Augmentation of Laminar Flow Heat Transfer in Tubes by Means of Twisted-Tape Inserts

1976 ◽  
Vol 98 (2) ◽  
pp. 251-256 ◽  
Author(s):  
S. W. Hong ◽  
A. E. Bergles
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Reynolds Numbers ◽  
Twisted Tape ◽  
Transfer Coefficients ◽  
Constant Property ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Flow Heat ◽  
High Reynolds

Heat transfer coefficients for laminar flow of water and ethylene glycol in an electrically heated metal tube with two twisted-tape inserts were determined experimentally. The Nusselt number for fully developed flow was found to be a function of tape twist ratio, Reynolds number, and Prandtl number. These Nusselt numbers were as much as nine times the empty tube constant property values. The correlation of these data is in fair agreement with the only available analytical predictions. The friction factor is affected by tape twist only at high Reynolds numbers, in accordance with analytical predictions. The performance of these augmented tubes is compared with that of empty tubes under similar heating conditions.

Heat Transfer in a Surfactant Drag-Reducing Solution—A Comparison With Predictions for Laminar Flow

2005 ◽  
Vol 128 (6) ◽  
pp. 557-563 ◽  
Author(s):  
Paul L. Sears ◽  
Libing Yang
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Reynolds Numbers ◽  
High Heat ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Drag Reducing Additive ◽  
Good Agreement

Heat transfer coefficients were measured for a solution of surfactant drag-reducing additive in the entrance region of a uniformly heated horizontal cylindrical pipe with Reynolds numbers from 25,000 to 140,000 and temperatures from 30to70°C. In the absence of circumferential buoyancy effects, the measured Nusselt numbers were found to be in good agreement with theoretical results for laminar flow. Buoyancy effects, manifested as substantially higher Nusselt numbers, were seen in experiments carried out at high heat flux.

Heat Transfer and Pressure Drop Correlations for Square Channels With 45 Deg Ribs at High Reynolds Numbers

2009 ◽  
Vol 131 (7) ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Huitao Yang ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Turbine Blade Cooling ◽  
Square Channel ◽  
Heat Transfer Coefficients ◽  
High Reynolds ◽  
Cooling Passage

Systematic experiments are conducted to measure heat transfer enhancement and pressure loss characteristics on a square channel (simulating a gas turbine blade cooling passage) with two opposite surfaces roughened by 45 deg parallel ribs. Copper plates fitted with a silicone heater and instrumented with thermocouples are used to measure regionally averaged local heat transfer coefficients. Reynolds numbers studied in the channel range from 30,000 to 400,000. The rib height (e) to hydraulic diameter (D) ratio ranges from 0.1 to 0.18. The rib spacing (p) to height ratio (p/e) ranges from 5 to 10. Results show higher heat transfer coefficients at smaller values of p/e and larger values of e/D, though at the cost of higher friction losses. Results also indicate that the thermal performance of the ribbed channel falls with increasing Reynolds numbers. Correlations predicting Nusselt number (Nu) and friction factor (f¯) as a function of p/e, e/D, and Re are developed. Also developed are correlations for R and G (friction and heat transfer roughness functions, respectively) as a function of the roughness Reynolds number (e+), p/e, and e/D.

Heat Transfer from a Plate Elevated above a Host Surface and Washed by a Separated Flow Induced by the Elevation Step

1981 ◽  
Vol 103 (3) ◽  
pp. 441-447 ◽  
Author(s):  
E. M. Sparrow ◽  
F. Samie ◽  
S. C. Lau
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Angle Of Attack ◽  
Separated Flow ◽  
Active Surface ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Reynolds Number Flow ◽  
Heat Transfer Coefficients ◽  
High Reynolds

Wind tunnel experiments were performed to determine heat transfer coefficients and fluid flow patterns for a thermally active surface elevated above a parallel host surface. The step-like blockage associated with the elevation causes flow separation and recirculation on the forward portion of the thermally active surface. Four parameters were varied during the course of the experiments, including the angle of attack of the oncoming airflow relative to the surface, the step height, the extent of the host surface which frames the active surface (i.e., the skirt width), and the Reynolds number. Flow visualization studies, performed with the oil-lampblack technique, showed that the streamwise extent of the separation zone increases with decreasing angle of attack, with larger step heights and skirt widths, and at higher Reynolds numbers. At larger angles of attack, separation does not occur. The experimentally determined heat transfer coefficients were found to increase markedly due to the flow separation, and separation-related enhancements as large as a factor of two were encountered. The enhancement was accentuated at small angles of attack, at large step heights and skirt widths, and at high Reynolds numbers. A main finding of the study is that the separation-affected heat transfer coefficients are generally greater than those for no separation, so that the use of the latter may underestimate the heat transfer rates. For an application such as a retrofit solar collector, such an underestimation of the wind-related heat loss would yield an optimistic prediction of the collector efficiency.

Single-Phase Heat Transfer in Mems-Based Pin Fin Heat Sink

2005 ◽  
Author(s):  
Ali Kosar ◽  
Yoav Peles
Keyword(s):  
Heat Transfer ◽  
Single Phase ◽  
Reynolds Numbers ◽  
Heat Fluxes ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Pin Fins ◽  
Micro Pin Fins

An experimental study has been performed on single-phase heat transfer of de-ionized water over a bank of shrouded micro pin fins 243-μm long with hydraulic diameter of 99.5-μm. Heat transfer coefficients and Nusselt numbers have been obtained over effective heat fluxes ranging from 3.8 to 167 W/cm2 and Reynolds numbers from 14 to 112. The results were used to derive the Nusselt numbers and total thermal resistances. It has been found that endwalls effects are significant at low Reynolds numbers and diminish at higher Reynolds numbers.

Measurement and Analysis of Laminar Heat Transfer Coefficients in Micro and Mini-Scale Ducts and Channels

2014 ◽  
Author(s):  
Y. S. Muzychka ◽  
M. Ghobadi
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Constant Wall Temperature ◽  
Fully Developed Flow ◽  
Transfer Rates ◽  
Heat Transfer Coefficients ◽  
Advantages And Disadvantages ◽  
Nusselt Numbers

Heat transfer in micro and mini-scale ducts and channels is considered. In particular, issues of thermal performance are considered in systems with constant wall temperature at low to moderate Reynolds numbers or small dimensional scales which lead to conditions characteristic of thermally fully developed flows or within the transition region leading to thermally fully developed flows. An analysis of two approaches to representing experimental data is given. One using the traditional Nusselt number and another using the dimensionless mean wall flux. Both approaches offer a number of advantages and disadvantages. In particular, it is shown that while good data can be obtained which agree with predicted heat transfer rates, the same data can be problematic if one desires a Nusselt number. Other issues such as boundary conditions pertaining to measuring thermally developing and fully developed flow Nusselt numbers are also discussed in detail.

Streamwise Flow and Heat Transfer Distributions for Jet Array Impingement With Crossflow

1981 ◽  
Author(s):  
L. W. Florschuetz ◽  
C. R. Truman ◽  
D. E. Metzger
Keyword(s):  
Heat Transfer ◽  
Flow Distribution ◽  
Reynolds Numbers ◽  
Geometric Parameters ◽  
Channel Height ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Circular Jets

Two-dimensional arrays of circular jets of air impinging on a heat transfer surface parallel to the jet orifice plate are considered. The air, after inpingement, is constrained to exit in a single direction along the channel formed by the surface and the jet plate. The downstream jets are subjected to a crossflow originating from the upstream jets. Experimental and theoretical results obtained for streamwise distributions of jet and crossflow velocities are presented and compared. Measured Nusselt numbers resolved to one streamwise hole spacing are correlated with individual spanwise row jet Reynolds numbers and crossflow-to-jet velocity ratios. Correlations are presented for both inline and staggered hole patterns including effects of geometric parameters: streamwise hole spacing, spanwise hole spacing, and channel height, normalized by hole diameter. The physical mechanisms influencing heat transfer coefficients as a function of flow distribution and geometric parameters are also discussed.

scholarly journals Heat Transfer Coefficients for Staggered Arrays of Short Pin Fins

1981 ◽  
Author(s):  
G. J. VanFossen
Keyword(s):  
Heat Transfer ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Total Heat Transfer ◽  
Optimum Length ◽  
Trailing Edge ◽  
Heat Transfer Coefficients ◽  
Casting Technology ◽  
Nusselt Numbers ◽  
Pin Fins

Short pin fins are often used to increase the heat transfer to the coolant in the trailing edge of a turbine blade. Due primarily to limits of casting technology, it is not possible to manufacture pins of optimum length for heat transfer purposes in the trailing edge region. In many cases the pins are so short that they actually decrease the total heat transfer surface area compared to a plain wall. A heat transfer data base for these short pins is not available in the literature. Heat transfer coefficients on pin and endwall surfaces were measured for several staggered arrays of short pin fins. The measured Nusselt numbers when plotted versus Reynolds numbers were found to fall on a single curve for all surfaces tested. The heat transfer coefficients for the short pin fins (length to diameter ratios of 1/2 and 2) were found to be about a factor of two lower than data from the literature for longer pin arrays (length to diameter ratios of about 8).

Turbulent Convective Heat Transfer in Forced Cooled Underground Electric Transmission Systems

1985 ◽  
Vol 107 (2) ◽  
pp. 327-333 ◽  
Author(s):  
R. Ghetzler ◽  
J. C. Chato ◽  
J. M. Crowley
Keyword(s):  
Heat Transfer ◽  
Reynolds Numbers ◽  
Scale Model ◽  
Transfer Coefficients ◽  
Transmission Systems ◽  
Number Range ◽  
Heat Transfer Coefficients ◽  
Electric Transmission ◽  
Friction Factors ◽  
High Reynolds

Heat transfer and friction factors were experimentally determined in a scale model of high-voltage, pipe-type underground transmission systems for Reynolds numbers to 8000. Dielectric insulating oil (Sun No. 4) with a Prandtl number of 120 was utilized for the coolant. Two ratios of cable to enclosure pipe diameters, corresponding to standard and oversize enclosure pipes, were examined for the three-cable system. Helical wire wrap was included to simulate protective skid wires around the cables. Three configurations of cable positioning were considered—open triangular, close triangular, and cradled. A method of generalizing the heat transfer coefficients was developed and tested for rough pipe cables based on extensions of previous work in the literature. The generalized correlation, without correction factors, was found to be applicable only in two cases with appropriate flow pattens and geometries. Heat transfer to the pipe wall could be correlated by standard methods in the high Reynolds number range.

An Experimental and Numerical Investigation on the Thermal-Hydraulic Performance of Double Notched Plate

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
Lei Zhang ◽  
Defu Che
Keyword(s):  
Heat Transfer ◽  
Swirling Flow ◽  
Reynolds Numbers ◽  
Velocity Fields ◽  
Local Information ◽  
Transfer Coefficients ◽  
Enhanced Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Friction Factors

The double notched (DN) plate is commonly used in rotary air preheaters, but relevant investigations are rare. Thus, thermal-hydraulic performances of the DN plate are investigated in this paper. A single-blow, transient technique is refined and then used to measure the overall mean heat transfer coefficients and friction factors. A validated numerical method is also utilized to provide local information. The measured results show that the performance of the DN plate approaches that of the double undulated (DU) plate and lies between that of the cross corrugated (CC) plate and the parallel plate. No swirling flow pattern is identified in the predicted velocity fields. Basically, two types of flow are observed: wavy channel flow and pipe flow. High or low Nusselt numbers, Nu, are obtained at the luff or lee side of undulations and notches, respectively. Nu values increase and Nu distributions become more homogenous with increasing Reynolds numbers, Re. A recommendation is made that the DN plate be operated under moderate Re to achieve homogenous and enhanced heat transfer, given the allowable pressure drop.

Heat Transfer and Pressure Drop Measurements for a Square Channel With 45 deg Round-Edged Ribs at High Reynolds Numbers

2010 ◽  
Vol 133 (3) ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Nawaf Alkhamis ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Friction Factor ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Height Ratio ◽  
Square Channel ◽  
Heat Transfer Coefficients ◽  
Friction Factors ◽  
High Reynolds ◽  
The Cost

Experiments to determine heat transfer coefficients and friction factors are conducted on a stationary 45 deg parallel rib-roughened square channel, which simulates a turbine blade internal coolant passage. Copper plates fitted with silicone heaters and thermocouples are used to measure regionally averaged heat transfer coefficients. Reynolds numbers studied range from 30,000 to 400,000. The ribs studied have rounded (filleted) edges to account for manufacturing limitations of actual engine blades. The rib height (e) to hydraulic diameter (D) ratio (e/D) ranges from 0.1 to 0.2, while spacing (p) to height ratio (p/e) ranges from 5 to 10. Results indicate an increase in the heat transfer due to the ribs at the cost of a higher friction factor, especially at higher Reynolds numbers. Round-edged ribs experience a similar heat transfer coefficient and a lower friction factor compared with sharp-edged ribs, especially at higher values of the rib height. Correlations predicting Nu and f as a function of e/D, p/e, and Re are presented. Also presented are correlations for the heat transfer and friction roughness parameters (G and R, respectively).

Sign in / Sign up

Export Citation Format

Share Document