Estimation of Dynamic Forces in Very High-Speed Impact Forging

1966 ◽  
Vol 88 (4) ◽  
pp. 369-372 ◽  
Author(s):  
M. J. Hillier
Keyword(s):  
Approximate Solution ◽  
Velocity Field ◽  
Plane Strain ◽  
Energy Method ◽  
Coulomb Friction ◽  
High Speed ◽  
Admissible Velocity ◽  
High Speed Impact ◽  
Dynamic Forces ◽  
Very High

A study is made of three methods of estimating die loads in impact forging: By approximate solution of the equations of equilibrium; by an energy method, assuming plane sections remain plane; and using the energy method in association with a kinematically admissible velocity field. Results are given for die pressures and die loads for axisymmetric and plane-strain forging of disks and slabs with smooth dies, perfectly rough dies, and for the case of Coulomb friction.

Analysis of very high speed impact

1987 ◽  
Vol 25 (4) ◽  
pp. 473-482 ◽  
Author(s):  
M. Ravid ◽  
S.R. Bodner ◽  
I. Holcman
Keyword(s):  
High Speed ◽  
High Speed Impact ◽  
Very High

A Generalized Velocity Field for Plane Strain Extrusion Through Arbitrarily Curved Dies

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
H. Haghighat ◽  
P. Amjadian
Keyword(s):  
Finite Element ◽  
Velocity Field ◽  
Angular Velocity ◽  
Plane Strain ◽  
Upper Bound ◽  
Velocity Fields ◽  
Finite Element Code ◽  
Admissible Velocity ◽  
Paper Plane ◽  
Good Agreement

In this paper, plane strain extrusion through arbitrarily curved dies is investigated analytically, numerically, and experimentally. Two kinematically admissible velocity fields based on assuming proportional angles, angular velocity field, and proportional distances from the midline in the deformation zone, sine velocity field, are developed for use in upper bound models. The relative average extrusion pressures for the two velocity fields are compared to each other and also with the velocity field of a reference for extrusion through a curved die. The results demonstrate that the angular velocity field is the best. Then, by using the developed analytical model, optimum die lengths which minimize the extrusion loads are determined for a streamlined die and also for a wedge shaped die. The corresponding results for those two die shapes are also determined by using the finite element code and by doing some experiments and are compared with upper bound results. These comparisons show a good agreement.

Structural changes in silicon-on-insulator material during post-implantation annealing

1986 ◽  
Vol 44 ◽  
pp. 736-737
Author(s):  
C. O. Jung ◽  
S. J. Krause ◽  
S.R. Wilson
Keyword(s):  
Integrated Circuits ◽  
Oxide Layer ◽  
High Speed ◽  
Structural Changes ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Quality ◽  
Radiation Hardened ◽  
Post Implantation ◽  
Very High

Silicon-on-insulator (SOI) structures have excellent potential for future use in radiation hardened and high speed integrated circuits. For device fabrication in SOI material a high quality superficial Si layer above a buried oxide layer is required. Recently, Celler et al. reported that post-implantation annealing of oxygen implanted SOI at very high temperatures would eliminate virtually all defects and precipiates in the superficial Si layer. In this work we are reporting on the effect of three different post implantation annealing cycles on the structure of oxygen implanted SOI samples which were implanted under the same conditions.

YSS HAP72

Alloy Digest ◽  
2019 ◽  
Vol 68 (10) ◽  
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Powder Metallurgy ◽  
Tool Steel ◽  
High Speed ◽  
High Wear Resistance ◽  
Bend Strength ◽  
Temperature Performance ◽  
Very High

Abstract YSS HAP72 is a powder metallurgy high-speed tool steel with a very high wear resistance. This datasheet provides information on composition, hardness, and bend strength. It also includes information on high temperature performance. Filing Code: TS-779. Producer or source: Hitachi Metals America Ltd.

Sign in / Sign up

Export Citation Format

Share Document