Three-Dimensional Turbulent Flow of the Tip Leakage Vortex in an Axial Compressor Rotor Passage

2000 ◽  
Author(s):  
Hongwei Ma ◽  
Haokang Jiang
Keyword(s):  
Turbulent Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Radial Component ◽  
Reynolds Stresses ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor

Three-dimensional turbulent flow of the tip leakage vortex in a single-stage axial compressor rotor passage is studied using a 3-Component Laser Doppler Velocimetry. The measurement results indicate that the tip leakage vortex originates at about 10% axial chord, 8% pitch away from the suction surface, and becomes strongest at about 30% chord. With the flow downstream, the vortex core moves toward the pressure surface and to a lower radial location, leading to substantial flow mixing, blockage and turbulence in the tip region. The radial component of turbulence intensities is found to be the highest while the axial-radial component of Reynolds stresses is the largest. Breakdown of the leakage vortex occurs inside the rear rotor passage, which makes the flow more turbulent in a wider region downstream. This viewpoint is confirmed by the measurements of unsteady static pressure on the casing wall. Breakdown of a leakage vortex is observed clearly in a compressor cascade with a small clearance. Unsteady interactions of the broken vorticities and the suction surface’s boundary layer are shown obviously inside the downstream passage.

Unsteady Flow Behavior due to Breakdown of Tip Leakage Vortex in an Axial Compressor Rotor at Near-Stall Condition

2000 ◽  
Author(s):  
Masato Furukawa ◽  
Kazuhisa Saiki ◽  
Kazutoyo Yamada ◽  
Masahiro Inoue
Keyword(s):  
Unsteady Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Surface Boundary ◽  
Pressure Side ◽  
Suction Surface ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Pressure Surface ◽  
Compressor Rotor

The unsteady flow nature caused by the breakdown of the tip leakage vortex in an axial compressor rotor at near-stall conditions has been investigated by unsteady three-dimensional Navier-Stokes flow simulations. The simulations show that the spiral-type breakdown of the tip leakage vortex occurs inside the rotor passage at the near-stall conditions. Downstream of the breakdown onset, the tip leakage vortex twists and turns violently with time, thus interacting with the pressure surface of the adjacent blade. The motion of the vortex and its interaction with the pressure surface are cyclic. The vortex breakdown causes significant changes in the nature of the tip leakage vortex, which result in the anomalous phenomena in the time-averaged flow fields near the tip at the near-stall conditions: no rolling-up of the leakage vortex downstream of the rotor, disappearance of the casing wall pressure trough corresponding to the leakage vortex, large spread of the low-energy fluid accumulating on the pressure side, and large pressure fluctuation on the pressure side. As the flow rate is decreased, the movement of the tip leakage vortex due to its breakdown becomes so large that the leakage vortex interacts with the suction surface as well as the pressure one. The interaction with the suction surface gives rise to the three-dimensional separation of the suction surface boundary layer.

Three-Dimensional Turbulent Flow in the Tip Region of an Axial Compressor Rotor Passage at a Near Stall Condition

2001 ◽  
Author(s):  
Hongwei Ma ◽  
Haokang Jiang
Keyword(s):  
Turbulent Flow ◽  
Large Scale ◽  
Three Dimensional ◽  
Axial Flow ◽  
Leading Edge ◽  
Rotating Stall ◽  
Suction Surface ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor

This paper presents an experimental study of the three-dimensional turbulent flow field in the tip region of an axial flow compressor rotor passage at a near stall condition. The investigation was conducted in a low-speed large-scale compressor using a 3-component Laser Doppler Velocimetry and a high frequency pressure transducer. The measurement results indicate that a tip leakage vortex is produced very close to the leading edge, and becomes the strongest at about 10% axial chord from the leading edge. Breakdown of the vortex periodically occurs at about 1/3 chord, causing very strong turbulence in the radial direction. Flow separation happens on the tip suction surface at about half chord, prompting the corner vortex migrating toward the pressure side. Tangential migration of the low-energy fluids results in substantial flow blockage and turbulence in the rear of a rotor passage. Unsteady interactions among the tip leakage vortex, the separated vortex and the corner flow should contribute to the inception of the rotating stall in a compressor.

Unsteady Three-Dimensional Flow Phenomena Due to Breakdown of Tip Leakage Vortex in a Transonic Axial Compressor Rotor

2004 ◽  
Author(s):  
K. Yamada ◽  
M. Furukawa ◽  
T. Nakano ◽  
M. Inoue ◽  
K. Funazaki
Keyword(s):  
Shock Wave ◽  
Flow Field ◽  
Vortex Breakdown ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor

Unsteady three-dimensional flow fields in a transonic axial compressor rotor (NASA Rotor 37) have been investigated by unsteady Reynolds-averaged Navier-Stokes simulations. The simulations show that the breakdown of the tip leakage vortex occurs in the compressor rotor because of the interaction of the vortex with the shock wave. At near-peak efficiency condition small bubble-type breakdown of the tip leakage vortex happens periodically and causes the loading of the adjacent blade to fluctuate periodically near the leading edge. Since the blade loading near the leading edge is closely linked to the swirl intensity of the tip leakage vortex, the periodic fluctuation of the blade loading leads to the periodic breakdown of the tip leakage vortex, resulting in self-sustained flow oscillation in the tip leakage flow field. However, the tip leakage vortex breakdown is so weak and small that it is not observed in the time-averaged flow field at near-peak efficiency condition. On the other hand, spiral-type breakdown of the tip leakage vortex is caused by the interaction between the vortex and the shock wave at near-stall operating condition. The vortex breakdown is found continuously since the swirl intensity of tip leakage vortex keeps strong at near-stall condition. The spiral-type vortex breakdown has the nature of self-sustained flow oscillation and gives rise to the large fluctuation of the tip leakage flow field, in terms of shock wave location, blockage near the rotor tip and three-dimensional separation structure on the suction surface. It is found that the breakdown of the tip leakage vortex leads to the unsteady flow phenomena near the rotor tip, accompanying large blockage effect in the transonic compressor rotor at the near-stall condition.

Experimental Study on the Three-Dimensional Flow Within a Compressor Cascade With Tip Clearance: Part II—The Tip Leakage Vortex

1993 ◽  
Vol 115 (3) ◽  
pp. 444-450 ◽  
Author(s):  
S. Kang ◽  
C. Hirsch
Keyword(s):  
Vortex Core ◽  
Three Dimensional ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Vortex ◽  
Vortex Center ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Tip Leakage Vortex ◽  
Tip Leakage

An analysis of the experimental data of a linear compressor cascade with tip clearance is presented with special attention to the development of the tip leakage vortex. A method for determining the tip vortex core size, center position, and vorticity or circulation from the measured data is proposed, based on the assumption of a circular tip vortex core. It is observed that the axial velocity profile passing through the tip vortex center is wavelike. The vorticity of the tip vortex increases rapidly near the leading edge and reaches its highest values at a short distance downstream, from which it gradually decreases. In the whole evolution, its size is growing and its center is moving away from both the suction surface and the endwall, approximately in a linear way.

Three-Dimensional Turbulent Flow Field Downstream of a Single-Stage Axial Compressor Rotor

2000 ◽  
Author(s):  
Hongwei Ma ◽  
Haokang Jiang
Keyword(s):  
Flow Field ◽  
Turbulent Flow ◽  
Mass Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Single Stage ◽  
Suction Surface ◽  
Trailing Edge ◽  
Rotor Wake ◽  
Compressor Rotor

This paper reports an experimental investigation of the three-dimensional turbulent flow downstream of a single-stage axial compressor rotor. The flow fields were measured at two axial locations in the rotor-stator gap at different mass-flow conditions. Both hot-wire probe and fast-response pressure probe were employed to survey the flow structure. At the design condition, substantial flow blockage, turbulence, loss and aerodynamic noise mainly occur in the tip mid-passage, the rotor wake and at the hub corner of the suction surface. The radial component is the highest of the three turbulence intensities at 15% axial chord downstream of the trailing edge. With the flow downstream, the radial turbulence components decay fast. Interactions of the tip leakage vorticities and the rotor wake are found at 30% axial chord downstream of the trailing edge. With the mass-flow decrease, the turbulence intensities and shear stresses become stronger, while the radial components increase fast. The flow separation and tangential migration of the low-energy fluids at the tip corner of the suction surface play an important role in the tip flow field at a low mass-flow condition.

scholarly journals Experimental Study on the Three Dimensional Flow Within a Compressor Cascade With Tip Clearance: Part II — The Tip Leakage Vortex

1992 ◽  
Author(s):  
Shun Kang ◽  
Ch. Hirsch
Keyword(s):  
Vortex Core ◽  
Three Dimensional ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Vortex ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Vortex Centre

An analysis of the experimental data of a linear compressor cascade with tip clearance is presented with special attention to the development of the tip leakage vortex. A method for determining the tip vortex core size, centre position and vorticity or circulation from the measured data is proposed, based on the assumption of a circular tip vortex core. It is observed that the axial velocity profile passing through the tip vortex centre is wake-like. The vorticity of the tip vortex increases rapidly near the leading edge and reaches its highest values at a short distance downstream, from which it gradually decreases. In the whole evolution, its size is growing and its centre is moving away from both the suction surface and the endwall, approximately in a linear way.

Study of the Standard k-ε Model for Tip Leakage Flow in an Axial Compressor Rotor

2016 ◽  
Vol 33 (4) ◽  
Author(s):  
Yanfei Gao ◽  
Yangwei Liu ◽  
Luyang Zhong ◽  
Jiexuan Hou ◽  
Lipeng Lu
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Turbulent Viscosity ◽  
Axial Compressor ◽  
Leakage Flow ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Compressor Rotor

AbstractThe standard k-ε model (SKE) and the Reynolds stress model (RSM) are employed to predict the tip leakage flow (TLF) in a low-speed large-scale axial compressor rotor. Then, a new research method is adopted to “freeze” the turbulent kinetic energy and dissipation rate of the flow field derived from the RSM, and obtain the turbulent viscosity using the Boussinesq hypothesis. The Reynolds stresses and mean flow field computed on the basis of the frozen viscosity are compared with the results of the SKE and the RSM. The flow field in the tip region based on the frozen viscosity is more similar to the results of the RSM than those of the SKE, although certain differences can be observed. This finding indicates that the non-equilibrium turbulence transport nature plays an important role in predicting the TLF, as well as the turbulence anisotropy.

Flow Field Unsteadiness in the Tip Region of a Transonic Compressor Rotor

1997 ◽  
Vol 119 (1) ◽  
pp. 122-128 ◽  
Author(s):  
S. L. Puterbaugh ◽  
W. W. Copenhaver
Keyword(s):  
Flow Field ◽  
High Performance ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Vortex Interaction ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Operating Points

An experimental investigation concerning tip flow field unsteadiness was performed for a high-performance, state-of-the-art transonic compressor rotor. Casing-mounted high frequency response pressure transducers were used to indicate both the ensemble averaged and time varying flow structure present in the tip region of the rotor at four different operating points at design speed. The ensemble averaged information revealed the shock structure as it evolved from a dual shock system at open throttle to an attached shock at peak efficiency to a detached orientation at near stall. Steady three-dimensional Navier Stokes analysis reveals the dominant flow structures in the tip region in support of the ensemble averaged measurements. A tip leakage vortex is evident at all operating points as regions of low static pressure and appears in the same location as the vortex found in the numerical solution. An unsteadiness parameter was calculated to quantify the unsteadiness in the tip cascade plane. In general, regions of peak unsteadiness appear near shocks and in the area interpreted as the shock-tip leakage vortex interaction. Local peaks of unsteadiness appear in mid-passage downstream of the shock-vortex interaction. Flow field features not evident in the ensemble averaged data are examined via a Navier-Stokes solution obtained at the near stall operating point.

Education Committee Best Paper of 1995 Award: Methods of Classical Mechanics Applied to Turbulence Stresses in a Tip Leakage Vortex

1996 ◽  
Vol 118 (4) ◽  
pp. 622-629 ◽  
Author(s):  
J. G. Moore ◽  
S. A. Schorn ◽  
J. Moore
Keyword(s):  
Stress Tensor ◽  
Reynolds Stress ◽  
Classical Mechanics ◽  
Three Dimensional ◽  
Surface Model ◽  
Reynolds Stresses ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Stress Tensors ◽  
Principal Directions

Moore et al. measured the six Reynolds stresses in a tip leakage vortex in a linear turbine cascade. Stress tensor analysis, as used in classical mechanics, has been applied to the measured turbulence stress tensors. Principal directions and principal normal stresses are found. A solid surface model, or three-dimensional glyph, for the Reynolds stress tensor is proposed and used to view the stresses throughout the tip leakage vortex. Modeled Reynolds stresses using the Boussinesq approximation are obtained from the measured mean velocity strain rate tensor. The comparison of the principal directions and the three-dimensional graphic representations of the strain and Reynolds stress tensors aids in the understanding of the turbulence and what is required to model it.

Physical Explanations of Tip Leakage Flow Field in an Axial Compressor Rotor

1998 ◽  
Author(s):  
Masahiro Inoue ◽  
Masato Furukawa ◽  
Kazuhisa Saiki ◽  
Kazutoyo Yamada
Keyword(s):  
Boundary Layer ◽  
Vortex Core ◽  
Leakage Flow ◽  
Surface Boundary ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Vortex Lines

Structure of a tip leakage flow field in an axial compressor rotor has been investigated by detailed numerical simulations and appropriate post-processing. Physical explanations of the structure are made in terms of vortex-core identification, normalized helicity, vortex-lines, limiting streamlines, etc. The onset of the discrete tip leakage vortex is located on the suction surface at some distance from the leading edge. The vortex core with high vorticity is generated from a shear layer between the leakage jet flow and the main flow. The streamlines in the leakage flow are coiling around the vortex core. All the vortex-lines in the tip leakage vortex core link to ones in the suction surface boundary layer. The other vortex-lines in the suction surface boundary layer link to the vortex-lines in the pressure surface boundary layer and in the casing wall boundary layer. There are two mechanisms to reduce intensity of the tip leakage vortex: one is reduction of discharged vorticity caused by the linkage of vortex-lines between the suction surface and casing wall boundary layers, and another is diffusion of vorticity from the tip leakage vortex. Relative motion of the endwall has a substantial influence on the structure of the leakage flow field. In the case of a compressor rotor, it intensifies streamwise vorticity of the leakage vortex but reduces leakage flow loss.

Sign in / Sign up

Export Citation Format

Share Document