Finite Element Modeling of Annular-Like Acoustic Cavities

1985 ◽  
Vol 107 (1) ◽  
pp. 81-85
Author(s):  
Chaw-Hua Kung ◽  
Rajendra Singh
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Pressure Oscillation ◽  
Transient Heat Conduction ◽  
Natural Frequencies And Modes ◽  
Acoustic Cavities ◽  
Eigen Solutions ◽  
Element Technique ◽  
Good Agreement

A finite element technique has been developed to find natural frequencies and modes of undamped three-dimensional acoustic cavities. This method utilizes the analogy between a special form of the discretized transient heat conduction equations and discretized equations of acoustic pressure oscillation. The proposed technique is verified by applying it to several cavities of known theoretical eigen-solutions. Computed results for an acoustic ring, an acoustic disk, and a pure annular cavity match extremely well with exact solutions. In addition, the condensation scheme is investigated and guidelines of selecting acoustic master nodes appropriately are also discussed in the paper. Using the validated finite element method along with suitable condensation, the eigenvalue problem of an annular-like cavity is solved. Since the exact solution for this case is not possible, finite element computations for natural frequencies and modes are compared with the measured results obtained using an acoustic modal analysis experimental technique; again very good agreement has been found.

Modeling Procedures for the Stress Analysis of Flexible Pipe Cross Sections

1993 ◽  
Vol 115 (1) ◽  
pp. 46-51 ◽  
Author(s):  
A. M. Harte ◽  
J. F. McNamara
Keyword(s):  
Finite Element ◽  
Analytical Model ◽  
Cross Sections ◽  
Three Dimensional ◽  
Flexible Pipe ◽  
Discrete Reinforcement ◽  
Tube Type ◽  
Element Technique ◽  
Main Deformation ◽  
Good Agreement

Thick tube theory is incorporated into an existing analytical model for the three-dimensional analysis of bonded flexible pipe cross sections under offshore loading conditions. The original model considers material layers as isotropic/orthotopic thin tubes, and layers of helically wound reinforcing cables are modeled separately. The improvement in the results obtained with the incorporation of the new thick tube layer is demonstrated for a flexible pipe with D/t = 10. The finite element technique has also been used to model this type of pipe structure. Pipe sections are discretized using axisymmetric elements for the tube-type layers and special discrete reinforcement elements for the helical cables. A particular example of a three-layer doubly reinforced pipe section under internal pressure is studied. Good agreement is found between analytical model and finite element results for all the main deformation and stress quantities including cable stresses.

scholarly journals Out-of-Plane Vibration of Curved Uniform and Tapered Beams with Additional Mass

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Hamdi Alper Özyiğit ◽  
Mehmet Yetmez ◽  
Utku Uzun
Keyword(s):  
Finite Element ◽  
Free Vibration ◽  
Boundary Conditions ◽  
Natural Frequencies ◽  
Variable Cross ◽  
Additional Mass ◽  
Inertia Effects ◽  
Tapered Beam ◽  
Out Of Plane ◽  
Good Agreement

As there is a gap in literature about out-of-plane vibrations of curved and variable cross-sectioned beams, the aim of this study is to analyze the free out-of-plane vibrations of curved beams which are symmetrically and nonsymmetrically tapered. Out-of-plane free vibration of curved uniform and tapered beams with additional mass is also investigated. Finite element method is used for all analyses. Curvature type is assumed to be circular. For the different boundary conditions, natural frequencies of both symmetrical and unsymmetrical tapered beams are given together with that of uniform tapered beam. Bending, torsional, and rotary inertia effects are considered with respect to no-shear effect. Variations of natural frequencies with additional mass and the mass location are examined. Results are given in tabular form. It is concluded that (i) for the uniform tapered beam there is a good agreement between the results of this study and that of literature and (ii) for the symmetrical curved tapered beam there is also a good agreement between the results of this study and that of a finite element model by using MSC.Marc. Results of out-of-plane free vibration of symmetrically tapered beams for specified boundary conditions are addressed.

Effective Shear Area in One Dimensional Ship Hull Finite Element Models to Predict Natural Frequencies of Vibration

2013 ◽  
Author(s):  
Osvaldo Pinheiro de Souza e Silva ◽  
Severino Fonseca da Silva Neto ◽  
Ilson Paranhos Pasqualino ◽  
Antonio Carlos Ramos Troyman
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Experimental Tests ◽  
Numerical Results ◽  
Computational Method ◽  
Scale Model ◽  
Dimensional Model ◽  
One Dimensional ◽  
Shear Area

This work discusses procedures used to determine effective shear area of ship sections. Five types of ships have been studied. Initially, the vertical natural frequencies of an acrylic scale model 3m in length in a laboratory at university are obtained from experimental tests and from a three dimensional numerical model, and are compared to those calculated from a one dimensional model which the effective shear area was calculated by a practical computational method based on thin-walled section Shear Flow Theory. The second studied ship was a ship employed in midshipmen training. Two models were made to complement some studies and vibration measurements made for those ships in the end of 1980 decade when some vibration problems in them were solved as a result of that effort. Comparisons were made between natural frequencies obtained experimentally, numerically from a three dimensional finite element model and from a one dimensional model in which effective shear area is considered. The third and fourth were, respectively, a tanker ship and an AHTS (Anchor Handling Tug Supply) boat, both with comparison between three and one dimensional models results out of water. Experimental tests had been performed in these two ships and their results were used in other comparison made after the inclusion of another important effect that acts simultaneously: the added mass. Finally, natural frequencies experimental and numerical results of a barge are presented. The natural frequencies numerical results of vertical hull vibration obtained from these approximations of effective shear areas for the five ships are finally discussed.

Finite Element Analysis of Elliptical Chord

2013 ◽  
Vol 3 (4) ◽  
pp. 44-61
Author(s):  
K. S. Narayana ◽  
R. T. Naik ◽  
R. C. Mouli ◽  
L. V. V. Gopala Rao ◽  
R. T. Babu Naik
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Compressive Load ◽  
Dynamic Strength ◽  
Element Analysis ◽  
T Joints ◽  
Shell Elements ◽  
Tubular Joints ◽  
Plane Bending

The work presents the Finite element study of the effect of elliptical chords on the static and dynamic strength of tubular T-joints using ANSYS. Two different geometry configurations of the T-joints have been used, namely Type-1 and Type-2. An elastic analysis has been considered. The Static loading conditions used are: axial load, compressive load, In-plane bending (IPB) and Out-plane bending (OPB). The natural frequencies analysis (dynamic loading condition) has also been carried out. The geometry configurations of the T-joints have been used, vertical tubes are called brace and horizontal tubes are called chords. The joint consists of brace joined perpendicular to the circular chord. In this case the ends of the chord are held fixed. The material used is mild steel. Using ANSYS, finite element modeling and analysis of T-joint has been done under the aforementioned loading cases. It is one of the most powerful methods in use but in many cases it is an expensive analysis especially due to elastic–plastic and creep problems. Usually, three dimensional solid elements or shell elements or the combination of two types of elements are used for generating the tubular joints mesh. In tubular joints, usually the fluid induced vibrations cause the joint to fail under resonance. Therefore the natural frequencies analysis is also an important issue here. Generally the empirical results are required as guide or comparison tool for finite element investigation. It is an effective way to obtain confidence in the results derived. Shell elements have been used to model the assembled geometry. Finite element ANSYS results have been validated with the LUSAS FEA and experimental results, that is within the experimentation error limit of ten percentage.

scholarly journals A Novel Highly Accurate Finite-Element Family

2017 ◽  
Vol 2017 ◽  
pp. 1-20
Author(s):  
Giovanni Bernardini ◽  
Fabio Cetta ◽  
Luigi Morino
Keyword(s):  
Finite Element ◽  
Structural Dynamics ◽  
Hermite Interpolation ◽  
Natural Frequencies ◽  
Finite Thickness ◽  
Three Dimensional ◽  
Numerical Results ◽  
Small Thickness ◽  
Modes Of Vibration ◽  
Patch Technique

A novel Nth order finite element for interior acoustics and structural dynamics is presented, with N arbitrarily large. The element is based upon a three-dimensional extension of the Coons patch technique, which combines high-order Lagrange and Hermite interpolation schemes. Numerical applications are presented, which include the evaluation of the natural frequencies and modes of vibration of (1) air inside a cavity (interior acoustics) and (2) finite-thickness beams and plates (structural dynamics). The numerical results presented are assessed through a comparison with analytical and numerical results. They show that the proposed methodology is highly accurate. The main advantages however are (1) its flexibility in obtaining different level of accuracy (p-convergence) simply by increasing the number of nodes, as one would do for h-convergence, (2) the applicability to arbitrarily complex configurations, and (3) the ability to treat beam- and shell-like structures as three-dimensional small-thickness elements.

Prediction of Blade Flutter in a Tuned Rotor

1985 ◽  
Author(s):  
Jianmin Xu ◽  
Zhaohong Song
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Degrees Of Freedom ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Rotating Blades ◽  
Multiple Degrees Of Freedom ◽  
Strip Theory ◽  
Blade Flutter ◽  
Good Agreement

This paper is about blade flutter in a tuned rotor. With the aid of the combination of three dimensional structural finite element method, two dimensional aerodynamical finite difference method and strip theory, the quasi-steady models in which two degrees of freedom for a single wing were considered have been extended to multiple degrees of freedom for the whole blade in a tuned rotor. The eigenvalues solved from the blade motion equation have been used to judge whether the system is stable or not. The calculating procedure has been formed and using it the first stage rotating blades of a compressor where flutter had occurred, have been predicted. The numerical flutter boundaries have good agreement with the experimental ones.

Residual Stress Prediction for Non-Axisymmetric Vessel Penetration Welds

2008 ◽  
Author(s):  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Three Dimensional ◽  
Measurement Data ◽  
Fe Model ◽  
Stress Distributions ◽  
Dimensional Finite Element ◽  
Stress Prediction ◽  
Three Dimensional Finite Element ◽  
Good Agreement

Residual stress distribution in an oblique nozzle jointed to a vessel with J-groove welds was analyzed using a three-dimensional finite element method. All welding passes were considered in a 180-degree finite element (FE) model with symmetry. Temperature and stress were modeled for simultaneous bead laying. To determine residual stress distributions at the welds experimentally, a mock-up specimen was manufactured. The analytical results show good agreement with the experimental measurement data, indicating that FE modeling is valid.

Dynamical Behaviour of a Materially Damped Flexible Towed Cable

1972 ◽  
Vol 23 (2) ◽  
pp. 109-120 ◽  
Author(s):  
T C Cannon ◽  
J Genin
Keyword(s):  
Closed Form ◽  
Natural Frequencies ◽  
Equilibrium Shape ◽  
Equations Of Motion ◽  
Three Dimensional ◽  
Dynamical Behaviour ◽  
Aerodynamic Loading ◽  
Towed Cable ◽  
Closed Form Approximation ◽  
Good Agreement

SummaryThe three-dimensional equations of motion of a flexible towed cable are developed. A closed-form approximation for the equilibrium shape of a cable subjected to arbitrary aerodynamic loading is developed and used in the study of a heavy, vibrating tow cable. Natural frequencies of vibration and cable shapes are computed for typical cables and are shown to be in good agreement with exact, numerically obtained values.

Sign in / Sign up

Export Citation Format

Share Document