Terahertz Absorber with Graphene Enhanced Polymer Hemispheres Array

We propose an original technique for the fabrication of terahertz (THz) metasurfaces comprising a 3D printed regular array of polymer hemispheres covered with a thin conductive layer. We demonstrate that the deposition of a thin metal layer onto polymer hemispheres suppresses the THz reflectivity to almost zero, while the frequency range of such a suppression can be considerably broadened by enhancing the structure with graphene. Scaling up of the proposed technique makes it possible to tailor the electromagnetic responses of metasurfaces and allows for the fabrication of various components of THz photonics.

Combining Interference Lithography and Two-Photon Lithography for Fabricating Large-Area Photonic Crystal Structures with Controlled Defects

Interference lithography is a promising method for fabricating large-area, defect-free three-dimensional photonic crystal structures which can be used for facilitating the realization of photonic devices with a fast processing time. Although they can be used in waveguides, resonators, and detectors, their repeated regular array patterns can only be used for limited applications. In this study, we demonstrate a method for fabricating large-area photonic crystal structures with controlled defects by combining interference lithography and two-photon lithography using a light-curable resin. By combining regular array structures and controlled patterns, monotonous but large-area regular structures can be obtained. Furthermore, the patterned structures have considerable potential for use in various applications, such as solar cells, sensors, photodetectors, micro-/nano-electronics, and cell growth.

Dynamically induced friction reduction in micro-structured interfaces

We investigate the dynamic behavior of a regular array of in-plane elastic supports interposed between a sliding rigid body and a rigid substrate. Each support is modelled as a mass connected to a fixed pivot by means of radial and tangential elastic elements. Frictional interactions are considered at the interface between the supports and the sliding body. Depending on the specific elastic properties of the supports, different dynamic regimes can be achieved, which, in turn, affect the system frictional behavior. Specifically, due to transverse microscopic vibration of the supports, a lower friction force opposing the macroscopic motion of the rigid body can be achieved compared to the case where no supports are present and rubbing occurs with the substrate. Furthermore, we found that the supports static orientation plays a key role in determining the frictional interactions, thus offering the chance to specifically design the array aiming at controlling the resulting interfacial friction force.

Fluorescence Switchable Conjugated Polymer Microdisk Arrays by Cosolvent Vapor Annealing

Depositing minute light emitters into a regular array is a basic but essential technique in display technology. However, conventional lithographic methodologies involve multistep and energy-consuming processes. Here, we develop a facile method in which organic and polymeric fluorescent dyes spontaneously aggregate to form a patterned microarray. We find that a thin film of fluorescent π-conjugated polymer transforms into micrometer-sized aggregates when exposed to binary organic vapor at ambient temperature. The arrayed microaggregates can be formed over the whole substrate surface when using a quartz substrate that is prepatterned with regular hydrophilic boxes and hydrophobic grids. The resultant microarray is applicable to optical memories and displays when photoswitchable fluorophores are doped into the polymer matrix.

Experimental and Computational Methods for the Evaluation of Double-Wall, Effusion Cooling Systems

Further improvements in gas turbine efficiency can be sought through more advanced cooling systems—such as the double-wall, effusion system—which provide high cooling effectiveness with low coolant utilization. The double-wall system, as described here, comprises two walls: one with a regular array of impingement holes and the other with a closely packed, regular array of film holes (characteristic of effusion systems). These walls are mechanically and thermally connected via a bank of pedestals which increase coolant wetted area and turbulent flow features. However, a lack of data exists in the open literature on these systems. This study presents a novel experimental heat transfer facility designed with the intent of investigating flat plate versions of such double-wall geometries. Key features of the facility are presented including the use of recirculation to increase the mainstream-to-coolant temperature ratio and the use of infrared thermography to obtain thermal measurements. Some rig commissioning characteristics are also provided which demonstrate well-conditioned, uniform flow. Both coolant and mainstream Reynolds numbers are matched to engine conditions, with the Biot number within around 15% of engine conditions. The facility is used to assess the cooling performance of four double-wall effusion geometries which incorporate various geometrical features. Both overall effectiveness and film effectiveness measurements are presented at a range of coolant mass flows with conclusions drawn as to preferable features from a cooling perspective. The results from a fully conjugate computational fluid dynamics (CFD) model of the facility are presented which utilized boundary conditions obtained during experimental runs. Additionally, a computationally efficient decoupled conjugate method developed previously by the authors was adapted to assess the experimental geometries with the results comparing favorably.

FLN-1/Filamin is required to anchor the actomyosin cytoskeleton and for global organization of sub-cellular organelles in a contractile tissue

Actomyosin networks are organized in space, direction, size, and connectivity to produce coordinated contractions across cells. We use the C. elegans spermatheca, a tube composed of contractile myoepithelial cells, to study how actomyosin structures are organized. FLN-1/filamin is required for the formation and stabilization of a regular array of parallel, contractile, actomyosin fibers in this tissue. Loss of fln-1 results in the detachment of actin fibers from the basal surface, which then accumulate along the cell junctions and are stabilized by spectrin. In addition, actin and myosin are captured at the nucleus by the linker of nucleoskeleton and cytoskeleton complex (LINC) complex, where they form large foci. Nuclear positioning and morphology, distribution of the endoplasmic reticulum and the mitochondrial network are also disrupted. These results demonstrate that filamin is required to prevent large actin bundle formation and detachment, to prevent excess nuclear localization of actin and myosin, and to ensure correct positioning of organelles.