed from the pressure side to the suction side.

Numerical simulation of swirling flow effect on the first stage vane film cooling distribution

2016 ◽  
Vol 07 (03) ◽  
pp. 1650031
Author(s):  
Hong Yin
Keyword(s):  
Flow Field ◽  
Film Cooling ◽  
Swirling Flow ◽  
Cooling System ◽  
Leading Edge ◽  
Suction Side ◽  
Local Area ◽  
Swirl Flow ◽  
Flow Effect ◽  
Recirculation Flow

In advanced gas turbine technology, lean premixed combustion is an effective strategy to reduce peak temperature and thus, NO[Formula: see text] emissions. The swirler is adopted to establish recirculation flow zone, enhancing mixing and stabilizing the flame. Therefore, the swirling flow is dominant in the combustor flow field and has impact on the vane. This paper mainly investigates the swirling flow effect on the turbine first stage vane cooling system by conducting a group of numerical simulations. Firstly, the numerical methods of turbulence modeling using RANS and LES are compared. The computational model of one single swirl flow field is considered. Both the RANS and LES results give reasonable recirculation zone shape. When comparing the velocity distribution, the RANS results generally match the experimental data but fail to at some local area. The LES modeling gives better results and more detailed unsteady flow field. In the second step, the RANS modeling is incorporated to investigate the vane film cooling performance under the swirling inflow boundary condition. According to the numerical results, the leading edge film cooling is largely altered by the swirling flow, especially for the swirl core-leading edge aligned case. Compared to the pressure side, the suction side film cooling is more sensitive to the swirling flow. Locally, the film cooling jet is lifted and turned by the strong swirling flow.

Cooling Effectiveness on Film Cooled Turbine Blades

2001 ◽  
Author(s):  
M. Derrar ◽  
J. Nagler ◽  
W. W. Koschel
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Suction Side ◽  
Experimental Simulation ◽  
Flow Conditions ◽  
Cooling Effectiveness ◽  
Boundary Interaction ◽  
Simultaneous Modeling

Abstract This paper presents experiments on the cooling effectiveness obtained for two different injection locations on the suction side of a turbine blade at transonic flow conditions. Previous results of a computational analysis and flow visualization indicated that a separation bubble is present on the suction side at a location x/L = 0.43 and the location x/L = 0.575 corresponds to a shock-boundary interaction zone [9]. The scientific interest is primarily focused on the realization of high film cooling efficiencies and its relevant parameters under these flow conditions. Streamwise aligned as well as inclined angled film coolant hole configurations have been investigated for each location. Due to the high number of interacting parameters the experimental simulation of turbine blade film cooling is extremely complex, which can only be solved by a simultaneous modeling using the experimentally measured results. Test rig, instrumentation and data analysis are described in detail. The goal of the investigations is to determine the optimum location of the film coolant injection.

Surface Curvature Effects on Film Cooling Performance for Shaped Holes on a Model Turbine Blade

2020 ◽  
Vol 142 (11) ◽  
Author(s):  
Jacob D. Moore ◽  
Christopher Yoon ◽  
David G. Bogard
Keyword(s):  
Flat Plate ◽  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbines ◽  
Convex Surface ◽  
Adverse Pressure Gradient ◽  
Suction Side ◽  
Surface Curvature ◽  
Cooling Performance ◽  
Curvature Effects

Abstract Surface curvature has been shown to have significant effects on the film cooling performance of round holes, but the literature include few studies of its effects on shaped holes despite their prevalence in gas turbines. Experiments were performed using two rows of holes placed on the suction side of a scaled-up turbine blade in a low Mach number linear cascade wind tunnel with low freestream turbulence. The rows were placed in regions of high and low convex surface curvature. Geometries and flow conditions for the rows were matched to those from previous flat plate studies. Comparison of the adiabatic effectiveness results from the high curvature and flat plate rows revealed the same trends as those in the literature using round holes, with increased performance for the high curvature row at lower blowing ratios and the opposite at higher ones. The low curvature row had similar performance to the flat plate row at lower blowing ratios, suggesting the mild convex curvature had little beneficial effect. At higher blowing ratios, the low curvature row had inferior performance, which was attributed to the local freestream adverse pressure gradient that generated additional turbulence, promoting jet-to-mainstream mixing and decreasing performance.

An Experimental Investigation of Flow Characteristics Downstream of Discrete Film Cooling Holes on Turbine Blade Leading Edge

2011 ◽  
Vol 383-390 ◽  
pp. 5553-5560
Author(s):  
Shao Hua Li ◽  
Hong Wei Qu ◽  
Mei Li Wang ◽  
Ting Ting Guo
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Suction Side ◽  
Wall Region ◽  
Pressure Side ◽  
Blowing Ratio ◽  
Curvature Gradient ◽  
Film Cooling Holes

The gas turbine blade was studied on the condition that the mainstream velocity was 10m/s and the Renolds number based on the chord length of the blade was 160000.The Hot-film anemometer was used to measure the two-dimension speed distribution along the downstream of the film cooling holes on the suction side and the pressure side. The conclusions are as follows: When the blowing ratio of the suction side and the pressure side increasing, the the mainstream and the jet injection mixing center raising. Entrainment flow occurs at the position where the blade surface with great curvature gradient, simultaneously the mixing flow has a wicked adhere to the wall. The velocity gradient of the u direction that on the suction side increase obviously, also the level of the wall adherence is better than the pressure side. With the x/d increasing, the velocity u that on the pressure side gradually become irregularly, also the secondary flow emerged near the wall region where the curvature is great. The blowing ratio on the suction side has a little influence on velocity v than that on the pressure side.

Film-Cooling on a Gas Turbine Blade Pressure Side or Suction Side With Compound Angle Shaped Holes

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Zhihong Gao ◽  
Diganta P. Narzary ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Suction Side ◽  
Pressure Side ◽  
Blade Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Surface ◽  
Compound Angle

The film-cooling effectiveness on the surface of a high pressure turbine blade is measured using the pressure sensitive paint technique. Compound angle laidback fan-shaped holes are used to cool the blade surface with four rows on the pressure side and two rows on the suction side. The coolant injects to one side of the blade, either pressure side or suction side. The presence of wake due to the upstream vanes is simulated by placing a periodic set of rods upstream of the test blade. The wake rods can be clocked by changing their stationary positions to simulate progressing wakes. The effect of wakes is recorded at four phase locations along the pitchwise direction. The freestream Reynolds number, based on the axial chord length and the exit velocity, is 750,000. The inlet and exit Mach numbers are 0.27 and 0.44, respectively, resulting in a pressure ratio of 1.14. Five average blowing ratios ranging from 0.4 to 1.5 are tested. Results reveal that the tip-leakage vortices and endwall vortices sweep the coolant on the suction side to the midspan region. The compound angle laidback fan-shaped holes produce a good film coverage on the suction side except for the regions affected by the secondary vortices. Due to the concave surface, the coolant trace is short and the effectiveness level is low on the pressure surface. However, the pressure side acquires a relatively uniform film coverage with the multiple rows of cooling holes. The film-cooling effectiveness increases with the increasing average blowing ratio for either side of coolant ejection. The presence of stationary upstream wake results in lower film-cooling effectiveness on the blade surface. The compound angle shaped holes outperform the compound angle cylindrical holes by the elevated film-cooling effectiveness, particularly at higher blowing ratios.

A study for the film cooling performance on the turbine blade suction side tip region under rotating conditions

2019 ◽  
Vol 138 ◽  
pp. 483-495
Author(s):  
Haichao Wang ◽  
Zhi Tao ◽  
Zhiyu Zhou ◽  
Huimin Zhou ◽  
Yiwen Ma ◽  
...  
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Suction Side ◽  
Cooling Performance

Experimental Study of Sister Hole Film Cooling Performance in a Rotating Flat Plate Model

2015 ◽  
Author(s):  
Hong Wu ◽  
Huichuan Cheng ◽  
Yulong Li ◽  
Shuiting Ding
Keyword(s):  
Reynolds Number ◽  
Flat Plate ◽  
Rotation Number ◽  
Film Cooling ◽  
Suction Side ◽  
Pressure Side ◽  
Plate Model ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

Film cooling performance of a sister hole was investigated in a flat plate model by applying Thermochromic Liquid Crystal (TLC) technique under the stationary and rotating conditions. The flat plate model is installed in the test section. The sister hole include one main hole and two additional side holes with the smaller diameter in the spanwise direction. The diameter of the main hole is 4 mm and the injection angle is 30°. The density ratio of coolant to mainstream is 1.05. The Reynolds number (ReD) based on the velocity of mainstream and the diameter of the main hole are 2300, 3400 and 4500. Four rotational speeds of 200, 400, 600 and 800 rpm are conducted on both pressure side (trailing wall) and suction side (leading wall) with the blowing ratio varying from 0.14 to 3.5. The effects of blowing ratio, Reynolds number (ReD) and rotation number are mainly analyzed according to film coverage and film cooling effectiveness. The results show that the film performance firstly increases then decreases with the rising of blowing ratio, the optimal blowing ratio is about M=0.5. The film cooling performance is improved with higher Reynolds number (ReD). Under the rotation condition, the film trajectory has an obvious centrifugal deflection which can be enhanced by higher rotation number on the pressure side, and the film deflection moves a little centripetally on the suction side. The film cooling effectiveness on the suction side increases with the rising of rotation number and it is higher than that on the pressure side.

Experimental Investigations of the Film Cooling Performance of a Micro-Tangential-Jet Scheme on a Gas Turbine Vane: Part 1 — Effectiveness

2012 ◽  
Author(s):  
O. Hassan ◽  
I. Hassan
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Density Ratio ◽  
Suction Side ◽  
Experimental Investigations ◽  
Stream Velocity ◽  
Pressure Side ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Turbine Vane

This paper presents experimental investigations of the film cooling effectiveness performance of a Micro-Tangential-Jet (MTJ) Film cooling scheme on a gas turbine vane using transient Thermochromic Liquid Crystal (TLC) technique. The MTJ scheme is a micro-shaped scheme designed so that the secondary jet is supplied tangentially to the vane surface. The scheme combines the benefits of micro jets and tangential injection. The film cooling performance of one row of holes on both pressure and suction sides were investigated at a blowing ratio ranging from 0.5 to 1.5 on the pressure side and 0.25 to 0.625 on the suction side. The average density ratio during the investigations was 0.93, and the Reynolds Number was 1.4E+5, based on the free stream velocity and the main duct hydraulic diameter. The pitch to diameter ratio of the cooling holes is 5 on the pressure side and 6.5 on the suction side. The turbulence intensity during all investigations was 8.5%. Minor changes in the Mach number distribution around the airfoil surface were observed due to the presence of the MTJ scheme, compared with the case with no MTJ scheme. The investigations showed great film cooling performance for the MTJ scheme, high effectiveness values, and excellent lateral jet spreading. A 2-D coolant film was observed in the results, which is a characteristic of the continuous slot schemes only. The presence of this 2-D film layer helps minimize the rate of mixing between the main and coolant streams and provides uniform thermal loads on the surface. Furthermore, it was noticed that the rate of effectiveness decay on the suction side was less than that on the pressure side, while the lateral jet spreading on the pressure side was better than that of the suction side. The main disadvantage of the MTJ scheme is the increased pressure drop.

Film-Cooling on a Gas Turbine Blade Pressure Side or Suction Side With Compound Angle Shaped Holes

2007 ◽  
Author(s):  
Zhihong Gao ◽  
Diganta P. Narzary ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Suction Side ◽  
Steady Increase ◽  
Pressure Side ◽  
Wake Effect ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Compound Angle

The film cooling effectiveness on the surface of a high pressure turbine blade is measured using the Pressure Sensitive Paint (PSP). Four rows of fan-shaped, laid-back compound angled cooling holes are distributed on the pressure side while two such rows are provided on the suction side of the blade. The coolant is only injected to either the pressure side or suction side of the blade at five average blowing ratios from 0.4 to 1.5. Presence of wake due to upstream vanes is simulated by placing a periodic set of rods upstream of the test blade. The wake rods can be clocked by changing their stationary positions to simulate a progressing wake. Effect of wake is recorded at four phase locations with equal intervals along the pitch-wise direction. The free stream Reynolds number, based on the axial chord length and the exit velocity, is 750,000 and the inlet and the exit Mach numbers are 0.27 and 0.44, respectively, resulting in a blade pressure ratio of 1.14. Results reveal that the tip leakage vortices and endwall vortices sweep the coolant film on the suction side to the midspan region. The fan-shaped, laid-back compound angled holes produce good coolant film coverage on the suction side except for those regions affected by the secondary vortices. Due to the concave surface, the coolant trace is short and effectiveness level is low on the pressure surface. However, the pressure side acquires relatively uniform film coverage with the design of multiple rows of cooling holes. The presence of stationary upstream wake results in lower film cooling effectiveness on the blade surface. Variation of blowing ratio from 0.4 to 1.5 shows steady increase in effectiveness on the pressure side or the suction side for a given wake rod phases locations. The compound angle shaped holes outperform the compound angle cylindrical holes by the elevated film cooling effectiveness particularly at higher blowing ratios.

Sign in / Sign up

Export Citation Format

Share Document