Experimental Investigation on the Electrokinetic Motions of Colloidal Particles at an Interfacial Boundary Between Solid and Liquid

Author(s):  
Katsuaki Shirai ◽  
Shoichiro Kaji ◽  
Shigeo Hosokawa ◽  
Tsuyoshi Kawanami ◽  
Shigeki Hirasawa

Abstract We investigate electrokinetic behavior of colloidal particles in the vicinity of a solid-liquid interface. Colloidal liquids are expected to be used as thermal transport media for heat transfer applications such as nanofluids and phase change emulsions. They contain submicrometer-sized particles in liquid, and electrokinetic behavior of the solute particles should play an important role in the heat transfer between solid-liquid interfacing boundaries. However, experimental investigation of the behavior remains difficult due to the required spatial resolution beyond diffraction limit. We developed a measurement system based on laser Doppler principle using an interference of evanescent waves generated at total internal reflections of incident lasers at a solid wall. The system was developed for the measurement of velocities of colloidal particles at an interfacing boundary of colloidal liquid and a solid wall. The system has a unique advantage of a high spatial resolution in the direction perpendicular to the boundary due to the short penetration depth of an evanescent wave in the range of a few hundred nanometers. The principle and performance of the measurement system were investigated using a scanning probe in the measurement volume. We experimentally confirmed the validity of the measurement and characterized the uncertainty of velocity measurement. The system was further applied in a series of measurements of alumina particles dispersed in water in a square-shaped cell under induced electric fields. The measured velocities are proportional to the field strengths at different particle concentrations. The linear relationship is consistent with theoretical predictions, which demonstrates the feasibility of the system for the measurement of velocities of colloidal particles in the near wall region.

1985 ◽  
Vol 107 (1) ◽  
pp. 44-51 ◽  
Author(s):  
B. Kalhori ◽  
S. Ramadhyani

An experimental investigation of melting and cyclic melting and freezing around a vertical cylinder is reported. The studies encompass two cases: a plain vertical cylinder, and a vertical cylinder with fins. In the melting studies, the total heat transfer from the cylinder was measured as a function of time. In addition, measurements have been made of the solid-liquid interface shape after various melting times. In these studies, the solid phase was initially isothermal and either at its fusion temperature or subcooled below the fusion point. The experiments reveal the important influence of natural convection in the liquid phase in both unfinned and finned situations. Subcooling of the solid phase is observed to strongly inhibit heat transfer in the unfinned situation. In the experiment on cyclic melting and freezing, subcooling of the solid phase is once again found to have an important effect on the unfinned situation. Heat transfer from the finned cylinder is much less affected by solid-phase subcooling. All the experiments were performed with 99 percent pure n-eicosane paraffin.


An experimental investigation has been carried out for heat transfer enhancement over dimpled surface using spoiler turbulators. The experimentation is carried out over the aluminum plate of 1000 mm x 10 mm x 5 mm and Reynolds number ranging from 10,000 to 33,000. The δ/d ratio for dimple is 0.3, which is kept constant. The pitch for dimples are varied as 16 mm, 18 mm and 20 mm. Turbulators were used over the dimples surface in inline and staggered arrangement which provides different flow structure and produces turbulence. Turbulators are mounted over dimples at an angle of 12o with respect to flat plate. Experimental results were validated using Dittus-Boelter and Blasius equations. Analysis is made using Nusselt number, friction factor and performance index. It has been found that compared to dimpled plate performance of dimpled surface with spoiler tabulator plate is higher. If we compare inline and staggered arrangement, performance of inline arrangement dimple plate with turbulator is higher compared to staggered arrangement. This is due to in staggered arrangement at some locations chocking of flow may takes place which reduces heat transfer rate.


Sign in / Sign up

Export Citation Format

Share Document