On the Damping in Tube Arrays Subjected to Two-Phase Cross-Flow

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
J. E. Moran ◽  
D. S. Weaver
Keyword(s):  
Flow Regime ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Cross Flow ◽  
Working Fluid ◽  
Exponential Fitting ◽  
Phase Flow ◽  
Two Phase ◽  
Tube Arrays ◽  
Half Power

An experimental study was conducted to investigate the mechanism of damping in tube arrays subjected to two-phase cross-flow, mainly focusing on the influence of void fraction and flow regime. The model tube bundle had a parallel-triangular configuration, with a pitch ratio of 1.49. The two-phase flow loop used in this research utilized Refrigerant 11 as the working fluid, which better models steam-water than air-water mixtures in terms of vapour-liquid mass ratio as well as permitting phase changes due to pressure fluctuations. The void fraction was measured using a gamma densitometer, introducing an improvement over the homogeneous equilibrium model (HEM). Three different damping measurement methodologies were implemented and compared in order to obtain a more reliable damping estimate: the traditionally used half-power bandwidth, the logarithmic decrement and an exponential fitting to the tube decay response. The experiments showed that the half-power bandwidth produces higher damping values than the other two methods, due to the tube frequency shifting triggered by fluctuations in the added mass and coupling between the tubes, which depend on void fraction and flow regime. The exponential fitting proved to be the more consistent and reliable approach to estimating damping. A dimensional analysis was carried out to investigate the relationship between damping and two-phase flow related parameters. As a result, the inclusion of surface tension in the form of the capillary number appears to be useful when combined with the two-phase component of the damping ratio (interfacial damping). A strong dependence of damping on flow regime was observed when plotting the interfacial damping versus the void fraction, introducing an improvement over the previous results obtained by normalizing the two-phase damping, which does not exhibit this behavior.

scholarly journals Damping Measurements in Tube Bundles Subjected to Two-Phase Cross Flow

2006 ◽  
Author(s):  
Joaquin E. Moran ◽  
David S. Weaver
Keyword(s):  
Flow Regime ◽  
Void Fraction ◽  
Mass Flux ◽  
Damping Ratio ◽  
Logarithmic Decrement ◽  
Working Fluid ◽  
Exponential Fitting ◽  
Two Phase ◽  
Tube Bundles ◽  
Half Power

An experimental study was conducted to investigate two-phase damping in tube arrays. The objective was to compare different measurement methodologies in order to obtain a more reliable damping estimate. This will allow for improved guidelines related to failures due to fluidelastic instability in tube bundles. The methods compared were the traditionally used half-power bandwidth, the logarithmic decrement and an exponential fitting to the tube decay response. The working fluid used was Refrigerant 11 (Freon), which better models the real steam-water problem, as it allows for phase change. The void fraction was measured using a gamma densitometer, introducing an improvement over the traditional Homogeneous Equilibrium Model (HEM) in terms of velocity and density predictions. The results obtained by using the half-power bandwidth method agree with data previously reported for two-phase flow. The experiments showed that the half-power bandwidth produces higher damping values than the other two, but only up to a certain void fraction. After that point, the results obtained from the three methods are very similar. The exponential fitting proved to be more consistent than the logarithmic decrement, and it is not as sensitive as the half-power bandwidth to the frequency shifting caused by the change in added mass around the tube. By plotting the damping ratio as a function of void fraction, pitch mass flux and flow regime, we were able to verify that damping is more dependent on void fraction and flow regime than on mass flux.

scholarly journals On Damping and Fluidelastic Instability in a Tube Bundle Subjected to Two-Phase Cross-Flow

2007 ◽  
Author(s):  
Joaquin E. Moran ◽  
David S. Weaver
Keyword(s):  
Flow Regime ◽  
Void Fraction ◽  
Tube Bundle ◽  
Damping Ratio ◽  
Pressure Fluctuations ◽  
Cross Flow ◽  
Phase Changes ◽  
Working Fluid ◽  
Two Phase ◽  
Fluidelastic Instability

An experimental study was conducted to investigate damping and fluidelastic instability in tube arrays subjected to two-phase cross-flow. The purpose of this research was to improve our understanding of these phenomena and how they are affected by void fraction and flow regime. The working fluid used was Freon 11, which better models steam-water than air-water mixtures in terms of vapour-liquid mass ratio as well as permitting phase changes due to pressure fluctuations. The damping measurements were obtained by “plucking” the monitored tube from outside the test section using electromagnets. An exponential function was fitted to the tube decay trace, producing consistent damping measurements and minimizing the effect of frequency shifting due to fluid added mass fluctuations. The void fraction was measured using a gamma densitometer, introducing an improvement over the Homogeneous Equilibrium Model (HEM) in terms of density and velocity predictions. It was found that the Capillary number, when combined with the two-phase damping ratio (interfacial damping), shows a well defined behaviour depending on the flow regime. This observation can be used to develop a better methodology to normalize damping results. The fluidelastic results agree with previously presented data when analyzed using the HEM and the half-power bandwidth method. The interfacial velocity is suggested for fluidelastic studies due to its capability for collapsing the fluidelastic data. The interfacial damping was introduced as a tool to include the effects of flow regime into the stability maps.

Effect of Void Fraction on Vibrational Behavior of Tubes in Tube Bundle Under Two-Phase Cross Flow

1997 ◽  
Vol 119 (3) ◽  
pp. 457-463 ◽  
Author(s):  
H. Y. Lian ◽  
G. Noghrehkar ◽  
A. M. C. Chan ◽  
M. Kawaji
Keyword(s):  
Void Fraction ◽  
Two Phase Flow ◽  
Tube Bundle ◽  
Dynamic Pressure ◽  
Damping Ratio ◽  
Cross Flow ◽  
Vibration Measurement ◽  
Phase Flow ◽  
Two Phase ◽  
Vibrational Behavior

The effects of local two-phase flow parameters on the vibrational behavior of tubes have been studied in an in-line 5 × 20 tube bundle subjected to air-water cross-flow. One of the tubes was flexibly mounted and instrumented for vibration measurement and the others were rigid. Parameters obtained include local void fraction fluctuations, RMS amplitude of void fraction fluctuations, void fraction distributions across the tube bundle, flow regimes based on probability density function of void fraction signals, damping ratio, and tube vibration response as a function of mass flux, void fraction and dynamic pressure. Damping and tube vibration amplitude in two-phase flow have been found to be closely related to the RMS amplitudes of the local void fraction fluctuations and dynamic pressure fluctuations, respectively.

Development of a Capacitance Based Void Fraction Sensor for Two-Phase Flow Measurements

2013 ◽  
Author(s):  
Rodward L. Hewlin ◽  
John P. Kizito
Keyword(s):  
Void Fraction ◽  
Two Phase Flow ◽  
Full Range ◽  
Working Fluid ◽  
Phase Flow ◽  
Calibration Data ◽  
Two Phase ◽  
Flow Measurements ◽  
Static Calibration ◽  
Wide Range

The aim of this paper was to develop a capacitance based sensor capable of measuring void fraction in a continuous two-phase flow field. The design methodology and operation of the capacitance based void fraction sensor is discussed. Two designs of capacitance void fraction sensors were developed and tested. Some of the problems associated with the first were identified and a new sensor electrode configuration was developed which presented a more sensitive and repeatable response. Data was collected covering a wide range of void fraction measurements ranging from 0 to 1 for water as the working fluid. Calibration of the sensor required that the air gap or void capacitance (dry signal) be measured followed by an increase in liquid levels (wet signal) to obtain a range of void fraction measurements for static calibration. The static calibration data obtained was nonlinear for the full range of void fraction measurements for water. This paper covers the design requirements, calibration procedure and static calibration data obtained for the developed sensor, and dynamic void fraction data measurements. The sensor was tested in both a horizontal and vertical orientation and proved to be orientation insensitive. The experimental results are promising for water and verify successful operation for measuring void fraction in continuous two-phase flows.

Two-Phase Flow-Induced Vibration of Parallel Triangular Tube Arrays With Asymmetric Support Stiffness

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Paul Feenstra ◽  
David S. Weaver ◽  
Tomomichi Nakamura
Keyword(s):  
Two Phase Flow ◽  
Cross Flow ◽  
Phase Flow ◽  
Heat Exchanger Tube ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Tube Arrays ◽  
Tube Bundles ◽  
Pitch Ratio ◽  
Exchanger Tube

Laboratory experiments were conducted to determine the flow-induced vibration response and fluidelastic instability threshold of model heat exchanger tube bundles subjected to a cross-flow of refrigerant 11. Tube bundles were specially built with tubes cantilever-mounted on rectangular brass support bars so that the stiffness in the streamwise direction was about double that in the transverse direction. This was designed to simulate the tube dynamics in the U-bend region of a recirculating-type nuclear steam generator. Three model tube bundles were studied, one with a pitch ratio of 1.49 and two with a smaller pitch ratio of 1.33. The primary intent of the research was to improve our understanding of the flow-induced vibrations of heat exchanger tube arrays subjected to two-phase cross-flow. Of particular concern was to compare the effect of the asymmetric stiffness on the fluidelastic stability threshold with that of axisymmetric stiffness arrays tested most prominently in literature. The experimental results are analyzed and compared with existing data from literature using various definitions of two-phase fluid parameters. The fluidelastic stability thresholds of the present study agree well with results from previous studies for single-phase flow. In two-phase flow, the comparison of the stability data depends on the definition of two-phase flow velocity.

scholarly journals On the use of area-averaged void fraction and local bubble chord length entropies as two-phase flow regime indicators

2010 ◽  
Vol 49 (5) ◽  
pp. 1147-1160
Author(s):  
Leonor Hernández ◽  
J. Enrique Juliá ◽  
Sidharth Paranjape ◽  
Takashi Hibiki ◽  
Mamoru Ishii
Keyword(s):  
Flow Regime ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Chord Length ◽  
Phase Flow ◽  
Two Phase ◽  
Local Bubble

Impedance-Based Void Fraction Measurement and Flow Regime Identification in Microchannel Flows

2011 ◽  
Author(s):  
Sidharth Paranjape ◽  
Susan N. Ritchey ◽  
Suresh V. Garimella
Keyword(s):  
Flow Regime ◽  
Void Fraction ◽  
High Speed ◽  
Electrical Impedance ◽  
Two Phase Flow ◽  
Phase Distribution ◽  
Electrical Conductance ◽  
Statistical Characteristics ◽  
Phase Flow ◽  
Two Phase

Electrical impedance of a two-phase mixture is a function of void fraction and phase distribution. The difference in the electrical conductance and permittivity of the two phases can be exploited to measure electrical impedance for obtaining void fraction and flow regime characteristics. An electrical impedance meter is constructed for the measurement of void fraction in microchannel two-phase flow. The experiments are conducted in air-water two-phase flow under adiabatic conditions. A transparent acrylic test section of hydraulic diameter 780 micrometer is used in the experimental investigation. The impedance void meter is calibrated against the void fraction measured using analysis of images obtained with a high-speed camera. Based on these measurements, a methodology utilizing the statistical characteristics of the void fraction signals is employed for identification of microchannel flow regimes.

Correlation between Void Fraction and Two-Phase Flow Pattern Air-Water with Low Viscosity in Mini Channel with Slope 30 Degrees

2020 ◽  
Vol 846 ◽  
pp. 289-295
Author(s):  
Sukamta ◽  
Sudarja
Keyword(s):  
Void Fraction ◽  
High Speed ◽  
Two Phase Flow ◽  
Fluid Velocity ◽  
Flow Patterns ◽  
Superficial Velocity ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Void Fractions

Two-phase flow has been used in so many industrial processes, such as boilers, reactors, heat exchangers, geothermal and others. Some parameters which need to be studied include flow patterns, void fractions, and pressure changes. Research on void fractions aims to determine the composition of the gas and liquid phases that will affect the nature and value of the flow property. The purpose of this study is to find out the characteristics of the void fraction of various patterns that occurs and to determine the characteristics of the velocity, length, and frequency of bubbly and plug. Data acquisition was used to convert the data from analog to digital so that it can be recorded, stored, processed, and analyzed. High-speed camera Nikon type J4 was used to record the flow. The condition of the study was adiabatic with variation of superficial gas velocity (JG), superficial fluid velocity (JL), and also working fluid. To determine the void fraction by using the digital image processing method. The results of the study found that the flow patterns which occurred in this study were bubbly, plug, annular, slug-annular and churn flows. It also showed that the void fraction value is determined by the superficial velocity of the liquid and air. The higher the superficial velocity of the air, the lower the void fraction value.

Sign in / Sign up

Export Citation Format

Share Document