Residual Stress Measurements in an Autofrettage Tube Using Hole Drilling Method

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Hamid Jahed ◽  
Mohammad Reza Faritus ◽  
Zeinab Jahed
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Hoop Stress ◽  
Test Method ◽  
Test Material ◽  
Hole Drilling ◽  
Hole Drilling Method ◽  
Ring Sample ◽  
Drilling Method ◽  
American Society

Relieved strains due to drilling hole in a ring sample cut from an autofrettage cylinder are measured. Measured strains are then transformed to residual stresses using calibration constants and mathematical relations of elasticity based on ASTM standard recommendations (American Society for Testing and Materials, ASTM E 837-08, 2008, “Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method,” American Society for Testing and Materials). The hydraulic autofrettage is pressurizing a closed-end long cylinder beyond its elastic limits and subsequently removing the pressure. In contrast to three-dimensional stress state in the autofrettage tube, the stress measurement in hole drilling method is performed on a traction free surface formed from cutting the ring sample. The process of cutting the ring sample from a long autofrettaged tube is simulated using finite element method (FEM) and the redistribution of the residual stress due to the cut is discussed. Hence, transformation of the hole drilling measurements on the ring slice to the autofrettage residual stresses is revealed. The residual stresses are also predicted by variable material properties (VMP) method (Jahed, H., and Dubey, R. N., 1997, “An Axisymmetric Method of Elastic-Plastic Analysis Capable of Predicting Residual Stress Field,” Trans. ASME J. Pressure Vessel Technol., 119, pp. 264–273) using real loading and unloading behavior of the test material. Prediction results for residual hoop stress agree very well with the measurements. However, radial stress predictions are less than measured values particularly in the middle of the ring. To remove the discrepancy in radial residual stresses, the measured residual hoop stress that shows a self-balanced distribution was taken as the basis for calculating residual radial stresses using field equations of elasticity. The obtained residual stresses were improved a lot and were in good agreement with the VMP solution.

Modeling and Measurement of Residual Stresses along the Process Chain of Autofrettaged Components by Using FEA and Hole-Drilling Method with ESPI

2013 ◽  
Vol 768-769 ◽  
pp. 79-86 ◽  
Author(s):  
Horst Brünnet ◽  
Dirk Bähre ◽  
Theo J. Rickert ◽  
Dominik Dapprich
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Speckle Pattern ◽  
Residual Stress Distribution ◽  
Electronic Speckle Pattern Interferometry ◽  
Hole Drilling ◽  
Element Analysis ◽  
Hole Drilling Method ◽  
Drilling Method

The incremental hole-drilling method is a well-known mechanical measurement procedure for the analysis of residual stresses. The newly developed PRISM® technology by Stresstech Group measures stress relaxation optically using electronic speckle pattern interferometry (ESPI). In case of autofrettaged components, the large amount of compressive residual stresses and the radius of the pressurized bores can be challenging for the measurement system. This research discusses the applicability of the measurement principle for autofrettaged cylinders made of steel AISI 4140. The residual stresses are measured after AF and after subsequent boring and reaming. The experimental residual stress depth profiles are compared to numerically acquired results from a finite element analysis (FEA) with the software code ABAQUS. Sample preparation will be considered as the parts have to be sectioned in half in order to access the measurement position. Following this, the influence of the boring and reaming operation on the final residual stress distribution as well as the accuracy of the presented measurement setup will be discussed. Finally, the usability of the FEA method in early design stages is discussed in order to predict the final residual stress distribution after AF and a following post-machining operation.

Determination of Residual Stresses in Medium Density Fibreboard

Holzforschung ◽  
2000 ◽  
Vol 54 (2) ◽  
pp. 176-182 ◽  
Author(s):  
Jeroen van Houts ◽  
Debes Bhattacharyya ◽  
Krishnan Jayaraman
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Thickness Swell ◽  
Hole Drilling ◽  
Medium Density ◽  
Stress Distributions ◽  
Moisture Expansion ◽  
Hole Drilling Method ◽  
Drilling Method ◽  
Residual Internal Stress

Summary Due to the moisture and temperature gradients developed during hot pressing of medium density fibre-board (MDF), residual stresses occur within the board as it equilibrates to room conditions. It would be extremely useful to measure these residual stresses and to determine their effects on board properties such as moduli of elasticity and rupture in bending, internal bond strength and dimensional stability. In this article two methods, namely dissection and hole drilling, have been adapted to measure residual internal stress distributions in six different samples of industry produced MDF. The dissection method involves cutting several pieces of MDF perpendicular to the thickness direction at different depths. The residual stresses released by the dissection can be determined by measuring the curvatures of cut pieces and knowing their elastic moduli. The hole drilling method, on the other hand, involves mounting three strain gauges on the surface of a piece of MDF and drilling a hole to release residual stresses in close proximity. The released stresses are manifested as strains in the forms of which can be measured in three directions on the surface of the board. A theoretical model for predicting residual stresses involving various parameters has been developed and an excellent agreement with the experimental results from both the dissection and hole drilling methods has been achieved. Linear moisture expansion coefficient appears to have the greatest influence on residual stress. When compared against each other, the residual stresses measured by the hole drilling method show some shortcomings towards the centre of the board. While all six of the MDF boards exhibited similar trends in their residual stress distributions, significant differences were identified in the magnitudes of residual stress measured. Finally, some preliminary results linking the residual stress with the thickness swell of the samples and their surface densities have been presented.

Hole-Drilling Method for Residual Stress Measurement - Consideration of Elastic-Plastic Material Properties

2013 ◽  
Vol 768-769 ◽  
pp. 174-181 ◽  
Author(s):  
David von Mirbach
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Yield Stress ◽  
Material Properties ◽  
Plastic Material ◽  
Hole Drilling ◽  
Hole Drilling Method ◽  
Drilling Method ◽  
Elastic Plastic Material ◽  
Ring Core

Two commonly used mechanical methods for the determination of residual stresses are the hole-drilling method and the ring-core method, which can be regarded as semi-destructive. The most restricting limitation for the general applicability of both methods, according to the current state of science and technology, is the fact that the scope for relatively low residual stress under 60% of the yield stress is limited.This is a result of the notch effect of the hole or ring core, which leads to a plastification around and on the bottom of the hole and ring shaped groove already at stresses well below the yield stress of the material. The elastic evaluation of the resulting plastic strains leads consequently to an overestimation of the delineated residual stresses. In this paper the influence of elastic-plastic material properties no the specific calibration function for the hole-drilling method using the differential method is studied, and the method of adaptive calibration functions is presented.

Inverse Hole-Drilling Method for Residual Stress Investigation

2016 ◽  
Vol 827 ◽  
pp. 117-120
Author(s):  
Jaroslav Vaclavik ◽  
Stanislav Holy ◽  
Jiří Jankovec ◽  
Petr Jaros ◽  
Otakar Weinberg
Keyword(s):  
Residual Stress ◽  
Numerical Modeling ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Hole Drilling ◽  
Back Side ◽  
Stress Evaluation ◽  
Hole Drilling Method ◽  
Drilling Method ◽  
Strain Gauge Rosette

The method for residual stress measurement using through the hole drilling and investigation of the residual stresses relief with the help of incremental layers removing is presented. Drilling the rosette-hole from the opposite side – the inverse layers removing – have to be used for evaluation of residual stress near the back side of the object wall in cases when this surface is inaccessible for any hole-drilling instrument. The strain gauge rosette is installed on the opposite side of the drilled wall and a new mechanical task of incremental layers removal must be solved. The calibration constants for residual stress evaluation of HBM RY21 type rosette for this case were derived using numerical modeling by FEA and its experimental verification.

The Influence of Chemical Composition on Residual Stresses in NiCoMo Alloy Deposits on 12 Ni Maraging Steel

2013 ◽  
Vol 768-769 ◽  
pp. 449-455 ◽  
Author(s):  
Zoran Bergant ◽  
Janez Grum
Keyword(s):  
Residual Stress ◽  
Chemical Composition ◽  
Residual Stresses ◽  
Base Material ◽  
Stress Generation ◽  
Hole Drilling ◽  
Residual Stress Field ◽  
Hole Drilling Method ◽  
Similar Chemical ◽  
Drilling Method

The in-plane residual stresses in laser cladded specimens, made of 12-nickel precipitation hardening maraging hot-working tool steel 1.2799 (SIST EN 10027-2) are analyzed using the hole drilling method. The CO2 laser was used to deposit the alloy NiCoMo-1 with significantly higher content of nickel and cobalt with austenitic microstructure at room temperature. The Nd:YAG laser was used to deposit the maraging alloy designated NiCoMo-2, with similar chemical composition as the base material. The comparison of residual stress field showed the sign and the magnitude of residual stresses depends on the chemical composition of the clad being deposited. The high tensile residual stresses were found in NiCoMo-1 layers and favorable compressive residual stresses were found in NiCoMo-2 layers. The metallurgical aspects of residual stress generation are discussed.

Eliminating plasticity effects in the measurement of residual stress by using the hole-drilling method

2021 ◽  
Vol 63 (3) ◽  
pp. 219-225
Author(s):  
Ying Gu ◽  
Songbo Ren ◽  
Chao Kong ◽  
Song Gu
Keyword(s):  
Residual Stress ◽  
Iterative Method ◽  
Principal Stress ◽  
Experimental Studies ◽  
Maximum Principal Stress ◽  
Elastic Behavior ◽  
Hole Drilling ◽  
Hole Drilling Method ◽  
Drilling Method ◽  
American Society

Abstract When the hole-drilling method is used to measure residual stress, plasticity effects occur if the residual stress exceeds 60 % of the yield stress. Plasticity effects result in an overestimation of the residual stress as the hole-drilling method is based on the linear elastic behavior of materials. To overcome this problem, a simplified iterative method based on an existing iterative method and using the optimizer tools of the ANSYS program is proposed in this paper. The proposed method is verified through numerical and experimental studies. The numerical case study reveals that, for the case studied, the proposed method can achieve the same accuracy as the original iterative method and has a higher convergence ability. The experimental study demonstrates that the values of the maximum principal stress calculated using the American Society of Testing Materials standard is generally greater than the true values and that the error magnitude increases with an increase in stress levels. Using the proposed method, errors are reduced for the maximum principal stress while increasing slightly for the minimum principal stress. The proposed method has a high convergence ability; for the case studied, only two or three iterations are needed to achieve acceptable accuracy.

Residual Stresses in Steel-Titanium Composite Manufactured by Explosive Welding

2012 ◽  
Vol 726 ◽  
pp. 125-132 ◽  
Author(s):  
Aleksander Karolczuk ◽  
Krzysztof Kluger ◽  
Mateusz Kowalski ◽  
Fabian Żok ◽  
Grzegorz Robak
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Residual Stresses ◽  
Hole Drilling ◽  
Element Analysis ◽  
Welded Steel ◽  
Hole Drilling Method ◽  
Drilling Method ◽  
Before And After ◽  
Stress States

The main aim of the paper is determination of residual stresses in explosively welded steel-titanium bimetal. The analysis considers two bimetallic specimens: before and after the heat treatment. In residual stress determination the hole drilling method along with finite element analysis were applied. The results show different residual stress states depending on the heat treatment. The obtained results are confirmed by thermal stress calculation.

The Application of the Hole Drilling Method to Define the Residual Stress of Dissimilar Laser Welded Components

2007 ◽  
Vol 7-8 ◽  
pp. 133-138 ◽  
Author(s):  
E.M. Anawa ◽  
Abdul Ghani Olabi
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Laser Welding ◽  
Power Plants ◽  
Welding Process ◽  
Hole Drilling ◽  
Welding Parameters ◽  
Heating Process ◽  
Hole Drilling Method ◽  
Drilling Method

Dissimilar metal welds between Ferritic steel and Austenitic steel (F/A)are commonly used in power plants, food industry, pharmaceutical industry and many other applications. There are many issues/problems associated with the joining of dissimilar materials, depending on the materials being joined and the process selected. During the laser welding process, residual stresses are introduced by a rise in temperature during the melting or heating process followed by a very quick cooling of the weld and the surrounding material. In this study, CO2 continuous laser welding has been successfully applied for joining 316 stainless steel with AISI 1009 low carbon steel F/A. Design of Experiment techniques (DOE) has been used for some of the selected welding parameters (laser power, welding speed, and focus position) to model the dissimilar F/A joints in terms of its residual stresses. The Hole-Drilling Method technique was use for measuring the residual stress of dissimilar welded components. Taguchi approach for selected welding parameters was applied and the output response was the residual stresses. The results were analysed using analysis of variance (ANOVA) and signal-tonoise (S/N) ratios for the effective parameters combination.

Reduce the Residual Stress of Welded Structures by Post-Weld Vibration

2005 ◽  
Vol 490-491 ◽  
pp. 102-106 ◽  
Author(s):  
De Lin Rao ◽  
Zheng Qiang Zhu ◽  
Li Gong Chen ◽  
Chunzhen Ni
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Residual Stresses ◽  
Mechanical Vibration ◽  
Welding Process ◽  
Hole Drilling ◽  
Welded Structures ◽  
Hole Drilling Method ◽  
Drilling Method ◽  
Before And After

The existence of residual stresses caused by the welding process is an important reason of cracking and distortion in welded metal structures that may affect the fatigue life and dimensional stability significantly. Heat treatment is one of the traditional methods to relieve the residual stresses. But it is often limited by the manufacturing condition and the size of the structures. In this paper a procedure called vibratory stress relief (VSR) is discussed. VSR is a process to reduce and re-distribute the internal residual stresses of welded structures by means of post-weld mechanical vibration. The effectiveness of VSR on the residual stresses of welded structures, including the drums of hoist machine and thick stainless steel plate are investigated. Parameters of VSR procedure are described in the paper. Residual stresses on weld bead are measured before and after VSR treatment by hole-drilling method and about 30%~50% reduction of residual stresses are observed. The results show that VSR process can reduce the residual stress both middle carbon steel (Q345) and stainless steel (304L) welded structures effectively.

Application of Hole-Drilling Method in Practice

2006 ◽  
Vol 524-525 ◽  
pp. 555-560 ◽  
Author(s):  
Bojan Podgornik ◽  
Joze Vižintin ◽  
Franci Kopač
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Hole Drilling ◽  
Machine Component ◽  
Practical Applications ◽  
Hole Drilling Method ◽  
Precise Knowledge ◽  
Drilling Method ◽  
Proper Design ◽  
Treatment Procedures

Residual stresses can arise in engineering components as part of their manufacturing or can also be introduced deliberately as part of surface treatment procedures. A precise knowledge of the level of residual stresses that exist in engineering components is necessary in analysis and quality control as well as for accurate prediction of components lifetime. Therefore, reliable methods of determining the magnitude and distribution of residual stresses are required in order to quantify their effect and to avoid detrimental failures. On the other hand on-site portable and nonor near non-destructive methods are required for practical use. The hole-drilling method shows a great potential in measuring and evaluating residual stresses in practical applications. This paper presents results and problems on residual stress measurements performed by the holedrilling method on real components, including forming applications of rolling, punching and cutting, and machine component applications of gears and shafts. Presented results clearly indicate the importance of residual stress information for proper design and use of engineering components.

Sign in / Sign up

Export Citation Format

Share Document