Experimental Performance Evaluation of Humidification–Dehumidification System With Direct-Contact Dehumidifier

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Saeed Dehghani ◽  
Farzaneh Mahmoudi ◽  
Abhijit Date ◽  
Aliakbar Akbarzadeh

Abstract Humidification–dehumidification (HDH) desalination with direct contact dehumidifier system is designed and fabricated. Experimental tests are performed under various operating conditions in order to explore the influence of temperatures and mass flow rates of seawater and freshwater on system performance by utilizing non-dimensional parameters. It is shown that, for any case, there is an optimum flow rate ratio of water to air, which results in a maximum water production rate. A mathematical model is utilized to evaluate the system performance and compare the outcomes with the experimental results. In addition, the effect of feed water salinity from 0–30% on the water production rate is experimentally investigated. The results showed that the maximum achieved recovery ratio of the proposed HDH system is 5% under the working condition of seawater temperature at 73 °C with 3% salinity and cold freshwater at 28 °C. Furthermore, the system was able to produce water at nearly saturated seawater feed.

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Guangfu Cao ◽  
Qingfen Ma ◽  
Jingru Li ◽  
Shenghui Wang ◽  
Chengpeng Wang ◽  
...  

A Bubbling and Vacuum-enhanced direct contact membrane distillation (BVDCMD) is proposed to improve the water production rate of the direct contact membrane distillation (DCMD-)based seawater desalination process. Its heat and mass transfer mechanism are theoretically analyzed, and a CFD model is established, which is verified by the published data. Four types of the noncondensable gas, “O2,” “air,” “N2,” and “H2,” are adopted as the bubbling gas, and their process enhancements under different pressure of permeate side, temperature, and NaCl concentration of feed side and flow velocities are investigated. The results show that the permeate flux increased remarkably with the decrease in the viscosity of the bubbling gas, and hence, “H2” is the best option for the bubbling gas, with the permeate flux being enhanced by 144.11% and the effective heat consumption being increased by 20.81% on average. The effective water production rate of BVDCMD is predicted to be 42.38% more than that of DCMD, proving its feasibility in the seawater desalination.


2020 ◽  
Author(s):  
Youssef Moulane ◽  
Emmanuel Jehin ◽  
Francisco José Pozuelos ◽  
Jean Manfroid ◽  
Zouhair Benkhaldoun ◽  
...  

<p>Long Period Comets (LPCs) have orbital periods longer than 200 years, perturbed from their resting place in the Oort cloud. Such gravitational influences may send these icy bodies on a path towards the center of the Solar system in highly elliptical orbits. In this work, we present the activity and composition evolution of several LPCs observed with both TRAPPIST telescopes (TS and TN) during the period of 2019-2020. These comets include: C/2017 T2 (PANSTARRS), C/2018 Y1 (Iwamoto), C/2018 W2 (Africano), and disintegrated comet C/2019 Y4 (ATLAS). We monitored the OH, NH, CN, C<sub>2</sub> and C<sub>3</sub> production rates evolution and their chemical mixing ratios with respect to their distances to the Sun as well as the dust production rate proxy (A(0)fp) during the journey of these comets into the inner Solar system.</p> <p><strong>C/2017 T2 (PANSTARRS)</strong> is a very bright comet which was discovered on October 2, 2017 when it was 9.20 au from the Sun. We started observing this comet with TS at the beginning of August 2019 when it was at 3.70 au. The comet made the closest approach to the Earth on December 28, 2019 at a distance of 1.52 au and it passed the perihelion on May 4, 2020 at 1.61 au. The water production rate of the comet reached a maximum of (4,27±0,12)10<sup>28 </sup>molecules/s and its dust production rate (A(0)fp(RC)) also reached the peak of 5110±25 cm on January 26, 2020, when the comet was at 2.08 au from the Sun (-100 days pre-perihelion). At the time of writing, we still monitoring the activity of the comet with TN at heliocentric distance of 1.70 au. Our observations show that C/2017 T2 is a normal LPC.</p> <p><strong>C/2018 Y1 (Iwamoto)</strong> is a nearly parabolic comet with a retrograde orbit discovered on December 18, 2018 by Japanese amateur astronomer Masayuki Iwamoto. We monitored the activity and composition of Iwamoto with both TN and TS telescopes from January to March 2019. The comet reached its maximum activity on January 29, 2019 when it was at 1.29 au from the Sun (-8 days pre-perihelion) with Q(H<sub>2</sub>O)=(1,68±0,05)10<sup>28 </sup>molecules/s and A(0)fp(RC)= 92±5 cm. These measurements show that it was a dust-poor comet compared to the typical LPCs.</p> <p><strong>C/2018 W2 (Africano) </strong>was discovered on November 27, 2018 at Mount Lemmon Survey with a visual magnitude of 20. The comet reached its perihelion on September 6, 2019 when it was at 1.45 au from the Sun. We monitored the comet from July 2019 (r<sub>h</sub>=1.71 au) to January 2020 (r<sub>h</sub>=2.18 au) with both TN and TS telescopes. The comet reached its maximum activity on September 21, 15 days post-perihelion (r<sub>h</sub>=1.47 au) with Q(H<sub>2</sub>O)=(0,40±0,03)10<sup>28 </sup>molecules/s.</p> <p><strong>C/2019 Y4 (ATLAS)</strong> is a comet with a nearly parabolic orbit discovered on December 18, 2019 by the ATLAS survey. We started to follow its activity and composition with broad- and narrow-band filters with the TN telescope on February 22, 2019 when it was at 1.32 au from the Sun until May 3, 2020 when the comet was at a heliocentric distance of 0.90 au inbound. The comet activity reached a maximum on March 22 (r<sub>h</sub>=1.65 au) 70 days before perihelion. At that time, the water-production rate reached (1,53±0,04)10<sup>28 </sup>molecules/s and the A(0)fp reached (1096±14) cm in the red filter. After that, the comet began to fade and disintegrated into several fragments.</p>


Author(s):  
Danielle Park ◽  
Elnaz Norouzi ◽  
Chanwoo Park

A small-scale Direct Contact Membrane Distillation (DCMD) system was built to investigate its water distillation performance for varying inlet temperatures and flow rates of feed and permeate streams, and salinity. A counterflow configuration between the feed and permeate streams was used to achieve an efficient heat exchange. A two-dimensional Computational Fluid Dynamics (CFD) model was developed and validated using the experimental results. The numerical results were compared with the experiments and found to be in good agreement. From this study, the most desirable conditions for distilled water production were found to be a higher feed water temperature, lower permeate temperature, higher flow rate and less salinity. The feed water temperature had a greater impact on the water production than the permeate water temperature. The numerical simulation showed that the water mass flux was maximum at the inlet of the feed stream where the feed temperature was the highest and rapidly decreased as the feed temperature decreased.


2011 ◽  
Vol 63 (7) ◽  
pp. 1349-1356 ◽  
Author(s):  
C. Michon ◽  
M.-N. Pons ◽  
P. Bauda ◽  
H. Poirot ◽  
O. Potier

Rivers used for drinking water production might be subject to anthropogenic pollution discharge upstream of the intake point. This problem was investigated in the case of the Moselle River, used for water production in Nancy (350,000 inhabitants) and which might be impacted by industrial activities 60 km upstream. The arsenic flux of a pulp and paper mill discharging in the Moselle River at this location has been more specifically investigated. The main sources of arsenic in that mill seemed to be the recovered papers and the gravel pit water used as feed water. The arsenic input related to wood and bark was limited. The main arsenic outputs from the plant were the paper produced on site and the deinking sludge. The arsenic concentration in the effluent of the wastewater treatment plant (WWTP) was not correlated to the one in the gravel pit water, but may depend on the operating conditions of the WWTP or the changes in processes of the mill. The impact of this anthropogenic source of arsenic on the Moselle River was slightly larger in summer, when the flowrate was lower. Globally the impact of the paper mill on the Moselle River water quality was limited in terms of arsenic.


2020 ◽  
Vol 8 (41) ◽  
pp. 21771-21779
Author(s):  
Jiaxiang Ma ◽  
Yu Han ◽  
Ying Xu ◽  
Tao Zhang ◽  
Jingjing Zhang ◽  
...  

An integrated photo-electro-thermal evaporation system uses a simple preparation process successfully achieves the improvement of water production rate in the day and continuous water evaporation at night.


Icarus ◽  
2013 ◽  
Vol 225 (1) ◽  
pp. 740-748 ◽  
Author(s):  
M.R. Combi ◽  
J.T.T. Mäkinen ◽  
J.-L. Bertaux ◽  
E. Quémerais ◽  
S. Ferron ◽  
...  

2004 ◽  
Vol 126 (3) ◽  
pp. 219-225 ◽  
Author(s):  
James F. Klausner ◽  
Yi Li ◽  
Mohamed Darwish ◽  
Renwei Mei

An innovative diffusion driven desalination (DDD) process is presented, and its performance based on thermodynamic considerations is thoroughly explored. The desalination is driven by water vapor saturating low humidity air flowing through a diffusion tower. Liquid water is condensed out of the air/vapor mixture in a direct contact condenser. The desalination process is suitable for operation at low temperatures and may be driven by waste heat with low exergy. It is demonstrated that the DDD process can yield a fresh water production efficiency of 4.5% with thermal energy consumption of 0.56 kWh per kilogram of fresh water production based on a feed water temperature of only 50°C. An example is discussed in which the DDD process utilizes waste heat from a 100 MW steam power plant to produce 1.51 million gallons of fresh water per day.


Sign in / Sign up

Export Citation Format

Share Document