Inherent-Strain-Based Theory of Measurement of Three-Dimensional Residual Stress Distribution and Its Application to a Welded Joint in a Reactor Vessel

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Keiji Nakacho ◽  
Naoki Ogawa ◽  
Takahiro Ohta ◽  
Michisuke Nayama
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Strain Distribution ◽  
Measurement Method ◽  
Welded Joint ◽  
Three Dimensional ◽  
Reactor Vessel ◽  
Residual Stress Distribution ◽  
Stress Distributions ◽  
Inherent Strain

The stress that exists in a body under no external force is called the inherent stress. The strain that is the cause (source) of this stress is called the inherent strain. This study proposes a general theory of an inherent-strain-based measurement method for the residual stress distributions in arbitrary three-dimensional bodies and applies the method to measure the welding residual stress distribution of a welded joint in a reactor vessel. The inherent-strain-based method is based on the inherent strain and the finite element method. It uses part of the released strains and solves an inverse problem by a least squares method. Thus, the method gives the most probable value and deviation of the residual stress. First, the basic theory is explained in detail, and then a concrete measurement method for a welded joint in a reactor vessel is developed. In the method, the inherent strains are unknowns. In this study, the inherent strain distribution was expressed with an appropriate function, significantly decreasing the number of unknowns. Five types of inherent strain distribution functions were applied to estimate the residual stress distribution of the joint. The applicability of each function was evaluated. The accuracy and reliability of the analyzed results were assessed in terms of the residuals, the unbiased estimate of the error variance, and the welding mechanics. The most suitable function, which yields the most reliable result, was identified. The most reliable residual stress distributions of the joint are shown, indicating the characteristics of distributions with especially large tensile stress that may produce a crack.

Influence of the Welded Joint on the Mechanical Behavior of Steel Piles during Static and Dynamic Deformation

2007 ◽  
Vol 345-346 ◽  
pp. 1469-1472
Author(s):  
Gab Chul Jang ◽  
Kyong Ho Chang ◽  
Chin Hyung Lee
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Mechanical Behavior ◽  
Welded Joint ◽  
Dynamic Deformation ◽  
Three Dimensional ◽  
Steel Structures ◽  
Residual Stress Distribution ◽  
Dynamic Mechanical Behavior ◽  
Steel Piles

During manufacturing the welded joint of steel structures, residual stress is produced and weld metal is used inevitably. And residual stress and weld metal influence on the static and dynamic mechanical behavior of steel structures. Therefore, to predict the mechanical behavior of steel pile with a welded joint during static and dynamic deformation, the research on the influence of the welded joints on the static and dynamic behavior of steel pile is clarified. In this paper, the residual stress distribution in a welded joint of steel piles was investigated by using three-dimensional welding analysis. The static and dynamic mechanical behavior of steel piles with a welded joint is investigated by three-dimensional elastic-plastic finite element analysis using a proposed dynamic hysteresis model. Numerical analyses of the steel pile with a welded joint were compared to that without a welded joint with respect to load carrying capacity and residual stress distribution. The influence of the welded joint on the mechanical behavior of steel piles during static and dynamic deformation was clarified by comparing analytical results

Residual Stress Evaluation of Dissimilar Weld Joint Using Reactor Vessel Outlet Nozzle Mock-Up Model (Report-1)

2008 ◽  
Author(s):  
Itaru Muroya ◽  
Youichi Iwamoto ◽  
Naoki Ogawa ◽  
Kiminobu Hojo ◽  
Kazuo Ogawa
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Welding Process ◽  
Reactor Vessel ◽  
Residual Stress Distribution ◽  
Test Model ◽  
Alloy 600 ◽  
Outlet Nozzle ◽  
Stress Evaluation ◽  
Weld Region

In recent years, the occurrence of primary water stress corrosion cracking (PWSCC) in Alloy 600 weld regions of PWR plants has increased. In order to evaluate the crack propagation of PWSCC, it is required to estimate stress distribution including residual stress and operational stress through the wall thickness of the Alloy 600 weld region. In a national project in Japan for the purpose of establishing residual stress evaluation method, two test models were produced based on a reactor vessel outlet nozzle of Japanese PWR plants. One (Test model A) was produced using the same welding process applied in Japanese PWR plants in order to measure residual stress distribution of the Alloy 132 weld region. The other (Test model B) was produced using the same fabrication process in Japanese PWR plants in order to measure stress distribution change of the Alloy 132 weld region during fabrication process such as a hydrostatic test, welding a main coolant pipe to the stainless steel safe end. For Test model A, residual stress distribution was obtained using FE analysis, and was compared with the measured stress distribution. By comparing results, it was confirmed that the FE analysis result was in good agreement with the measurement result. For mock up test model B, the stress distribution of selected fabrication processes were measured using the Deep Hole Drilling (DHD) method. From these measurement results, it was found that the stress distribution in thickness direction at the center of the Alloy 132 weld line was changed largely during welding process of the safe end to the main coolant pipe.

Residual Stress Distribution of Ceramic-Metal Joint

1989 ◽  
Vol 33 ◽  
pp. 353-362 ◽  
Author(s):  
Masanori Kurita ◽  
Makoto Sato ◽  
Ikuo Ihara ◽  
Akira Saito
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Stress Analysis ◽  
Three Dimensional ◽  
Axial Direction ◽  
Residual Stress Distribution ◽  
X Ray Diffraction ◽  
Copper Sheet ◽  
Brittle Behavior ◽  
Curve Method

AbstractCeramics are sometimes bonded to ductile metals in order to make up for their brittle behavior for industrial use. The residual stress will be induced in ceramics bonded to metals at high temeprature, and it has a strong influence on the strength of ceramic-metal joints. A silicon nitride plate was bonded to a carbon steel plate by brazing to a copper sheet sandwiched between the two materials. The residual stress distribution of the joint specimen was determined by x-ray diffraction using the Gaussian curve method. The measured residual stress distribution almost agreed with that calculated by the three-dimensional thermoelastoplastic stress analysis using FEM, but differed remarkably from that calculated by the two-dimensional stress analysis. This is because a stress concentration occurs at the ceramic-metal interface and the stress distributes three - dimensionally. The stress σx in the axial direction on the surface of the specimen takes maximum values at the center and the edge of the interface.

Effect of Welding Sequence on the Residual Stress Distribution in a Stiffened Plate

2016 ◽  
Author(s):  
Bai-Qiao Chen ◽  
C. Guedes Soares
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Lower Layer ◽  
Plate Thickness ◽  
Three Dimensional ◽  
Welding Process ◽  
Residual Stress Distribution ◽  
Steel Plates ◽  
Tension Zone ◽  
Welding Sequence

This work investigates the temperature distribution, deformation and residual stress in steel plates as a result of different sequences of welding. The single-pass gas tungsten arc welding process is simulated by a three dimensional nonlinear thermo-elasto-plastic approach. It is observed that the distribution of residual stress varies through the direction of plate thickness. It is concluded that the welding sequence affects not only the welding deformation but also the residual stress mainly in the lower layer of the plates. An in-depth discussion on the pattern of residual stress distribution is presented, especially on the width of the tension zone. Smaller residual tension zone and slightly lower compressive stress are found in thicker plate.

Important Residual Stress Features in Reactor Nozzle Dissimilar Metal Welds

2011 ◽  
Author(s):  
Jinmiao Zhang ◽  
Shaopin Song ◽  
Pingsha Dong
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Nuclear Reactor ◽  
Residual Stress Distribution ◽  
Stress Distributions ◽  
Weld Overlay ◽  
Dissimilar Metal ◽  
Nozzle Length ◽  
Dissimilar Metal Weld ◽  
Metal Weld

This paper is focused on the study of residual stress distribution at a dissimilar metal weld (DMW) of nuclear reactor nozzle. The paper extends some of the recent research on this subject by investigating the effect of weld sequence and nozzle length design on the residual stress distributions. It also investigates the effect of a partial excavation repair and a weld overlay on the residual stress distribution. As a result, some of the important residual stress features at DMW are revealed and these features are discussed and summarized in the paper.

Measurement of Through-Thickness Residual Stress in Primary Piping of Girth Welded Joint

2008 ◽  
Vol 580-582 ◽  
pp. 577-580
Author(s):  
Masahito Mochizuki ◽  
Shigetaka Okano ◽  
Gyu Baek An ◽  
Masao Toyoda
Keyword(s):  
Residual Stress ◽  
Direct Measurement ◽  
Welded Joint ◽  
Strain Analysis ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Thickness Direction ◽  
Welded Pipe ◽  
Inherent Strain ◽  
Pipe Joint

The welding residual stress of a butt-welded pipe joint is evaluated, using inherent strain analysis. The residual stress distribution is obtained in detail along the thickness direction. The residual stresses are similar to values obtained by direct measurement on the specimen surface; as if though direct measurement is not used for the inherent strain analysis. These results indicate that inherent strain analysis is effective in evaluating through-thickness residual stress in primary piping of girth welded joint.

Sign in / Sign up

Export Citation Format

Share Document