Precombustion Chamber Design for Emissions Reduction From Large Bore NG Engines

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
Dean J. Simpson ◽  
Daniel B. Olsen
Keyword(s):  
Natural Gas ◽  
Combustion Stability ◽  
Nozzle Geometry ◽  
Oxides Of Nitrogen ◽  
Lean Burn ◽  
Engine Operation ◽  
Chamber Volume ◽  
Fuel Delivery ◽  
Design Variables ◽  
Partial Load

Precombustion chambers (PCCs) are an ignition technology for large bore, natural gas engines, which can extend the lean operating limit through improved combustion stability. Previous research indicates that the PCC is responsible for a significant portion of engine-out emissions, especially near the lean limit of engine operation. In this work, six concept PCC designs are developed with the objective of reducing engine-out emissions, focusing on oxides of nitrogen (NOx). The design variables include chamber geometry, chamber volume, fuel delivery, nozzle geometry, and material thermal conductivity. The concepts are tested on a single cylinder of a large bore, two-stroke cycle, lean burn, natural gas compressor engine, and the results are compared with stock PCC performance. The pollutants of interest include NOx, carbon monoxide, total hydrocarbons, and volatile organic compounds (VOCs). The results indicate that PCC volume has the largest effect on the overall NOx–CO tradeoff. Multiple nozzles and electronic PCC fuel control were found to enhance main chamber combustion stability, particularly at partial load conditions. The PCC influence on VOCs was insignificant; rather, VOCs were found to be heavily dependent on fuel composition.

Evaluation of Spark Plug and Timing Configurations on the Fuel Consumption, Combustion Stability, and Emissions of a Large-Bore, Two-Stroke, Natural Gas Engine

2016 ◽  
Author(s):  
Derek Johnson ◽  
Marc Besch ◽  
Nathaniel Fowler ◽  
Robert Heltzel ◽  
April Covington
Keyword(s):  
Natural Gas ◽  
Fuel Consumption ◽  
Combustion Engine ◽  
Engine Performance ◽  
Combustion Stability ◽  
Oxides Of Nitrogen ◽  
Natural Gas Engines ◽  
Fuel Delivery ◽  
Spark Plug ◽  
Trade Offs

Emissions compliance is a driving factor for internal combustion engine research pertaining to both new and old technologies. New standards and compliance requirements for off-road spark ignited engines are currently under review and include greenhouse gases. To continue operation of legacy natural gas engines, research is required to increase or maintain engine efficiency, while reducing emissions of carbon monoxide, oxides of nitrogen, and volatile organic compounds such as formaldehyde. A variety of technologies can be found on legacy, large-bore natural gas engines that allow them to meet current emissions standards — these include exhaust after-treatment, advanced ignition technologies, and fuel delivery methods. The natural gas industry uses a variety of spark plugs and tuning methods to improve engine performance or decrease emissions of existing engines. The focus of this study was to examine the effects of various spark plug configurations along with spark timing to examine any potential benefits. Spark plugs with varied electrode diameter, number of ground electrodes, and heat ranges were evaluated against efficiency and exhaust emissions. Combustion analyses were also conducted to examine peak firing pressure, location of peak firing pressure, and indicated mean effective pressure. The test platform was an AJAX-E42 engine. The engine has a bore and stroke of 0.216 × 0.254 meters (m), respectively. The engine displacement was 9.29 liters (L) with a compression ratio of 6:1. The engine was modified to include electronic spark plug timing capabilities along with a mass flow controller to ensure accurate fuel delivery. Each spark plug configuration was examined at ignition timings of 17, 14, 11, 8, and 5 crank angle degrees before top dead center. The various configurations were examined to identify optimal conditions for each plug comparing trade-offs among brake specific fuel consumption, oxides of nitrogen, methane, formaldehyde, and combustion stability.

Comparison of Emissions and Efficiency of a Turbocharged Lean-Burn Natural Gas and Hythane-Fueled Engine

1997 ◽  
Vol 119 (1) ◽  
pp. 218-226 ◽  
Author(s):  
J. F. Larsen ◽  
J. S. Wallace
Keyword(s):  
Natural Gas ◽  
Specific Energy Consumption ◽  
Oxides Of Nitrogen ◽  
Heavy Duty ◽  
Lean Burn ◽  
Clear Trend ◽  
Engine Operation ◽  
Spark Timing ◽  
Test Engine ◽  
Carbon Dioxide Co2

An experiment was conducted to evaluate the potential for reduced exhaust emissions and improved efficiency, by way of lean-burn engine fuelling with hydrogen supplemented natural gas (Hythane). The emissions and efficiency of the Hythane fuel (15 percent hydrogen, 85 percent natural gas by volume), were compared to the emissions and efficiency of pure natural gas using a turbocharged, spark ignition, 3.1 L, V-6 engine. The feasibility of heavy duty engine fueling with Hythane was assessed through testing conducted at engine speed and load combinations typical of heavy-duty engine operation. Comparison of the efficiency and emissions at MBT spark timing revealed that Hythane fueling of the test engine resulted in consistently lower brake specific energy consumption and emissions of total hydrocarbons (THC), carbon monoxide (CO), and carbon dioxide (CO2), at a given equivalence ratio. There was no clear trend with respect to MBT oxides of nitrogen (NOx) emissions. It was also discovered that an improved NOx-THC tradeoff resulted when Hythane was used to fuel the test engine. Consequently, Hythane engine operating parameters can be adjusted to achieve a concurrent reduction in NOx and THC emissions relative to natural gas fueling.

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural Gas Spark Ignition

2018 ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Spark Timing ◽  
Heavy Duty Diesel

Increased utilization of natural-gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduce greenhouse-gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOx, CO, and HC emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing, engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late burn (including double-peak heat release rate) was observed for advanced spark timing. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3 %), moderate rate of pressure rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Heavy Duty Diesel ◽  
Ci Engines

Increased utilization of natural gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduced greenhouse gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOX, CO, and hydrocarbon (HC) emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing (ST), engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late-burn (including double-peak heat release rate) was observed for advanced ST. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3%), moderate rate of pressure-rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

Evaluation of a Lean-Burn Natural Gas Engine Operating on Variable Methane Number Fuel

2011 ◽  
Author(s):  
Cory J. Kreutzer ◽  
Daniel B. Olsen ◽  
Robin J. Bremmer
Keyword(s):  
Natural Gas ◽  
High Efficiency ◽  
Engine Performance ◽  
Combustion Stability ◽  
Lean Burn ◽  
Natural Gas Engines ◽  
Spark Timing ◽  
Gas Compression ◽  
Fuel Blending ◽  
Methane Number

Wellhead gas from which pipeline natural gas originates has significant variability in composition due to natural variations in deposits. Gas quality is influenced by relative concentrations of both inert and hydrocarbon species. Gas compression engines utilizing wellhead gas as a fuel source often require significant installation time and adjustment of stock configuration due to fuel compositions that vary with time and location. Lean burn natural gas engines are chosen as wellhead compression engines for high efficiency and low emissions while minimizing the effect of variable gas composition. Ideal engine conditions are maintained by operating within the knock and misfire limits of the engine. Additional data is needed to find engine operational limitations. In this work, experimental data was collected on a Cummins GTA8.3SLB engine operating on variable methane number fuel under closed-loop equivalence ratio control. A fuel blending system was used to vary methane number to simulate wellhead compositions. NOx and CO emissions were found to increase with decreasing methane number while combustion stability remained constant. In addition, the effects of carbon dioxide and nitrogen diluents in the fuel were investigated. When diluents were present in the fuel, engine performance could be maintained by spark timing advance.

scholarly journals Control-oriented analysis of a lean-burn light-duty natural gas research engine with scavenged pre-chamber ignition

2019 ◽  
Vol 176 (1) ◽  
pp. 42-53
Author(s):  
Severin HÄNGGI ◽  
Thomas HILFIKER ◽  
Patrik SOLTIC ◽  
Richard HUTTER ◽  
Christopher ONDER
Keyword(s):  
Natural Gas ◽  
Control Structure ◽  
Engine Performance ◽  
Combustion Stability ◽  
Performance Criteria ◽  
Transport Sector ◽  
Lean Burn ◽  
Fuel Ratio ◽  
Cng Engine ◽  
Lean Conditions

Natural gas is well-suited as a fuel in the transport sector. Due to its excellent combustion characteristics, engines operating with compressed natural gas (CNG) reach high efficiency, especially if operated at lean conditions. However, CNG engine research mainly focusses on stoichiometric conditions in order to use a three-way catalytic converter for the exhaust gas after treatment system. With the objective to explore the potential of CNG engines operated at lean conditions, a turbo-charged CNG engine with high com-pression ratio is developed and optimized for lean operation. In order to increase the ignition energy, the CNG engine is equipped with scavenged pre-chambers. A specific control structure is developed, which allows to operate the engine at a pre-defined (lean) air-to-fuel ratio. Further functionalities such as the combustion placement control and algorithms to estimate the conditions inside of the pre-chamber are implemented. The first part of this paper describes this engine control structure, which is specifically developed for the lean-burn CNG engine. In the second part, the effects of pre-chamber scavenging on engine performance criteria such as the combustion stability, engine efficiency or engine emissions are analyzed. With the objective to use pre-chamber scavenging to improve engine performance, a scavenging feed-back control strategy is proposed. In order to control the ignition delay, this strategy adapts the amount of CNG injected into the pre-chamber with a linear controller or an extremum seeking algorithm depending on the air-to-fuel ratio of the main chamber.

The Hybrid Rich-Burn/Lean-Burn Engine

1997 ◽  
Vol 119 (1) ◽  
pp. 243-249 ◽  
Author(s):  
D. P. Meyers ◽  
J. T. Kubesh
Keyword(s):  
Carbon Monoxide ◽  
Natural Gas ◽  
Combustion Stability ◽  
Lean Burn ◽  
Lean Mixture ◽  
Combustion Limits ◽  
Lean Limit ◽  
The Rich ◽  
Engine Concept ◽  
Combustion Exhaust

This paper describes a new low-emissions engine concept called the hybrid rich-burn/lean-burn (HRBLB) engine. In this concept a portion of the cylinders of a multicylinder engine are fueled with a very rich natural gas-air mixture. The remaining cylinders are operated with a lean mixture of natural gas and air and supplemented with the rich combustion exhaust. The goal of this unique concept is the production of extremely low NOx (e.g., 5 ppm when corrected to 15 percent exhaust oxygen content). This is accomplished by operating outside the combustion limits where NOx is produced. In rich combustion an abundance of hydrogen and carbon monoxide is produced. Catalyst treatment of the rich exhaust can be employed to increase the hydrogen concentration and decrease the carbon monoxide concentration simultaneously. The hydrogen-enriched exhaust is used to supplement the lean mixture cylinders to extend the lean limit of combustion, and thus produces ultralow levels of NOx. Results to date have shown NOx levels as low as 8 ppm at 15 percent oxygen can be achieved with good combustion stability and thermal efficiency.

Experimental Investigation of a Heavy-Duty CI Engine Retrofitted to Natural Gas SI Operation

2018 ◽  
Author(s):  
Jinlong Liu ◽  
Hemanth Bommisetty ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Operating Conditions ◽  
Intake Manifold ◽  
Heavy Duty ◽  
Lean Burn ◽  
Engine Operation ◽  
Cycle Variation ◽  
Spark Timing ◽  
Ci Engine ◽  
Ci Engines

Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late-combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.

Laser Spark Ignition: Laser Development and Engine Testing

2004 ◽  
Author(s):  
Michael H. McMillian ◽  
Steven D. Woodruff ◽  
Steven W. Richardson ◽  
Dustin L. McIntyre
Keyword(s):  
Natural Gas ◽  
Laser System ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Lean Burn ◽  
Engine Operation ◽  
Natural Gas Engines ◽  
Laser Spark ◽  
Engine Testing ◽  
Laser Spark Ignition

Evermore demanding market and legislative pressures require stationary lean-burn natural gas engines to operate at higher efficiencies and reduced levels of emissions. Higher in-cylinder pressures and leaner air/fuel ratios are required in order to meet these demands. Contemporary ignition systems, more specifically spark plug performance and durability, suffer as a result of the increase in spark energy required to maintain suitable engine operation under these conditions. This paper presents a discussion of the need for an improved ignition source for advanced stationary natural gas engines and introduces laser spark ignition as a potential solution to that need. Recent laser spark ignition engine testing with natural gas fuel including NOx mapping is discussed. A prototype laser system in constructed and tested and the results are discussed and solutions provided for improving the laser system output pulse energy and pulse characteristics.

Lean-Burn Stationary Natural Gas Reciprocating Engine Operation With a Prototype Fiber Coupled Diode End Pumped Passively Q-Switched Laser Spark Plug

2009 ◽  
Author(s):  
Dustin L. McIntyre ◽  
Steven D. Woodruff ◽  
John S. Ontko
Keyword(s):  
Natural Gas ◽  
Optical Fiber ◽  
Optical Power ◽  
Boost Pressure ◽  
Lean Burn ◽  
Engine Operation ◽  
Pump Source ◽  
Spark Plug ◽  
Spark Timing ◽  
Laser Spark

An end pumped passively Q-switched laser igniter was developed to meet the ignition system needs of large bore lean burn stationary natural gas engines. The laser spark plug used an optical fiber coupled diode pump source to axially pump a passively Q-switched Nd:YAG laser and transmit the laser pulse through a custom designed lens. The optical fiber coupled pump source permits the excitation energy to be transmitted to the spark plug at relatively low optical power, less than 250 watts. The Q-switched laser then generates as much as 8 millijoules of light in 2.5 nanoseconds which is focused through an asymmetric biconvex lens to create a laser spark from a focused intensity of approximately 225 GW/cm2. A single cylinder engine fueled with either natural gas only or hydrogen augmented natural gas was operated with the laser spark plug for approximately 10 hours in tests spanning 4 days. The tests were conducted with fixed engine speed, fixed boost pressure, no exhaust gas recirculation, and laser spark timing advance set at maximum brake torque timing. Engine operational and emissions data were collected and analyzed.

Sign in / Sign up

Export Citation Format

Share Document