Effect of an Oscillating Flow Direction on Leading Edge Heat Transfer

1984 ◽  
Vol 106 (1) ◽  
pp. 222-228 ◽  
Author(s):  
M. L. Marziale ◽  
R. E. Mayle
Keyword(s):  
Heat Transfer ◽  
Strouhal Number ◽  
Large Scale ◽  
Flow Direction ◽  
Leading Edge ◽  
Periodic Variation ◽  
Scale Model ◽  
Transfer Rates ◽  
Large Scale Model ◽  
Turbulence Length

An experimental investigation was conducted to examine the effect of a periodic variation in the angle of attack on heat transfer at the leading edge of a gas turbine blade. A circular cylinder was used as a large-scale model of the leading edge region. The cylinder was placed in a wind tunnel and was oscillated rotationally about its axis. The incident flow Reynolds number and the Strouhal number of oscillation were chosen to model an actual turbine condition. Incident turbulence levels up to 4.9 percent were produced by grids placed upstream of the cylinder. The transfer rate was measured using a mass transfer technique and heat transfer rates inferred from the results. A direct comparison of the unsteady and steady results indicate that the effect is dependent on the Strouhal number, turbulence level, and the turbulence length scale, but that the largest observed effect was only a 10 percent augmentation at the nominal stagnation position.

Cooling Performance of a Narrow Impingement Channel Including the Introduction of Cross Flow Upstream of the First Hole

2003 ◽  
Author(s):  
Andrew C. Chambers ◽  
David R. H. Gillespie ◽  
Peter T. Ireland ◽  
Geoffrey M. Dailey
Keyword(s):  
Heat Transfer ◽  
Large Scale ◽  
Cooling System ◽  
Cross Flow ◽  
Scale Model ◽  
Test Technique ◽  
Turbine Blade Cooling ◽  
Turbine Cooling ◽  
Impingement Heat Transfer ◽  
Large Scale Model

Impingement channels are often used in turbine blade cooling configurations. This paper examines the heat transfer performance of a typical integrally cast impingement channel. Detailed heat transfer coefficient distributions on all heat transfer surfaces were obtained in a series of low temperature experiments carried out in a large-scale model of a turbine cooling system using liquid crystal techniques. All experiments were performed on a model of a 19-hole, low aspect ratio impingement channel. The effect of flow introduced at the inlet to the channel on the impingement heat transfer within the channel was investigated. A novel test technique has been applied to determine the effect of the initial cross flow on jet penetration. The experiments were performed at an engine representative Reynolds number of 20,000 and examined the effect of additional initial cross flow up to 10% of the total mass flow.

Experimental Measurements and Computational Predictions for an Internally Cooled Simulated Turbine Vane

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Jason E. Dees ◽  
David G. Bogard ◽  
Gustavo A. Ledezma ◽  
Gregory M. Laskowski ◽  
Anil K. Tolpadi
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Large Scale ◽  
Leading Edge ◽  
Internal Surface ◽  
Scale Model ◽  
Experimental Measurements ◽  
Internal Cooling ◽  
Internally Cooled ◽  
Computational Predictions

In this study the conjugate heat transfer effects for an internally cooled vane were studied experimentally and computationally. Experimentally, a large scale model vane was used with an internal cooling configuration characteristic of real gas turbine airfoils. The cooling configuration employed consisted of a U-bend channel for cooling the leading edge region of the airfoil and a radial channel for cooling the middle third of the vane. The thermal conductivity of the solid was specially selected so that the Biot number for the model matched typical engine conditions. This ensured that scaled nondimensional surface temperatures for the model were representative of those in the first stage of a high pressure turbine. The performance of the internal cooling circuit was quantified experimentally for internal flow Reynolds numbers ranging from 10,000 to 40,000. The external surface temperature distribution was mapped over the entire vane surface. Additional measurements, including internal surface temperature measurements as well as coolant inlet and exit temperatures, were conducted. Comparisons between the experimental measurements and computational predictions of external heat transfer coefficient are presented.

Experimental Measurements and Computational Predictions for an Internally Cooled Simulated Turbine Vane

2009 ◽  
Author(s):  
Jason E. Dees ◽  
David G. Bogard ◽  
Gustavo A. Ledezma ◽  
Gregory M. Laskowski ◽  
Anil K. Tolpadi
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Large Scale ◽  
Leading Edge ◽  
Internal Surface ◽  
Scale Model ◽  
Experimental Measurements ◽  
Internal Cooling ◽  
Internally Cooled ◽  
Computational Predictions

In this study the conjugate heat transfer effects for an internally cooled vane were studied experimentally and computationally. Experimentally, a large scale model vane was used with an internal cooling configuration characteristic of real gas turbine airfoils. The cooling configuration employed consisted of a U-bend channel for cooling the leading edge region of the airfoil and a radial channel for cooling the middle third of the vane. The thermal conductivity of the solid was specially selected so that the Biot number for the model matched typical engine conditions. This ensured that scaled non-dimensional surface temperatures for the model were representative of those in the first stage of a HPT. The performance of the internal cooling circuit was quantified experimentally for internal flow Reynolds numbers ranging from 10,000 to 40,000. The external surface temperature distribution was mapped over the entire vane surface. Additional measurements, including internal surface temperature measurements as well as coolant inlet and exit temperatures were conducted. Comparisons between the experimental measurements and computational predictions of external heat transfer coefficient are presented.

RANCANG BANGUN PERANGKAT EKSPERIMENTASI PROSES PIROLISIS BIOMASA GELOMBANG MIKRO

2013 ◽  
Vol 14 (2) ◽  
Author(s):  
Noor Fachrizal
Keyword(s):  
Large Scale ◽  
Continuous Model ◽  
Biomass Energy ◽  
Scale Model ◽  
Small Scale ◽  
Laboratory Apparatus ◽  
Liquid Form ◽  
Large Scale Model ◽  
Bio Oil ◽  
Pyrolysis Of Biomass

Biomass such as agriculture waste and urban waste are enormous potency as energy resources instead of enviromental problem. organic waste can be converted into energy in the form of liquid fuel, solid, and syngas by using of pyrolysis technique. Pyrolysis process can yield higher liquid form when the process can be drifted into fast and flash response. It can be solved by using microwave heating method. This research is started from developing an experimentation laboratory apparatus of microwave-assisted pyrolysis of biomass energy conversion system, and conducting preliminary experiments for gaining the proof that this method can be established for driving the process properly and safely. Modifying commercial oven into laboratory apparatus has been done, it works safely, and initial experiments have been carried out, process yields bio-oil and charcoal shortly, several parameters are achieved. Some further experiments are still needed for more detail parameters. Theresults may be used to design small-scale continuous model of productionsystem, which then can be developed into large-scale model that applicable for comercial use.

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Normal to the Flow

1992 ◽  
Vol 114 (4) ◽  
pp. 847-857 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
R. A. Graziani ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large-scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges that are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat transfer increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

Sign in / Sign up

Export Citation Format

Share Document