Roles of Nanofluids, Temperature of Base Fluids, and Pressure Gradient on Heat Transfer Enhancement From a Cylinder: Uniformly Heated/Heat Flux

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Dilip K. Maiti ◽  
Swati Sharma
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Gradient ◽  
Heat Transfer Enhancement ◽  
Thermal Conditions ◽  
Constant Heat Flux ◽  
Inlet Temperature ◽  
Water Mixture ◽  
Transfer Enhancement ◽  
Different Temperatures

Heat transfer from a cylinder of square cross section (either dissipating constant heat flux (qW) or maintaining at a constant temperature (TW)) placed near a plane wall under the incidence of nonuniform linear/nonlinear velocity profile is studied numerically (finite volume method (FVM), quadratic upstream interpolation for convective kinematics (QUICK), and SIMPLE). The conventional fluids are chosen as water, and ethylene glycol–water mixture. The nanoparticles are selected as Al2O3 and CuO. Roles of pressure gradient P (at the inlet), temperature of base fluids, thermal conditions (TW or qW), and nanofluids' parameters (nanoparticle concentrations (ϕ), diameter, materials, and base fluids) on the heat transfer (Nusselt number (Nu¯M)) of the cylinder are investigated here. Nu¯M enhancement from the cylinder together with its drag coefficient reduction/increment due to addition of nanomaterials in both fluids at two different temperatures is assessed under the Couette flow. Classical fluid dynamics relationship among Nu¯M, Reynolds number (Re), and Prandtl number is discussed through Colburn j–factor, and hence the utility of proposed correlation between j–factor and Re toward engineering problems is also explored. The graphical observations of dependency of Nu¯M on the aforesaid parameters are reconfirmed by proposed functional forms of Nu¯M=Nu¯M(P), Nu¯M=Nu¯M(ϕ) and hence Nu¯M=Nu¯M(P,ϕ). An effort is made to examine the effectiveness of the aforementioned parameters on the heat transfer enhancement rate.

scholarly journals Experimental Investigation of Heat Transfer Enhancement by Pulsating Flow in a Minichannel

2021 ◽  
Vol 2116 (1) ◽  
pp. 012031
Author(s):  
P Kumavat ◽  
S M O’Shaughnessy
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Enhancement ◽  
Flow Rate ◽  
Wall Temperature ◽  
High Performance ◽  
Amplitude Ratio ◽  
Constant Heat Flux ◽  
Pulsating Flow ◽  
Transfer Enhancement

Abstract The increasing power density requirements of next generation high performance electronic devices has resulted in ever-increasing heat flux densities which necessitates the evolution of new liquid-based heat exchange technologies. Pulsating flow in single-phase cooling systems is viewed as a potential solution. In this study, an experimental analysis of thermally developed pulsating flow in a rectangular minichannel is conducted. The channel test setup involves a heated bottom section approximated as a constant heat flux boundary. Asymmetric sinusoidal pulsating flows with a fixed flow rate amplitude ratio of 0.9 and Womersley numbers (Wo) of 0.51 and 1.6 are investigated. The wall temperature profiles are recorded using infrared thermography. It is observed that the transverse wall temperature profile is influenced by the sudden velocity variations of such characteristic waveforms. A heat transfer enhancement of 6% was determined for asymmetric flow pulsations of Wo > 1 over the steady flow with a potential augmentation for higher flow rate amplitudes.

scholarly journals Heat transfer enhancement of car radiator using aqua based magnesium oxide nanofluids

2015 ◽  
Vol 19 (6) ◽  
pp. 2039-2048 ◽  
Author(s):  
Hafiz Ali ◽  
Muhammad Azhar ◽  
Musab Saleem ◽  
Qazi Saeed ◽  
Ahmed Saieed
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Management ◽  
Heat Transfer Performance ◽  
Inlet Temperature ◽  
Fluid Temperature ◽  
Transfer Enhancement ◽  
Volumetric Concentration ◽  
Flow Rates ◽  
Transfer Rates

The focus of this research paper is on the application of water based MgO nanofluids for thermal management of a car radiator. Nanofluids of different volumetric concentrations (i.e. 0.06%, 0.09% and 0.12%) were prepared and then experimentally tested for their heat transfer performance in a car radiator. All concentrations showed enhancement in heat transfer compared to the pure base fluid. A peak heat transfer enhancement of 31% was obtained at 0.12 % volumetric concentration of MgO in basefluid. The fluid flow rate was kept in a range of 8-16 liter per minute. Lower flow rates resulted in greater heat transfer rates as compared to heat transfer rates at higher flow rates for the same volumetric concentration. Heat transfer rates were found weakly dependent on the inlet fluid temperature. An increase of 8?C in inlet temperature showed only a 6% increase in heat transfer rate.

scholarly journals Heat transfer enhancement during condensation of water steam on inclined pipe

2021 ◽  
Vol 2039 (1) ◽  
pp. 012031
Author(s):  
S Z Sapozhnikov ◽  
V Yu Mityakov ◽  
A V Mityakov ◽  
A Yu Babich ◽  
E R Zainullina
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Enhancement ◽  
Unit Area ◽  
Experimental Results ◽  
Transfer Enhancement ◽  
Water Steam ◽  
Saturated Water ◽  
Informative Content ◽  
Inclined Pipe

Abstract This paper presents experimental study of heat transfer during film condensation of saturated water steam on the outer surface of the inclined pipe by gradient heatmetry. Heat flux per unit area was measured by gradient heat flux sensors made of a single-crystal bismuth. The experimental results are presented in the graphs of heat flux per unit area dependence on time and azimuthal angle. The highest average heat transfer coefficient during condensation of α = 6.94 kW/(m2 • K) was observed when the pipe was inclined at the angle of ψ = 20 °. This value exceeds one obtained on a vertical pipe by 14.9 %. Heat transfer enhancement during condensation of saturated water steam on inclined pipe is associated with changes in condensate film flow. Another part of experiments was made by simultaneously using of gradient heatmetry and condensate flow visualization. Experimental results confirmed the applicability and high informative content of proposed comprehensive method. Comprehensive study of heat transfer during condensation confirmed that heat flux per unit area pulsations may be explained by the formation of individual drops, their coalescence, and drainage from the sensor surface.

Falling Film Evaporation of Water on Horizontal Configured Tube Bundles

2010 ◽  
Author(s):  
Wei Li ◽  
Xiaoyu Wu ◽  
Zhong Luo
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Enhancement ◽  
Inlet Temperature ◽  
Falling Film ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Film Evaporation ◽  
Tube Bundles ◽  
Falling Film Evaporation

This paper reports an experimental study on falling film evaporation of water on 6-row horizontal configured tube bundles in a vacuum. Three types of configured tubes, Turbo-CAB-19fpi and −26fpi, Korodense, including smooth tubes for reference, were tested in a range of film Reynolds number from about 10 to 110. Results show that as the falling film Reynolds number increases, falling film evaporation goes from tubes partial dryout regime to fully wet regime; the mean heat transfer coefficients reach peak values in the transition point. Turbo-CAB tubes have the best heat transfer enhancement of falling film evaporation in both regimes, but Korodense tubes’ overall performances are better when tubes are fully wet. The inlet temperature of heating water has hardly any effects on the heat transfer, but the evaporation pressure has controversial effects. A correlation with errors within 10% was also developed to predict the heat transfer enhancement capacity.

Sign in / Sign up

Export Citation Format

Share Document