Pressurized Oil Squeeze Film Dampers

1980 ◽  
Vol 102 (1) ◽  
pp. 41-47 ◽  
Author(s):  
A. Kent Stiffler
Keyword(s):  
Design Methodology ◽  
Squeeze Film ◽  
Rigid Rotor ◽  
Squeeze Film Damper ◽  
Supply Pressure ◽  
Squeeze Film Dampers ◽  
Stiffness And Damping ◽  
Film Stiffness

A pressurized oil squeeze film damper supporting a rigid rotor mounted in antifriction bearings is investigated. Orifice and inherent feed inlets are examined, and it is shown that the clearance determines the inlet resistance for a groove or slot. The film stiffness and damping forces are determined as a function of the restrictor coefficient, rotor unbalance speed and the supply pressure using the short bearing approximation. These forces are related to the system transmissibility. A design methodology for low transmissibilities is presented.

Eccentric Operation and Blade-Loss Simulation of a Rigid Rotor Supported by an Improved Squeeze Film Damper

1995 ◽  
Vol 117 (3) ◽  
pp. 490-497 ◽  
Author(s):  
J. Y. Zhao ◽  
E. J. Hahn
Keyword(s):  
Outer Ring ◽  
Squeeze Film ◽  
Rigid Rotor ◽  
Cavitation Model ◽  
Squeeze Film Damper ◽  
Constant Stiffness ◽  
Flexible Support ◽  
Squeeze Film Dampers ◽  
Stiffness And Damping ◽  
Blade Loss

This paper outlines an improved squeeze film damper which reduces significantly the dependence of the stiffness of conventional squeeze film dampers on the vibration amplitudes. This improved damper consists of a conventional squeeze film damper with a flexibility supported outer ring. This secondary flexible support is considered to be massless, and to have a constant stiffness and damping. Assuming the short bearing approximation and the ‘π’ film cavitation model, the performances of this damper in preventing bistable operation and sub-synchronous and nonsynchronous motions are theoretically demonstrated for a rigid rotor supported on a squeeze film damper. Blade-loss simulations are carried out numerically.

Dynamical Behaviors of Hybrid Squeeze Film Damper for Rotor System Vibration Control

1995 ◽  
Author(s):  
Zhu Changsheng
Keyword(s):  
Rotor System ◽  
Squeeze Film ◽  
Radial Clearance ◽  
Rigid Rotor ◽  
Squeeze Film Damper ◽  
Damping Coefficients ◽  
Dynamical Behaviors ◽  
System Vibration ◽  
Stiffness And Damping ◽  
Film Stiffness

Abstract The behaviors of oil film stiffness and damping coefficients of the deep multi-recessed hybrid squeeze film damper (HSFD) with the orifices compensated are first analysed in this paper. The control ability of the HSFD on the rotor system vibrations is studied theoretically and experimentally with a rigid rotor system supported on the HSFD, and compared with that of the conventional squeeze film damper (SFD). Investigation shows that the HSFD not only can significantly improve the high nonlinearity of the SFD, but also can effectively control the rotor vibrational amplitudes, especially for larger rotor unbalance levels and radial clearance ratios, as compared with the SFD.

Study of Transient Characteristic of a Simple Rigid Rotor Supported on a Squeeze Film Damper With Valvular Metal Rubber Squeeze Film Ring

2007 ◽  
Author(s):  
Yanhong Ma ◽  
Jie Hong ◽  
Dayi Zhang ◽  
Hong Wang
Keyword(s):  
High Speed ◽  
Squeeze Film ◽  
Impact Loads ◽  
Rigid Rotor ◽  
Squeeze Film Damper ◽  
Damping Coefficients ◽  
Metal Rubber ◽  
Stiffness And Damping ◽  
Film Stiffness ◽  
Blade Loss

An efficient oil film damper known as a squeeze film damper with valvular metal rubber squeeze film ring (SFD/VMR) was developed for more effective and reliable vibration control, and especially for improving the blade loss dynamics of high-speed rotors based on the conventional squeeze film damper (SFD). The immobile squeeze film ring of the SFD was replaced by the elastic squeeze film ring with the valvular metal rubber subassembly (VMR) of the SFD/VMR. The squeeze film force properties of the SFD/VMR was improved, because it can passively adjust the squeeze film clearance by taking advantage of the elastic deformation of the VMR and can control the squeeze film clearance in a suitable range. The characteristics of squeeze film stiffness and damping coefficients, as well as the steady-state unbalance response of a simple rigid rotor supported on SFD/VMR and SFD, were reported in a previous literature[1]. In this paper, the transient response of the rigid rotor supported on SFD/VMR and SFD subjected to sudden unbalance of blade loss are inverstigated. Time transient simulation and experimental results indicated that SFD/VMR can operate effectively under much greater unbalance compared with SFD, especially under relative large impact loads of blade loss. The SFD/VMR can suppress the occurrence of the nonlinear vibration phenomenon markedly, such as the bistable jump up phenomenon. Furthermore, the effective eccentricities of SFD/VMR with small transfer ratio (T<1.2) extend to two times of SFD, and optimum film stiffness and damping distribution within the whole film clearance can be achieved.

Development of Porous Squeeze Film Damper Bearings for Improving the Blade Loss Dynamics of Rotor-Support Systems

1992 ◽  
Vol 114 (3) ◽  
pp. 347-353 ◽  
Author(s):  
Shiping Zhang ◽  
Litang Yan ◽  
Qihan Li
Keyword(s):  
Squeeze Film ◽  
Rigid Rotor ◽  
Rotor Vibration ◽  
Squeeze Film Damper ◽  
Outer Race ◽  
Squeeze Film Damping ◽  
Rotor Support ◽  
Stiffness And Damping ◽  
Film Stiffness ◽  
Blade Loss

An efficient oil film damper known as porous squeeze film damper (PSFD) is developed based on conventional squeeze film damper (SFD) for more effective and reliable rotor vibration control and especially for improving the blade loss dynamics for rotor support system. The permeability of the outer race of PSFD could remarkably improve the squeeze film damping properties. The transient response of a simple rigid rotor and flexible Jeffcott’s rotor supported on PSFD and SFD subjected to sudden unbalance of blade loss are investigated. Time transient simulation show that PSFD could operate effectively under much greater unbalance as compared with SFD, especially under relative large impact loading of blade loss. Furthermore, the effective eccentricities of PSFD with small transmissibilities (T<1.0) extend to a range of ε<0.9, and optimum film stiffness and damping distribution within the whole film clearance could be achieved.

Squeeze Film Dampers: Amplitude Effects at Low Squeeze Numbers

1975 ◽  
Vol 97 (4) ◽  
pp. 1366-1370 ◽  
Author(s):  
Martin H. Sadd ◽  
A. Kent Stiffler
Keyword(s):  
Reynolds Equation ◽  
Dynamic Performance ◽  
Squeeze Film ◽  
Periodic Disturbance ◽  
Squeeze Film Dampers ◽  
Parallel Surfaces ◽  
Load Characteristics ◽  
Squeeze Number ◽  
Stiffness And Damping ◽  
Film Stiffness

Gaseous squeeze film dampers are analyzed to determine the effect of periodic disturbance amplitude on the dynamic performance. Both circular and rectangular parallel surfaces are investigated. A solution of the nonlinear Reynolds equation is obtained by expanding the pressure in powers of the squeeze number σ, retaining up to and including terms 0(σ2). The time dependent load characteristics are found. The effect of disturbance amplitude on the film stiffness and damping is given.

Electric-Hydraulic Actuator Design for a Hybrid Squeeze-Film Damper-Mounted Rigid Rotor System With Active Control

2005 ◽  
Vol 128 (2) ◽  
pp. 176-183 ◽  
Author(s):  
Her-Terng Yau ◽  
Chieh-Li Chen
Keyword(s):  
Dynamical Behavior ◽  
Rotor System ◽  
Squeeze Film ◽  
Rigid Rotor ◽  
Loop Gain ◽  
Hydraulic Actuator ◽  
Squeeze Film Damper ◽  
Chaotic Vibration ◽  
Squeeze Film Dampers ◽  
Actuator Design

When a squeeze-film damper-mounted rigid rotor system is operated eccentrically, the nonlinear forces are no longer radially symmetric and a disordered dynamical behavior (i.e., quasi-periodic and chaotic vibration) will occur. To suppress the undesired vibration characteristics, the hybrid squeeze-film damper bearing consisting of hydrostatic chambers and hydrodynamic ranges is proposed. In order to change the pressure in hydrostatic chambers, two pairs of electric-hydraulic orifices are used in this paper. The dynamic model of the system is established with the consideration of the electric-hydraulic actuator. The complex nonsynchronous vibration of squeeze-film dampers rotor-bearing system is demonstrated to be stabilized by such electric-hydraulic orifices actuators with proportional-plus-derivative (PD) controllers. Numerical results show that the nonchaotic operation range of the system will be increased by tuning the control loop gain.

Study of a Novel Squeeze Film Damper and Vibration Generator

1999 ◽  
Vol 122 (1) ◽  
pp. 211-218 ◽  
Author(s):  
C. V. Suciu ◽  
O. Bonneau ◽  
D. Brun-Picard ◽  
J. Fre^ne ◽  
M. D. Pascovici
Keyword(s):  
Reynolds Equation ◽  
Industrial Process ◽  
Vibration Damping ◽  
Squeeze Film ◽  
Squeeze Film Damper ◽  
Squeeze Film Effect ◽  
Stiffness And Damping ◽  
Film Stiffness ◽  
Wedge Effect ◽  
Theoretical Results

A novel squeeze film damper and vibration generator (SFD&VG) is proposed as an option in the vibration control field. The SFD&VG can be used as an active squeeze film damper (ASFD) or as a vibration generator (vibrator), for unidimensional vibration damping or generation. The SFD&VG concept is connected with current research to improve a common industrial process—drilling of deep holes. The SFD&VG is based on the variable area of the lubricant film, which allows the development of a variable force, and a change in fluid film stiffness and damping. The analysis is initiated for an elementary configuration of the SFD&VG—the infinite width Rayleigh step case—and then it is developed for an advanced elliptical SFD&VG. The Reynolds equation is solved for both pure squeeze film effect which provides vibration damping, and pure hydrodynamic wedge effect which provides vibration generation. The theoretical part is continued with the SFD&VG dynamic simulation. The SFD&VG experimental device and vibration measurements, performed for the two defined regimes, ASFD and vibration generator, are presented. Finally, the experimental and theoretical results are briefly compared. [S0742-4787(00)05201-2]

Development of an Efficient Oil Film Damper for Improving the Control of Rotor Vibration

1991 ◽  
Vol 113 (4) ◽  
pp. 557-562 ◽  
Author(s):  
Shiping Zhang ◽  
Litang Yan
Keyword(s):  
High Speed ◽  
Porous Metal ◽  
Porous Matrix ◽  
Squeeze Film ◽  
Oil Film ◽  
Squeeze Film Damper ◽  
Outer Race ◽  
Typical Experiment ◽  
Stiffness And Damping ◽  
Film Stiffness

An efficient oil film damper known as a porous squeeze film damper (PSFD) was developed for more effective and reliable vibration control of high-speed rotors based on the conventional squeeze film damper (SFD). The outer race of the PSFD is made of permeable sintered porous metal materials. The permeability allows some of the oil to permeate into and seep out of the porous matrix, with remarkable improvement of the squeeze film damping properties. The characteristics of PSFD oil film stiffness and damping coefficients and permeability, and also, the steady-state unbalance response of a simple rigid rotor and flexible Jeffcott’s rotor supported on PSFD and SFD are investigated. A typical experiment is presented. Investigations show that the nonlinear vibration characteristics of the unpressurized SFD system such as bistable jump phenomena and “lockup” at rotor pin-pin critical speeds could be avoided and virtually disappear under much greater unbalance levels with properly designed PSFD system. PSFD has the potential advantage of operating effectively under relatively large unbalance conditions.

Subharmonic and Quasi-Periodic Motions of an Eccentric Squeeze Film Damper-Mounted Rigid Rotor

1994 ◽  
Vol 116 (3) ◽  
pp. 357-363 ◽  
Author(s):  
J. Y. Zhao ◽  
I. W. Linnett ◽  
L. J. McLean
Keyword(s):  
Numerical Integration ◽  
Least Square ◽  
Harmonic Series ◽  
Squeeze Film ◽  
Maximum Speed ◽  
Rigid Rotor ◽  
Squeeze Film Damper ◽  
Squeeze Film Dampers ◽  
The Stability ◽  
Nonsynchronous Vibrations

When a squeeze-film damper is operated eccentrically, the nonlinear damper forces are no longer radially symmetric and subharmonic and quasi-periodic vibrations may be excited by the rotor unbalance. In this study, the unbalance response of a rigid rotor, supported on an eccentric squeeze film damper, is first approximated by a harmonic series whose coefficients are determined by the collocation method, together with a nonlinear least-square regression. The stability of the resulting periodic solution is then examined using the Floquet transition matrix method. For sufficiently large values of the unbalance and the damper static radial misalignment, it is shown that the approximate harmonic motion loses its stability and bifurcates into a stable subharmonic motion and a quasi-periodic motion at speeds above twice the system critical speed. This analytical finding is verified by a numerical integration in forms of the Poincare´ map, the rotor trajectory, the bifurcation diagram, and the power spectrum. It is suggested that stability analysis and numerical integration should always be incorporated into an approximate analytical method to achieve an adequate approximation. The results of this study show that the introduction of squeeze-film dampers may give rise to the undesirable nonsynchronous vibrations, which limits the maximum speed at which dampers should be used.

scholarly journals An Improved Squeeze Film Damper for Rotor Vibration Control: Theoretical Results

1994 ◽  
Author(s):  
J. Y. Zhao ◽  
I. W. Linnett ◽  
E. J. Hahn
Keyword(s):  
Operating Conditions ◽  
Outer Ring ◽  
Squeeze Film ◽  
Squeeze Film Damper ◽  
Constant Stiffness ◽  
Wide Range ◽  
Squeeze Film Dampers ◽  
Secondary Support ◽  
Stiffness And Damping ◽  
Theoretical Results

This paper proposes an improved squeeze film damper which will prevent the bistable operation associated with conventional squeeze film dampers at large unbalances and/or at small bearing parameters. It consists of a conventional squeeze film damper with a flexibly supported outer ring. This secondary flexible support is considered to be massless, and to have a constant stiffness and damping. The effectiveness of this damper in preventing bistable operation is investigated over a wide range of operating conditions for a rigid rotor supported on a centrally preloaded squeeze film damper. It is shown that depending on relevant parameters such as the stiffness ratio between the secondary support and the retaining spring, the damping coefficient of the support, and the mass ratio between the damper outer ring and the rotor, this proposed damper is very effective in preventing bistable operation even for high unbalance conditions.

Sign in / Sign up

Export Citation Format

Share Document