Analysis of Advanced Supercritical Carbon Dioxide Power Cycles With a Bottoming Cycle for Concentrating Solar Power Applications

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Saeb M. Besarati ◽  
D. Yogi Goswami
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Solar Power ◽  
Waste Heat ◽  
Operating Conditions ◽  
Working Fluid ◽  
Brayton Cycle ◽  
Concentrating Solar Power ◽  
Working Fluids ◽  
Supercritical Carbon

A number of studies have been performed to assess the potential of using supercritical carbon dioxide (S-CO2) in closed-loop Brayton cycles for power generation. Different configurations have been examined among which recompression and partial cooling configurations have been found very promising, especially for concentrating solar power (CSP) applications. It has been demonstrated that the S-CO2 Brayton cycle using these configurations is capable of achieving more than 50% efficiency at operating conditions that could be achieved in central receiver tower type CSP systems. Although this efficiency is high, it might be further improved by considering an appropriate bottoming cycle utilizing waste heat from the top S-CO2 Brayton cycle. The organic Rankine cycle (ORC) is one alternative proposed for this purpose; however, its performance is substantially affected by the selection of the working fluid. In this paper, a simple S-CO2 Brayton cycle, a recompression S-CO2 Brayton cycle, and a partial cooling S-CO2 Brayton cycle are first simulated and compared with the available data in the literature. Then, an ORC is added to each configuration for utilizing the waste heat. Different working fluids are examined for the bottoming cycles and the operating conditions are optimized. The combined cycle efficiencies and turbine expansion ratios are compared to find the appropriate working fluids for each configuration. It is also shown that combined recompression-ORC cycle achieves higher efficiency compared with other configurations.

Analysis of Advanced Supercritical Carbon Dioxide Power Cycles With a Bottoming Cycle for Concentrating Solar Power Applications

2013 ◽  
Author(s):  
Saeb M. Besarati ◽  
D. Yogi Goswami
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Solar Power ◽  
Waste Heat ◽  
Operating Conditions ◽  
Working Fluid ◽  
Brayton Cycle ◽  
Concentrating Solar Power ◽  
Working Fluids ◽  
Supercritical Carbon

A number of studies have been performed to assess the potential of using supercritical carbon dioxide (S-CO2) in closed-loop Brayton cycles for power generation. Different configurations have been examined among which recompression and partial cooling configurations have been found very promising, especially for concentrating solar power (CSP) applications. It has been demonstrated that the S-CO2 Brayton cycle using these configurations is capable of achieving more than 50% efficiency at operating conditions that could be achieved in central receiver tower type CSP systems. Although this efficiency is high, it might be further improved by considering an appropriate bottoming cycle utilizing waste heat from the top S-CO2 Brayton cycle. The organic Rankine cycle (ORC) is one alternative proposed for this purpose, however, its performance is substantially affected by the selection of the working fluid. In this paper, a simple S-CO2 Brayton cycle, a recompression S-CO2 Brayton cycle, and a partial cooling S-CO2 Brayton cycle are first simulated and compared with the available data in the literature. Then, an ORC is added to each configuration for utilizing the waste heat. Different working fluids are examined for the bottoming cycles and the operating conditions are optimized. The combined cycle efficiencies and turbine expansion ratios are compared to find the appropriate working fluids for each configuration. It is also shown that combined recompression-ORC cycle achieves higher efficiency compared with other configurations.

A Study of Supercritical Carbon Dioxide Power Cycle for Concentrating Solar Power Applications Using an Isothermal Compressor

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Jin Young Heo ◽  
Jinsu Kwon ◽  
Jeong Ik Lee
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Thermal Efficiency ◽  
Solar Power ◽  
Working Fluid ◽  
Brayton Cycle ◽  
Concentrating Solar Power ◽  
Power Cycle ◽  
Compressor Inlet ◽  
Supercritical Carbon

For the concentrating solar power (CSP) applications, the supercritical carbon dioxide (s-CO2) power cycle is beneficial in many aspects, including high cycle efficiencies, reduced component sizing, and potential for the dry cooling option. More research is involved in improving this technology to realize the s-CO2 cycle as a candidate to replace the conventional power conversion systems for CSP applications. In this study, an isothermal compressor, a turbomachine which undergoes the compression process at constant temperature to minimize compression work, is applied to the s-CO2 power cycle layout. To investigate the cycle performance changes of adopting the novel technology, a framework for defining the efficiency of the isothermal compressor is revised and suggested. This study demonstrates how the compression work for the isothermal compressor is reduced, up to 50%, compared to that of the conventional compressor under varying compressor inlet conditions. Furthermore, the simple recuperated and recompression Brayton cycle layouts using s-CO2 as a working fluid are evaluated for the CSP applications. Results show that for compressor inlet temperatures (CIT) near the critical point, the recompression Brayton cycle using an isothermal compressor has 0.2–1.0% point higher cycle thermal efficiency compared to its reference cycle. For higher CIT values, the recompression cycle using an isothermal compressor can perform above 50% in thermal efficiency for a wider range of CIT than the reference cycle. Adopting an isothermal compressor in the s-CO2 layout can imply larger heat exchange area for the compressor which requires further development.

Selecting the Optimum Supercritical CO2 Cycle for Indirect-Fired Applications

2019 ◽  
Author(s):  
Brittany Tom ◽  
January Smith ◽  
Aaron M. McClung
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Supercritical Co2 ◽  
Operating Conditions ◽  
Working Fluid ◽  
Performance Goals ◽  
Brayton Cycle ◽  
Power Cycle ◽  
And Performance ◽  
Supercritical Carbon

Abstract Existing research has demonstrated the viability of supercritical carbon dioxide as an efficient working fluid with numerous advantages over steam in power cycle applications. Selecting the appropriate power cycle configuration for a given application depends on expected operating conditions and performance goals. This paper presents a comparison for three indirect fired sCO2 cycles: recompression closed Brayton cycle, dual loop cascaded cycle, and partial condensation cycle. Each cycle was modeled in NPSS with an air side heater, given the same baseline assumptions and optimized over a range of conditions. Additionally, limitations on the heater system are discussed.

Effect of Mixtures on Compressor and Cooler in Supercritical Carbon Dioxide Cycles

2018 ◽  
Author(s):  
Ladislav Vesely ◽  
K. R. V. Manikantachari ◽  
Subith Vasu ◽  
Jayanta Kapat ◽  
Vaclav Dostal ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Critical Point ◽  
Carbon Capture ◽  
Power Plants ◽  
High Efficiency ◽  
Waste Heat ◽  
Operating Conditions ◽  
Working Fluid ◽  
Supercritical Carbon

With the increasing demand for electric power, the development of new power generation technologies is gaining increased attention. The supercritical carbon dioxide (S-CO2) cycle is one such technology, which has relatively high efficiency, compactness, and potentially could provide complete carbon capture. The S-CO2 cycle technology is adaptable for almost all of the existing heat sources such as solar, geothermal, fossil, nuclear power plants, and waste heat recovery systems. However, it is known that, optimal combinations of: operating conditions, equipment, working fluid, and cycle layout determine the maximum achievable efficiency of a cycle. Within an S-CO2 cycle the compression device is of critical importance as it is operating near the critical point of CO2. However, near the critical point, the thermo-physical properties of CO2 are highly sensitive to changes of pressure and temperature. Therefore, the conditions of CO2 at the compressor inlet are critical in the design of such cycles. Also, the impurity species diluted within the S-CO2 will cause deviation from an ideal S-CO2 cycle as these impurities will change the thermodynamic properties of the working fluid. Accordingly the current work examines the effects of different impurity compositions, considering binary mixtures of CO2 and: He, CO, O2, N2, H2, CH4, or H2S; on various S-CO2 cycle components. The second part of the study focuses on the calculation of the basic cycles and component efficiencies. The results of this study will provide guidance and defines the optimal composition of mixtures for compressors and coolers.

Modeling Off-Design and Part-Load Performance of Supercritical Carbon Dioxide Power Cycles

2013 ◽  
Author(s):  
John J. Dyreby ◽  
Sanford A. Klein ◽  
Gregory F. Nellis ◽  
Douglas T. Reindl
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Ambient Air ◽  
Working Fluid ◽  
Brayton Cycle ◽  
Heat Rejection ◽  
Power Cycles ◽  
Part Load ◽  
Dry Cooling ◽  
Supercritical Carbon

Continuing efforts to increase the efficiency of utility-scale electricity generation has resulted in considerable interest in Brayton cycles operating with supercritical carbon dioxide (S-CO2). One of the advantages of S-CO2 Brayton cycles, compared to the more traditional steam Rankine cycle, is that equal or greater thermal efficiencies can be realized using significantly smaller turbomachinery. Another advantage is that heat rejection is not limited by the saturation temperature of the working fluid, facilitating dry cooling of the cycle (i.e., the use of ambient air as the sole heat rejection medium). While dry cooling is especially advantageous for power generation in arid climates, the reduction in water consumption at any location is of growing interest due to likely tighter environmental regulations being enacted in the future. Daily and seasonal weather variations coupled with electric load variations means the plant will operate away from its design point the majority of the year. Models capable of predicting the off-design and part-load performance of S-CO2 power cycles are necessary for evaluating cycle configurations and turbomachinery designs. This paper presents a flexible modeling methodology capable of predicting the steady state performance of various S-CO2 cycle configurations for both design and off-design ambient conditions, including part-load plant operation. The models assume supercritical CO2 as the working fluid for both a simple recuperated Brayton cycle and a more complex recompression Brayton cycle.

Development of Turbine and Combustor for a Semi-Closed Recuperated Brayton Cycle of Supercritical Carbon Dioxide

2017 ◽  
Author(s):  
Takashi Sasaki ◽  
Masao Itoh ◽  
Hideyuki Maeda ◽  
Junichi Tominaga ◽  
Daizo Saito ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
New Technologies ◽  
Combined Cycle ◽  
Working Fluid ◽  
Brayton Cycle ◽  
The Usa ◽  
Demonstration Plant ◽  
Competitive Efficiency ◽  
Supercritical Carbon

Toshiba has been developing a turbine and a combustor for a semi-closed recuperated Brayton cycle of supercritical carbon dioxide called the Allam cycle, which is capable of both sequestrating 100% of carbon dioxide generated by combustion and providing electricity with competitive efficiency as the advanced combined cycle. The 25 MWe class demonstration plant with natural gas for this innovative cycle is being constructed in the USA by NET Power LLC and its operation is expected to be in 2017. Toshiba is going to provide the main components of its turbine and combustor. This paper describes the specification of the turbine and the combustor and consideration necessary to realize them in the first of a kind design condition of 30MPa with a supercritical carbon dioxide as its working fluid. This paper also describes some of the validation tests to realize new technologies before this turbine and combustor are installed and operated in the demonstration plant.

Off-Nominal Component Performance in a Supercritical Carbon Dioxide Brayton Cycle

2015 ◽  
Author(s):  
Eric M. Clementoni ◽  
Timothy L. Cox ◽  
Martha A. King
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Integrated System ◽  
Design System ◽  
Working Fluid ◽  
Brayton Cycle ◽  
Wide Range ◽  
Primary Driver ◽  
Atomic Power Laboratory ◽  
Supercritical Carbon

Bechtel Marine Propulsion Corporation (BMPC) is testing a supercritical carbon dioxide (S-CO2) Brayton system at the Bettis Atomic Power Laboratory. The Integrated System Test (IST) is a simple recuperated closed Brayton cycle with a variable-speed turbine-driven compressor and a constant-speed turbine-driven generator using S-CO2 as the working fluid designed to output 100 kWe. The main focus of the IST is to demonstrate operational, control, and performance characteristics of an S-CO2 Brayton power cycle over a wide range of conditions. Therefore, the IST was designed to operate in a configuration and at conditions that support demonstrating the controllability of the closed S-CO2 Brayton cycle. Operating at high system efficiency and meeting a specified efficiency target are not requirements of the IST. However, efficiency is a primary driver for many commercial applications of S-CO2 power cycles. This paper uses operational data to evaluate component off-nominal performance and predict that design system operation would be achievable.

Sign in / Sign up

Export Citation Format

Share Document