Plastic Load of Precracked Polyethylene Miter Pipe Bends Subjected to In-Plane Bending Moment1

2013 ◽  
Vol 135 (6) ◽  
Author(s):  
Tarek M. A. A. EL-Bagory ◽  
Maher Y. A. Younan ◽  
Hossam E. M. Sallam ◽  
Lotfi A. Abdel-Latif
Keyword(s):  
Crack Depth ◽  
Testing Machine ◽  
Bending Moment ◽  
Factor H ◽  
Bend Angle ◽  
Pipe Bend ◽  
Obvious Effect ◽  
Linear Elastic ◽  
Piping Systems ◽  
Plane Bending

The main purpose of the present paper is to investigate the effect of crack depth on the plastic load (collapse load) of miter pipe bends (MPB) under in-plane bending moment. The experimental work is conducted to investigate multimiter pipe bends, with a bend angle 90 deg, pipe bend factor h = 0.844, standard dimension ratio (SDR) = 11, and number of welding junctions m = 3 under a crosshead speed 500 mm/min. The material of the investigated pipe is a high-density polyethylene (HDPE), which is used in natural gas (NG) piping systems. The welds in the miter pipe bends are produced by butt-fusion method. The crack depth varies from intrados to extrados location according to the in-plane opening/closing bending moment, respectively. For each in-plane bending moment, the plastic load is obtained by the tangent intersection (TI) method from the load–deflection curves produced by the testing machine specially designed and constructed in the laboratory.5 The study reveals that increasing the crack depth leads to a decrease in the stiffness and plastic load of MPB for both in-plane closing and opening bending moment. Higher values of the plastic load are reached in case of opening bending moment. This behavior is true for all investigated crack depths. A circumferential external crack has an obvious effect on the behavior of load–deflection curve. The linear elastic region in both mode of loading decreases with increasing crack depth.

Limit Load of Pre-Cracked Polyethylene Miter Pipe Bends Subjected to In-Plane Bending Moment

2010 ◽  
Author(s):  
Tarek M. A. A. EL-Bagory ◽  
Maher Y. A. Younan ◽  
Hossam E. M. Sallam ◽  
Lotfi A. Abdel-Latif
Keyword(s):  
High Density Polyethylene ◽  
Crack Depth ◽  
Testing Machine ◽  
Bending Moment ◽  
Limit Load ◽  
Factor H ◽  
Bend Angle ◽  
Pipe Bend ◽  
Piping Systems ◽  
Plane Bending

The main purpose of the present paper is to investigate the effect of crack depth on the limit load of miter pipe bends (MPB) under in-plane bending moment. The experimental work is conducted to investigate multi miter pipe bends, with a bend angle 90°, pipe bend factor h = 0.844, standard dimension ratio SDR = 11, and three junctions under a crosshead speed 500 mm/min. The material of the investigated pipe is a high-density polyethylene (HDPE), which is used in natural gas piping systems. The welds in the miter pipe bends are produced by butt-fusion method. The crack depth varies from intrados to extrados location according to the in-plane opening/closing bending moment respectively. For each in-plane bending moment the limit load is obtained by the tangent intersection (TI) method from the load deflection curves produced by the testing machine specially designed and constructed in the laboratory. The study reveals that increasing the crack depth leads to a decrease in the stiffness and limit load of (MPB) for both inplane closing and opening bending moment. Higher values of the limit load are reached in case of opening bending moment. This behavior is true for all investigated crack depths.

Effect of Load Angle on Limit Load of Polyethylene Miter Pipe Bends

2010 ◽  
Author(s):  
Tarek M. A. A. EL-Bagory ◽  
Maher Y. A. Younan ◽  
Hossam E. M. Sallam ◽  
Lotfi A. Abdel-Latif
Keyword(s):  
Crack Depth ◽  
Bending Moment ◽  
Limit Load ◽  
Factor H ◽  
Pipe Bend ◽  
Combined Load ◽  
Specific Loading ◽  
Out Of Plane ◽  
Plane Bending ◽  
Load Angle

The aim of this paper is to investigate the effect crack depth a/W = 0 to 0.4 and load angle (30°,45°,and 60°) on the limit load of miter pipe bends (MPB) under out-of-plane bending moment with a crosshead speed 500 mm/min. The geometry of cracked and uncracked multi miter pipe bends are: bend angle, α = 90°, pipe bend factor, h = 0.844, standard dimension ratio, SDR = 11, and three junctions, m = 3. The material of the investigated pipe is a high-density polyethylene (HDPE), which is applied in natural gas piping systems. Butt-fusion welding is used to produce the welds in the miter pipe bends. An artificial crack is produced by a special cracking device. The crack is located at the crown side of the miter pipe bend, such that the crack is collinear with the direction of the applied load. The crack depth ratio, a/W = 0, 0.1, 0.2, 0.3 and 0.4 for out-of-plane bending moment “i.e. loading angle φ = 0°”. For each out-of-plane bending moment and all closing and opening load angles the limit load is obtained by the tangent intersection method (TI) from the load deflection curves produced by the specially designed and constructed testing machine at the laboratory. For each out-of-plane bending moment case, the experimental results reveals that increasing crack depth leads to a decrease in the stiffness and limit load of MPB. In case of combined load (out-of-plane and in-plane opening; mode) higher load angles lead to an increase in the limit load. The highest limit load value appears at a loading angle equal, φ = 60°. In case of combined load (out-of-plane and in-plane closing; mode) the limit load decreases upon increasing the load angle. On the other hand, higher limit load values take place at a specific loading angle equal φ = 30°. For combined load opening case; higher values of limit load are obtained. Contrarily, lower values are obtained in the closing case.

Effect of Load Angle on Limit Load of Polyethylene Miter Pipe Bends1

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Tarek M. A. A. EL-Bagory ◽  
Maher Y. A. Younan ◽  
Hossam E. M. Sallam ◽  
Lotfi A. Abdel-Latif
Keyword(s):  
Crack Depth ◽  
Bending Moment ◽  
Limit Load ◽  
Factor H ◽  
Pipe Bend ◽  
Combined Load ◽  
Specific Loading ◽  
Out Of Plane ◽  
Plane Bending ◽  
Load Angle

The aim of this paper is to investigate the effect of crack depth a/W = 0–0.4 and load angle (30 deg, 45 deg, and 60 deg) on the limit load of miter pipe bends (MPB) under out-of-plane bending moment with a crosshead speed 500 mm/min. The geometry of cracked and un-cracked multi miter pipe bends are: bend angle, α = 90 deg, pipe bend factor, h = 0.844, standard dimension ratio, SDR = 11, and three junctions, m = 3. The material of the investigated pipe is a high-density polyethylene (HDPE), which is applied in natural gas piping systems. Butt-fusion welding is used to produce the welds in the miter pipe bends. An artificial crack is produced by a special cracking device. The crack is located at the crown side of the miter pipe bend, such that the crack is collinear with the direction of the applied load. The crack depth ratio, a/W = 0, 0.1, 0.2, 0.3, and 0.4 for out-of-plane bending moment “i.e., loading angle ϕ = 0 deg”. For each out-of-plane bending moment and all closing and opening load angles the limit load is obtained by the tangent intersection method (TI) from the load deflection curves produced by the specially designed and constructed testing machine at the laboratory (Mechanical Design Department, Faculty of Engineering, Mataria, Helwan University, Cairo/Egypt). For each out-of-plane bending moment case, the experimental results reveals that increasing crack depth leads to a decrease in the stiffness and limit load of MPB. In case of combined load (out-of-plane and in-plane opening; mode) higher load angles lead to an increase in the limit load. The highest limit load value appears at a loading angle equal, ϕ = 60 deg. In case of combined load (out-of-plane and in-plane closing; mode) the limit load decreases upon increasing the load angle. On the other hand, higher limit load values appear at a specific loading angle equal ϕ = 30 deg. For combined load opening case; higher values of limit load are obtained. Contrarily, lower values are obtained in the closing case.

Investigation of Smooth Pipe Bends Under the Effect of In-Plane Bending

2017 ◽  
Author(s):  
Diana Abdulhameed ◽  
Michael Martens ◽  
J. J. Roger Cheng ◽  
Samer Adeeb
Keyword(s):  
High Stress ◽  
Circular Cross Section ◽  
Bending Moment ◽  
Bend Angle ◽  
Bending Moments ◽  
Bend Radius ◽  
Pipe Bend ◽  
Cross Sectional ◽  
Smooth Pipe ◽  
Plane Bending

Pipe bends are frequently used to change the direction in pipeline systems and they are considered one of the critical components as well. Bending moments acting on the pipe bends result from the surrounding environment, such as thermal expansions, soil deformations, and external loads. As a result of these bending moments, the initially circular cross-section of the pipe bend deforms into an oval shape. This consequently changes the pipe bend’s flexibility leading to higher stresses compared to straight pipes. Past studies considered the case of a closing in-plane bending moment on 90-degree pipe bends and proposed factors that account for the increased flexibility and high-stress levels. These factors are currently presented in the design codes and known as the flexibility and stress intensification factors (SIF). This paper covers the behaviour of an initially circular cross-sectional smooth pipe bend of uniform thickness subjected to in-plane opening/closing bending moment. ABAQUS FEA software is used in this study to model pipe bends with different nominal pipe sizes, bend angles, and various bend radius to cross-sectional pipe radius ratios. A comparison between the CSA-Z662 code and the FEA results is conducted to investigate the applicability of the currently used SIF factor presented in the design code for different loading cases. The study showed that the in-plane bending moment direction acting on the pipe has a significant effect on the stress distribution and the flexibility of the pipe bend. The variation of bend angle and bend radius showed that it affects the maximum stress drastically and should be considered as a parameter in the flexibility and SIF factors. Moreover, the CSA results are found to be un-conservative in some cases depending on the bend angle and direction of the applied bending moment.

Evaluation of collapse moment of pressurized 30°–180° bend pipes subjected to out-of-plane bending moment

2021 ◽  
pp. 095440622110614
Author(s):  
Manish Kumar ◽  
Pronab Roy ◽  
Kallol Khan
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Plastic Material ◽  
Bending Moment ◽  
Bend Angle ◽  
Pipe Bend ◽  
Geometric Imperfection ◽  
Initial Geometric Imperfection ◽  
Out Of Plane ◽  
Plane Bending

The present paper determines collapse moments of pressurized 30°–180° pipe bends incorporated with initial geometric imperfection under out-of-plane bending moment. Extensive finite element analyses are carried out considering material as well as geometric nonlinearity. The twice-elastic-slope method is used to determine collapse moment. The results show that initial imperfection produces significant change in collapse moment for unpressurized pipe bends and pipe bends applied to higher internal pressure. The application of internal pressure produces stiffening effect to pipe bends which increases collapse moment up to a certain limit and with further increase in pressure, collapse moment decreases. The bend angle effect on collapse moment reduces with the increase in internal pressure and bend radius. Based on finite element results, collapse moment equations are formed as a function of the pipe bend geometry parameters, initial geometric imperfection, bend angle, and internal pressure for elastic-perfectly plastic material models.

Effect of Bend Angle on Gross Plastic Deformation of Pipe Bends for Out-of-Plane Bending: A Study Using Plastic Work Curvature Method

2016 ◽  
Author(s):  
Anindya Bhattacharya ◽  
Sachin Bapat ◽  
Hardik Patel ◽  
Shailan Patel ◽  
Michael P. Cross
Keyword(s):  
Plastic Deformation ◽  
Internal Pressure ◽  
Bending Moment ◽  
Plastic Work ◽  
Bend Angle ◽  
Piping System ◽  
Plastic Collapse ◽  
Pipe Bend ◽  
Out Of Plane ◽  
Plane Bending

Bends are an integral part of a piping system. Because of the ability to ovalize and warp they offer more flexibility when compared to straight pipes. Piping Code ASME B31.3 [1] provides flexibility factors and stress intensification factors for pipe bends. Like any other piping component, one of the failure mechanisms of a pipe bend is gross plastic deformation. In this paper, plastic collapse load of pipe bends have been analyzed for various bend parameters (bend parameter = tRbrm2) under internal pressure and out-of-plane bending moment for various bend angles using both small and large deformation theories. FE code ABAQUS version 6.9EF-1 has been used for the analyses. The goal of the paper is to develop an expression for plastic collapse moment for a bend using plastic work curvature method when the bend is subjected to out-of-plane bending moment and internal pressure as a function of bend angle and bend parameter.

Elastic-Plastic Analysis of an Elbow With Axial Part-Through Internal Crack at Crown Under In-Plane Bending

2008 ◽  
Author(s):  
K. M. Prabhakaran ◽  
S. R. Bhate ◽  
V. Bhasin ◽  
A. K. Ghosh
Keyword(s):  
Finite Element ◽  
Crack Depth ◽  
Bending Moment ◽  
Internal Crack ◽  
J Integral ◽  
Finite Element Analyses ◽  
Integrity Assessment ◽  
Elastic Plastic ◽  
Axial Part ◽  
Plane Bending

Piping elbows under bending moment are vulnerable to cracking at crown. The structural integrity assessment requires evaluation of J-integral. The J-integral values for elbows with axial part-through internal crack at crown under in-plane bending moment are limited in open literature. This paper presents the J-integral results of a thick and thin, 90-degree, long radius elbow subjected to in-plane opening bending moment based on number of finite element analyses covering different crack configurations. The non-linear elastic-plastic finite element analyses were performed using WARP3D software. Both geometrical and material nonlinearity were considered in the study. The geometry considered were for Rm/t = 5, and 12 with ratio of crack depth to wall thickness, a/t = 0.15, 0.25, 0.5 and 0.75 and ratio of crack length to crack depth, 2c/a = 6, 8, 10 and 12.

Effect of structural deformations and bend angle on the collapse load of pipe bends subjected to in-plane closing bending moment

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Silambarasan R. ◽  
Veerappan A.R. ◽  
Shanmugam S.
Keyword(s):  
Plastic Material ◽  
Large Strain ◽  
Bending Moment ◽  
Bend Angle ◽  
Plastic Collapse ◽  
Collapse Load ◽  
Pipe Bend ◽  
Content Type ◽  
Structural Deformations ◽  
Bend Angles

Purpose The purpose of this study is to investigate the effect of structural deformations and bend angle on plastic collapse load of pipe bends under an in-plane closing bending moment (IPCM). A large strain formulation of three-dimensional non-linear finite element analysis was performed using an elastic perfectly plastic material. A unified mathematical solution was proposed to estimate the collapse load of pipe bends subjected to IPCM for the considered range of bend characteristics. Design/methodology/approach ABAQUS was used to create one half of the pipe bend model due to its symmetry on the longitudinal axis. Structural deformations, i.e. ovality (Co) and thinning (Ct) varied from 0% to 20% in 5% steps while the bend angle (ø) varied from 30° to 180° in steps of 30°. Findings The plastic collapse load decreases as the bend angle increase for all pipe bend models. A remarkable effect on the collapse load was observed for bend angles between 30° and 120° beyond which a decline was noticed. Ovality had a significant effect on the collapse load with this effect decreasing as the bend angle increased. The combined effect of thinning and bend angle was minimal for the considered models and the maximum per cent variation in collapse load was 5.76% for small bend angles and bend radius pipe bends and less than 2% for other cases. Originality/value The effect of structural deformations and bend angle on collapse load of pipe bends exposed to IPCM has been not studied in the existing literature.

scholarly journals Effect of Ovality in Inlet Pigtail Pipe Bends Under Combined Internal Pressure and In-Plane Bending for Ni-Fe-Cr B407 Material

2017 ◽  
Vol 62 (3) ◽  
pp. 1881-1887
Author(s):  
P. Ramaswami ◽  
P. Senthil Velmurugan ◽  
R. Rajasekar
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Internal Pressure ◽  
Limit Load ◽  
Outer Radius ◽  
Factor H ◽  
Geometrical Shape ◽  
Element Analysis ◽  
Pipe Bend ◽  
Plane Bending

Abstract The present paper makes an attempt to depict the effect of ovality in the inlet pigtail pipe bend of a reformer under combined internal pressure and in-plane bending. Finite element analysis (FEA) and experiments have been used. An incoloy Ni-Fe-Cr B407 alloy material was considered for study and assumed to be elastic-perfectly plastic in behavior. The design of pipe bend is based on ASME B31.3 standard and during manufacturing process, it is challenging to avoid thickening on the inner radius and thinning on the outer radius of pipe bend. This geometrical shape imperfection is known as ovality and its effect needs investigation which is considered for the study. The finite element analysis (ANSYS-workbench) results showed that ovality affects the load carrying capacity of the pipe bend and it was varying with bend factor (h). By data fitting of finite element results, an empirical formula for the limit load of inlet pigtail pipe bend with ovality has been proposed, which is validated by experiments.

Effect of Bend Angle on Gross Plastic Deformation of Pipe Bends: A Finite Element Based Study

2015 ◽  
Author(s):  
Anindya Bhattacharya ◽  
Sachin Bapat ◽  
Hardik Patel ◽  
Shailan Patel
Keyword(s):  
Plastic Deformation ◽  
Finite Element ◽  
Failure Mechanisms ◽  
Bending Moment ◽  
Bend Angle ◽  
Piping System ◽  
Plastic Collapse ◽  
Collapse Load ◽  
Pipe Bend ◽  
Bend Angles

Bends are an integral part of a piping system. Because of the ability to ovalize and warp they offer more flexibility when compared to straight pipes. Piping Code ASME B31.3 [1] provides flexibility factors and stress intensification factors for the pipe bends. Like any other piping component, one of the failure mechanisms of a pipe bend is gross plastic deformation. In this paper, plastic collapse load of pipe bends have been analyzed for various bend parameters (bend parameter = tRbrm2) under internal pressure and in-plane bending moment for various bend angles using both small and large deformation theories. FE code ABAQUS version 6.9EF-1 has been used for the analyses.

Sign in / Sign up

Export Citation Format

Share Document