Experimental and Numerical Conjugate Flow and Heat Transfer Investigation of a Shower-Head Cooled Turbine Guide Vane

1997 ◽  
Author(s):  
Dieter E. Bohn ◽  
Volker J. Becker ◽  
Agnes U. Rungen
Keyword(s):  
Heat Transfer ◽  
Thermal Analysis ◽  
Guide Vane ◽  
Leading Edge ◽  
Operating Conditions ◽  
Main Stream ◽  
Temperature Ratio ◽  
Stagnation Line ◽  
Flow And Heat Transfer ◽  
Turbine Guide Vane

This paper presents investigations of the development for a shower-head cooling configuration for a modern industrial turbine guide vane. One aim is to find suitable locations for cooling gas ejection with the lowest cooling gas mass flow possible. The investigations begin with a numerical experiment. After the prediction of a suitable configuration and operating parameters, the aerodynamics are investigated experimentally using a non-intrusive LDA technique. Once the aerodynamics had been validated, the numerical experiments were expanded to a thermal analysis of the vane. Our conjugate flow and heat transfer simulation enables thermal analysis of the vane body without us having to derive any heat transfer data beforehand. The calculations were performed for a temperature ratio of 0.5 between cooling gas and main stream. This temperature ratio is similar to the operating conditions found in current designs. The stagnation line moves under the influence of cooling gas ejection, which significantly influences the cooling gas distribution on the vane surface. The temperature distribution inside the vane is compared to a non-cooled test case. The simulation shows that the temperature peaks at the leading edge are reduced by between 18% and 44%.

3-D Conjugate Flow and Heat Transfer Investigations of a Film-Cooled Turbine Guide Vane With Different Blowing Ratios

1997 ◽  
Author(s):  
Dieter E. Bohn ◽  
Tom Heuer ◽  
Karsten A. Kusterer
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Guide Vane ◽  
Leading Edge ◽  
Cooling Fluid ◽  
Hot Gas ◽  
Flow And Heat Transfer ◽  
Passage Vortex ◽  
Turbine Guide Vane ◽  
Conjugate Calculation

Film-cooling has become a widely used cooling method in present day gas turbines. Cooling gas ejection at the leading edge serves to protect the entire vane surface from contact with the hot gas. With doing this, material temperatures are reduced in order to guarantee an economically acceptable life span of the vane. This paper describes the application of a numerical method for the conjugate calculation of internal and external fluid flows and the heat transfer in and through the blade walls of a film-cooled turbine guide vane. The advantage of this approach is that it is possible to predict fluid flow properties and wall temperatures without the need for additional heat transfer conditions or temperature conditions at the external surfaces of the vane. This is a great advantage because the desired data are either unknown or not available for the calculation in the design process of new cooled blades or vanes. In a complete calculation of external and internal flows, no additional boundary conditions at the internal surfaces of the cooling geometry are needed either. Another advantage is the interaction of fluid flow and heat transfer which is taken into account by the conjugate calculation. In the 3-D numerical experiment to be presented, the influence of leading edge cooling fluid ejection on the temperature distribution in the vane material is investigated. The cooling fluid is ejected through two slots at the leading edge. The calculations are performed for three blowing ratios in order to investigate the efficiency of the cooling method. Realistic temperature ratios of cooling-fluid flow and main flow are considered. Such information is very useful in the aero thermal design process of new cooling configurations, since the amount of experimental work can be minimized. The results show the influence of complex 3-D flow phenomena (e.g. passage vortex) on the cooling fluid distribution on the vane surface as a function of the chosen blowing factor. Due to the influence of the passage vortex, the cooling fluid is displaced and leaves the vane surface near the side-wall uncovered against the hot gas. Furthermore, cooling fluid displacement on the pressure side according to the ejection slot geometry leads to another unprotected region on the vane surface. These effects have severe consequences on the thermal load of the vane and can reduce its life span.

Effects of Upstream Step Geometry on Axisymmetric Converging Vane Endwall Secondary Flow and Heat Transfer at Transonic Conditions

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Zhigang Li ◽  
Luxuan Liu ◽  
Jun Li ◽  
Ridge A. Sibold ◽  
Wing F. Ng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Secondary Flow ◽  
Thermal Load ◽  
Numerical Study ◽  
Guide Vane ◽  
Leading Edge ◽  
Step Height ◽  
Temperature History ◽  
Flow And Heat Transfer ◽  
High Thermal Load

This paper presents a detailed experimental and numerical study on the effects of upstream step geometry on the endwall secondary flow and heat transfer in a transonic linear turbine vane passage with axisymmetric converging endwalls. The upstream step geometry represents the misalignment between the combustor exit and the nozzle guide vane endwall. The experimental measurements were performed in a blowdown wind tunnel with an exit Mach number of 0.85 and an exit Re of 1.5×106. A high freestream turbulence level of 16% was set at the inlet, which represents the typical turbulence conditions in a gas turbine engine. Two upstream step geometries were tested for the same vane profile: a baseline configuration with a gap located 0.88Cx (43.8 mm) upstream of the vane leading edge (upstream step height = 0 mm) and a misaligned configuration with a backward-facing step located just before the gap at 0.88Cx (43.8 mm) upstream of the vane leading edge (step height = 4.45% span). The endwall temperature history was measured using transient infrared thermography, from which the endwall thermal load distribution, namely, Nusselt number, was derived. This paper also presents a comparison with computational fluid dynamics (CFD) predictions performed by solving the steady-state Reynolds-averaged Navier–Stokes with Reynolds stress model using the commercial CFD solver ansysfluent v.15. The CFD simulations were conducted at a range of different upstream step geometries: three forward-facing (upstream step geometries with step heights from −5.25% to 0% span), and five backward-facing, upstream step geometries (step heights from 0% to 6.56% span). These CFD results were used to highlight the link between heat transfer patterns and the secondary flow structures and explain the effects of upstream step geometry. Experimental and numerical results indicate that the backward-facing upstream step geometry will significantly enlarge the high thermal load region and result in an obvious increase (up to 140%) in the heat transfer coefficient (HTC) level, especially for arched regions around the vane leading edge. However, the forward-facing upstream geometry will modestly shrink the high thermal load region and reduce the HTC (by ∼10% to 40% decrease), especially for the suction side regions near the vane leading edge. The aerodynamic loss appears to have a slight increase (0.3–1.3%) because of the forward-facing upstream step geometry but is slightly reduced (by 0.1–0.3%) by the presence of the backward upstream step geometry.

A Conjugate 3-D Flow and Heat Transfer Analysis of a Thermal Barrier Cooled Turbine Guide Vane

1998 ◽  
Author(s):  
Dieter E. Bohn ◽  
Volker J. Becker
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Guide Vane ◽  
Suction Side ◽  
Heat Transfer Analysis ◽  
Thermal Barrier ◽  
Trailing Edge ◽  
Flow And Heat Transfer ◽  
Turbine Guide Vane ◽  
Basic Configuration

This paper presents the numerical investigations of the flow and heat transfer of two configurations of a transonic turbine guide vane. The basic configuration is a vane with convection cooling. The second configuration is additionally coated with a thermal barrier consisting of ZrO2. The results are obtained with a conjugate heat transfer and flow computer code that has been developed at the Institute of Steam and Gas Turbines. Measurement data is available for the basic configuration and the computational results are compared to the experimental results. The results show very good agreement between calculated and measured vane surface temperatures. The trailing edge turns out to be subjected to high thermal loads as it is too thin to be cooled effectively. Secondary flow phenomena like the passage vortex and the corner vortex and their impact on the temperature distribution are discussed. The ZrO2 coating is calculated for a thickness of 300μm. The substrate material temperatures are lowered by about 20 K–29 K in the stagnation point area and by about 27 K–43 K in the shock area on the suction side. At the trailing edge, the coating on the suction side and on the pressure side hardly influences the metal temperature.

Turning Guide Vane Effect on Internal Cooling of Two-Passage Channel With Parallel Ribs

2020 ◽  
Vol 142 (9) ◽  
Author(s):  
Mandana S. Saravani ◽  
Ryoichi S. Amano ◽  
Nicholas J. DiPasquale ◽  
Joseph Wayne Halmo
Keyword(s):  
Heat Transfer ◽  
Guide Vane ◽  
Constant Heat Flux ◽  
Operating Conditions ◽  
Internal Cooling ◽  
Flux Boundary Condition ◽  
Flow And Heat Transfer ◽  
Computational Fluid Dynamics Simulations ◽  
Heat Flux Boundary Condition ◽  
Dynamics Simulations

Abstract The present work investigates the effects of various guide vane designs on the heat transfer enhancement of rotating U-duct configuration with parallel 45-deg ribs. The ribs were installed on the bottom wall of the channel, which has a constant heat flux boundary condition. The channel has a square cross section with a 5.08 cm hydraulic diameter. The first and second passes are 514 mm and 460 mm, respectively. The range of Reynolds number for turbulent flow is up to 35,000. The channel rotates at various speeds up to 600 rpm, which brings the maximum rotation number of 0.75. Several computational fluid dynamics simulations are carried out for this study to understand the effect of guide vanes on flow and heat transfer in serpentine channels under various operating conditions.

Experimental and Numerical Conjugate Investigation of the Blowing-Ratio Influence on the Showerhead Cooling Efficiency

1998 ◽  
Author(s):  
Dieter E. Bohn ◽  
Volker J. Becker ◽  
Karsten A. Kusterer ◽  
Agnes U. Rungen
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Guide Vane ◽  
Leading Edge ◽  
Suction Side ◽  
Computer Code ◽  
Inlet Temperature ◽  
Cooling Efficiency ◽  
Blowing Ratio ◽  
Turbine Guide Vane

This paper presents the experimental investigation of the flow and the numerical analysis of the flow and heat transfer in a turbine guide vane with showerhead cooling for two different blowing ratios. The aerodynamic results are compared with those of the experiments. Starting with a showerhead design of two rows of ejection holes, two additional rows have to be used in an enhanced design due to hot gas contact in the leading edge area. Thus, the cooling gas mass flow is doubled when keeping the blowing ratio constant at m = 1.5. Lowering the amount of cooling gas needed whilst still guaranteeing sufficient cooling is the motivation for the analysis of the influence of a lower blowing ratio on the cooling efficiency. The investigated blowing ratios are m = 1.5 and m = 1.0. The experiments are conducted using a non-intrusive LDA technique. The numerical results are gained with a conjugate heat transfer and flow computer code that has been developed at the Institute of Steam and Gas Turbines. The results show that the blowing ratio has to be chosen carefully as the leading edge flow pattern and the heat transfer are strongly influenced by the blowing ratio. Lower blowing ratios lead to a better attachment of the cooling film and thus they hardly disturb the main flow. With the lower blowing ratio, the material temperature increases up to 1.5% of the total inlet temperature in the leading edge area on the pressure side, whereas it decreases locally for about 0.8% for the lower blowing ratio on the suction side. This is due to the enhanced attachment of the cooling gas film.

Application of the Turbulent Potential Model to Heat Transfer Predictions on a Turbine Guide Vane

2006 ◽  
Author(s):  
Rene Pecnik ◽  
Wolfgang Sanz
Keyword(s):  
Heat Transfer ◽  
Pressure Gradient ◽  
Potential Model ◽  
Guide Vane ◽  
Measurement Data ◽  
Operating Conditions ◽  
Boundary Layer Transition ◽  
Test Cases ◽  
Layer Transition ◽  
Turbine Guide Vane

The accurate numerical simulation of the flow through turbomachinery depends on the reliable prediction of laminar to turbulent boundary layer transition phenomena. The aim of this paper is to study the ability of the turbulent potential model to predict those non-equilibrium turbulent flows for several test cases. Within this model turbulent quantities are described by the turbulent scalar and turbulent vector potentials of the turbulent body force — the divergence of the Reynolds stress tensor. For model validation firstly flat plate test cases with different inlet turbulence intensities, zero pressure gradient and non-uniform pressure gradient distributions along the plate were calculated and compared by means of skin friction values measured in the experiments. Finally the model was validated by heat transfer measurement data obtained from a highly loaded transonic turbine guide vane cascade for different operating conditions.

Investigation on the Internal Cooling of Two-Passage Channels With Parallel Ribs and Guide Vanes

2019 ◽  
Author(s):  
Ryoichi S. Amano ◽  
Mandana S. Saravani ◽  
Nicholas DiPasquale
Keyword(s):  
Heat Transfer ◽  
Guide Vane ◽  
Constant Heat Flux ◽  
Operating Conditions ◽  
Internal Cooling ◽  
Flux Boundary Condition ◽  
Guide Vanes ◽  
Flow And Heat Transfer ◽  
Speed Up ◽  
Dynamics Simulations

Abstract The present work investigates the effects of various guide vane designs on the heat transfer enhancement of rotating U-Duct configuration with parallel 45-deg ribs. The ribs were installed on the bottom wall of the channel which has a constant heat flux boundary condition. The channel has a square cross-section with a 5.08 cm (2 in) hydraulic diameter. The first and second passes are 514 mm and 460 mm, respectively. The range of Reynolds number for turbulent flow is up to 35,000. The channel rotates in various speed up to 600 rpm which brings the maximum rotation number of 0.75. Several computational fluid dynamics simulations are carried out for this study to understand the effect of guide vanes on flow and heat transfer in serpentine channels under various operating conditions.

Application of the Turbulent Potential Model to Heat Transfer Predictions on a Turbine Guide Vane

2006 ◽  
Vol 129 (3) ◽  
pp. 628-635 ◽  
Author(s):  
Rene Pecnik ◽  
Wolfgang Sanz
Keyword(s):  
Heat Transfer ◽  
Pressure Gradient ◽  
Potential Model ◽  
Guide Vane ◽  
Measurement Data ◽  
Operating Conditions ◽  
Boundary Layer Transition ◽  
Test Cases ◽  
Layer Transition ◽  
Turbine Guide Vane

The accurate numerical simulation of the flow through turbomachinery depends on the reliable prediction of laminar to turbulent boundary layer transition phenomena. The aim of this paper is to study the ability of the turbulent potential model to predict those nonequilibrium turbulent flows for several test cases. Within this model turbulent quantities are described by the turbulent scalar and turbulent vector potentials of the turbulent body force—the divergence of the Reynolds stress tensor. For model validation first flat plate test cases with different inlet turbulence intensities, zero pressure gradient, and nonuniform pressure gradient distributions along the plate were calculated and compared by means of skin friction values measured in the experiments. Finally the model was validated by heat transfer measurement data obtained from a highly loaded transonic turbine guide vane cascade for different operating conditions.

Film cooling on a turbine guide vane: A numerical analysis with a multigrid technique

2001 ◽  
Vol 215 (1) ◽  
pp. 39-53 ◽  
Author(s):  
S Sarkar ◽  
K Das ◽  
D Basu
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Guide Vane ◽  
Navier Stokes ◽  
Time Stepping ◽  
Flow And Heat Transfer ◽  
Local Time Stepping ◽  
Turbine Guide Vane ◽  
Nozzle Guide ◽  
Internal Convection

The flow and heat transfer due to film cooling over a turbine nozzle guide vane, which was also cooled by internal convection, were numerically analysed under engine conditions. The time-dependent, two-dimensional, mass-averaged, Navier-Stokes (N-S) equations are solved in the physical plane based on the four-stage Runge-Kutta algorithm in the finite volume formulation. Local time stepping, variable coefficient implicit residual smoothing and a full multigrid technique have been implemented to accelerate the steady state calculations. Turbulence was simulated by the algebraic Baldwin-Lomax (B-L) model. The computed heat transfer distributions with film cooling in conjunction was successful in describing the coolant behavior over the curved suction and pressure surfaces of a turbine blade for varying blowing and temperature ratios.

Sign in / Sign up

Export Citation Format

Share Document