Development of a Low Emission Combustor for a 100kW Automotive Ceramic Gas Turbine: I

1993 ◽  
Author(s):  
Masafumi Sasaki ◽  
Hirotaka Kumakura ◽  
Daishi Suzuki ◽  
Katsuhiko Sugiyama ◽  
Youichirou Ohkubo
Keyword(s):  
Gas Turbine ◽  
Inlet Temperature ◽  
Performance Tests ◽  
Combustion System ◽  
Passenger Cars ◽  
Temperature Level ◽  
Fuel Injectors ◽  
Low Emission ◽  
Ceramic Components ◽  
Suitable System

A low emission combustor for a 100kW ceramic gas turbine, which is intended to meet Japanese emission standards for gasoline passenger cars, has been designed and subjected to initial performance tests. A prevaporization-premixing combustion system was chosen as the most suitable system for the combustor. The detailed combustor design, including the use of ceramic components and fuel injectors, was pursued taking into account the allowable engine dimensions for vehicle installation. In the initial performance tests conducted at a combustor inlet temperature of 773K, a low NOx level was obtained that satisfied the steady state target at this temperature level.

Development of a Low-Emission Combustor for a 100-kW Automotive Ceramic Gas Turbine (II)

1996 ◽  
Vol 118 (1) ◽  
pp. 167-172 ◽  
Author(s):  
H. Kumakura ◽  
M. Sasaki ◽  
D. Suzuki ◽  
H. Ichikawa
Keyword(s):  
Gas Turbine ◽  
Gasoline Engine ◽  
Standard Test ◽  
Inlet Temperature ◽  
Performance Tests ◽  
Passenger Cars ◽  
Lean Combustion ◽  
Low Emission ◽  
Strength Tests ◽  
Combustion Tests

Performance tests were conducted on a low-emission combustor, which has a pre-vaporization–premixing lean combustion system and is designed for a 100 kW automotive ceramic gas turbine. The results of steady-state combustion tests performed at an inlet temperature of 1000–1200 K and pressure of 0.1–0.34 MPa indicate that the combustor would meet Japan’s emission standards for gasoline engine passenger cars without using an aftertreatment system. Flashback was suppressed by controlling the mixture velocity and air ratios. Strength tests conducted on rings and bars cut from the actual ceramic parts indicate that the combustor has nearly the same level of strength as standard test specimens.

scholarly journals Development of a Low-Emission Combustor for a 100-kW Automotive Ceramic Gas Turbine: II

1994 ◽  
Author(s):  
Hirotaka Kumakura ◽  
Masafumi Sasaki ◽  
Daishi Suzuki ◽  
Hiroyuki Ichikawa
Keyword(s):  
Gas Turbine ◽  
Gasoline Engine ◽  
Standard Test ◽  
Inlet Temperature ◽  
Combustion System ◽  
Passenger Cars ◽  
Lean Combustion ◽  
Low Emission ◽  
Strength Tests ◽  
Combustion Tests

Perfomance tests were conducted on a low-emission combustor which has a prevaporization-premixing lean combustion system and is designed for a 100 kW automotive ceramic gas turbine. The results of steady-state combustion tests performed at an inlet temperature of 1000–1200 K and pressure of 0.1–0.34 MPa indicate that the combustor would meet Japan’s emission standards for gasoline engine passenger cars without using an aftertreatment system. Flashback was suppressed by controlling the mixture velocity and air ratios. Strength tests conducted on rings and bars cut from the actual ceramic parts indicate that the combustor has nearly the same level of strength as standard test specimens.

Development of a Low-Emission Combustor for a 100-kW Automotive Ceramic Gas Turbine (III)

1996 ◽  
Author(s):  
Masafumi Sasaki ◽  
Hirotaka Kumakura ◽  
Daishi Suzuki ◽  
Hiroyuki Ichikawa ◽  
Youichiro Ohkubo ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Gas Turbine ◽  
Air Distribution ◽  
Performance Tests ◽  
Test Results ◽  
Combustion System ◽  
Stable Combustion ◽  
Lean Combustion ◽  
Low Emission ◽  
Combustion Region

A low emission combustor, which uses a prevaporization-premixing lean combustion system for the 100 kW automotive ceramic gas turbine (CGT), has been subjected to performance tests. Now a second combustor prototype (PPL-2), which incorporates improvements intended to overcome a flashback problem observed in an initial combustor prototype (PPL-1), is tested. The PPL-2 has been designed and built, so that it will substantially expand the stable combustion range. The improvement is accomplished by increasing the air distribution ratio in the lean combustion region to avoid flashback, providing a uniform flow velocity through the throat area and also by diluting the boundary layer so as to suppress flashback. Test results of the PPL-2 combustor show that it expands the flashback limit without affecting the blow out limit and is able to cover the stable combustion range need for the 100kW CGT.

scholarly journals Development of 300 kW Class Ceramic Gas Turbine (CGT302)

1995 ◽  
Author(s):  
Kozi Nishio ◽  
Junzo Fujioka ◽  
Tetsuo Tatsumi ◽  
Isashi Takehara
Keyword(s):  
Gas Turbine ◽  
Development Program ◽  
Pollutant Emissions ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Turbine Inlet Temperature ◽  
Iso Standard ◽  
Current State ◽  
Ceramic Components

With the aim of achieving higher efficiency, lower pollutant emissions, and multi-fuel capability for small to medium-sized gas turbine engines for use in co-generation systems, a ceramic gas turbine (CGT) research and development program is being promoted by the Japanese Ministry of International Trade and Industry (MITI) as a part of its “New Sunshine Project”. Kawasaki Heavy Industries (KHI) is participating in this program and developing a regenerative two-shaft CGT (CGT302). In 1993, KHI conducted the first test run of an engine with full ceramic components. At present, the CGT302 achieves 28.8% thermal efficiency at a turbine inlet temperature (TIT) of 1117°C under ISO standard conditions and an actual TIT of 1250°C has been confirmed at the rated speed of the basic CGT. This paper consists of the current state of development of the CGT302 and how ceramic components are applied.

Status of the Automotive Ceramic Gas Turbine Development Program: Year Five Progress

1996 ◽  
Author(s):  
Tsubura Nisiyama ◽  
Norio Nakazawa ◽  
Masafumi Sasaki ◽  
Masumi Iwai ◽  
Haruo Katagiri ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Development Program ◽  
Ceramic Materials ◽  
Inlet Temperature ◽  
Test Rig ◽  
Target Values ◽  
Ceramic Components ◽  
Combined Test ◽  
And Performance ◽  
The Individual

Petroleum Energy Center of Japan has been carrying out a 7-year development program to prove the potential of an automotive ceramic gas turbine for five years with the support of the Ministry of International Trade and Industry. The ceramic gas turbine now under development is a regenerative single shaft engine. The output is 100kW, and the turbine inlet temperature (TIT) is 1350°C. All the ceramic components are now entering the 1350°C TIT test phase after completing 1200°C TIT evaluation tests, including durability tests, in various types of test rigs. The compressor-turbine combined test rig and the full assembly test rig which is the same as an actual engine and incorporates all the components are now going through 1200°C TIT function and performance evaluation tests. In the near future, we are planning to increase the TIT to 1350°C. In consideration of the current level of high-temperature, long-term strength available from the ceramic materials, we decided to change the rated speed to 100,000 rpm because the initial rated speed of 110,000 rpm, if unchanged, involves considerable risks. Then we reviewed mainly the designs of the compressor and turbine and revised the target values of the individual components to match the specifications that satisfy the target performance of the engine.

scholarly journals Development of a Catalytic Combustor for a Heavy-Duty Utility Gas Turbine

1996 ◽  
Author(s):  
Ralph A. Dalla Betta ◽  
James C. Schlatter ◽  
Sarento G. Nickolas ◽  
Martin B. Cutrone ◽  
Kenneth W. Beebe ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Catalytic Combustion ◽  
Full Scale ◽  
Inlet Temperature ◽  
Nox Emissions ◽  
Combustion System ◽  
Catalytic Reactor ◽  
Heavy Duty ◽  
Catalytic Combustor

The most effective technologies currently available for controlling NOx emissions from heavy-duty industrial gas turbines are either diluent injection in the combustor reaction zone, or lean premixed Dry Low NOx (DLN) combustion. For ultra low emissions requirements, these must be combined with selective catalytic reduction (SCR) DeNOx systems in the gas turbine exhaust. An alternative technology for achieving comparable emissions levels with the potential for lower capital investment and operating cost is catalytic combustion of lean premixed fuel and air within the gas turbine. The design of a catalytic combustion system using natural gas fuel has been prepared for the GE model MS9OOIE gas turbine. This machine has a turbine inlet temperature to the first rotating stage of over 1100°C and produces approximately 105 MW electrical output in simple cycle operation. The 508 mm diameter catalytic combustor designed for this gas turbine was operated at full-scale conditions in tests conducted in 1992 and 1994. The combustor was operated for twelve hours during the 1994 test and demonstrated very low NOx emissions from the catalytic reactor. The total exhaust NOx level was approximately 12–15 ppmv and was produced almost entirely in the preburner ahead of the reactor. A small quantity of steam injected into the preburner reduced the NOx emissions to 5–6 ppmv. Development of the combustion system has continued with the objectives of reducing CO and UHC emissions, understanding the parameters affecting reactor stability and spatial non-uniformities which were observed at low inlet temperature, and improving the structural integrity of the reactor system to a level required for commercial operation of gas turbines. Design modifications were completed and combustion hardware was fabricated for additional full-scale tests of the catalytic combustion system in March 1995 and January 1996. This paper presents a discussion of the combustor design, the catalytic reactor design and the results of full-scale testing of the improved combustor at MS9OOIE cycle conditions in the March 1995 and January 1996 tests. Major improvements in performance were achieved with CO and UHC emissions of 10 ppmv and 0 ppmv at base load conditions. This ongoing program will lead to two additional full-scale combustion system tests in 1996. The results of these tests will be available for discussion at the June 1996 Conference in Birmingham.

scholarly journals Combustion of LCV Coal Derived Fuel Gas for High Temperature, Low Emissions Gas Turbines in the British Coal Topping Cycle

1991 ◽  
Author(s):  
G. J. Kelsall ◽  
M. A. Smith ◽  
H. Todd ◽  
M. J. Burrows
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Calorific Value ◽  
Pollutant Emissions ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Combustion System ◽  
Fuel Gas ◽  
Gas Turbine Combustion ◽  
Topping Cycle

Advanced coal based power generation systems such as the British Coal Topping Cycle offer the potential for high efficiency electricity generation with minimum environmental impact. An important component of the Topping Cycle programme is the development of a gas turbine combustion system to burn low calorific value (3.5–4.0 MJ/m3 wet gross) coal derived fuel gas, at a turbine inlet temperature of 1260°C, with minimum pollutant emissions. The paper gives an overview of the British Coal approach to the provision of a gas turbine combustion system for the British Coal Topping Cycle, which includes both experimental and modelling aspects. The first phase of this programme is described, including the design and operation of a low-NOx turbine combustor, operating at an outlet temperature of 1360°C and burning a synthetic low calorific value (LCV) fuel gas, containing 0 to 1000 ppmv of ammonia. Test results up to a pressure of 8 bar are presented and the requirements for further combustor development outlined.

Summary of CGT302 Ceramic Gas Turbine Research and Development Program

2000 ◽  
Author(s):  
Isashi Takehara ◽  
Tetsuo Tatsumi ◽  
Yoshihiro Ichikawa
Keyword(s):  
Research And Development ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
High Efficiency ◽  
Development Program ◽  
Pollutant Emissions ◽  
Inlet Temperature ◽  
Term Operation ◽  
Ceramic Components

The Japanese Ceramic Gas Turbine (CGT) research and development program (FY1988–1998) as a part of the New Sunshine Project funded by the Ministry of International Trade and Industry (MITI) was completed in March 1999. Kawasaki Heavy Industries, Ltd. (KM) participated in this research program from the beginning and developed a twin-shaft CGT with a recuperator, designated as the “CGT302”. The purposes of this program were: 1) to achieve both a high efficiency and low pollutant emissions level using ceramic components, 2) to prove a multi-fuel capability to be used in co-generation systems, and 3) to demonstrate long-term operation. The targets of this program were: i) to achieve a thermal efficiency of over 42% at a turbine inlet temperature (TIT) of 1350°C, ii) to keep its emissions within the regulated value by the law, and iii) to demonstrate continuous operation for more than a thousand hours at 1200°C TIT. The CGT302 has successfully attained its targets. In March 1999 the CGT302 recorded 42.1% thermal efficiency, and 31.7 ppm NOx emissions (O2 = 16%) at 1350°C TIT. At this time it had also accumulated over two thousand hours operation at 1200°C. In this paper, we summarize the development of the CGT302.

Sign in / Sign up

Export Citation Format

Share Document