Experimental Adiabatic Two-Phase Pressure Drops of R134a, R236fa and R245fa in Small Horizontal Circular Channels

2011 ◽  
Author(s):  
Chin L. Ong ◽  
John R. Thome
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Homogeneous Model ◽  
Prediction Methods ◽  
Two Phase ◽  
Pressure Drops ◽  
Wide Range ◽  
Small Channels ◽  
Experimental Pressure ◽  
Phase Pressure

Experimental adiabatic two-phase pressure drops data for refrigerants R134a, R236fa and R245fa during flow boiling in small channels with internal diameters of 1.03, 2.20 and 3.04 mm are presented. The main purpose was to investigate the effects of channel confinement on adiabatic two-phase pressure drops. Thus, the two-phase pressure drop trends were systematically investigated over a wide range of test conditions for all three refrigerants and channel sizes. Statistical comparisons have also been made by comparing the experimental pressure drop data database with various macroscale and microscale prediction methods from the literature. The comparison showed relatively moderate accuracy for three prediction methods developed for macroscale flows, i.e. Baroczy and Chisholm, Friedel and the homogeneous model with the Cicchitti et al. viscosity relation. As for microscale prediction methods, the Cioncolini et al. annular flow model worked best with 68.5% of the data within ± 30%, followed by the Sun and Mishima and the Zhang et al. methods. Combining this database with the LTCM lab’s earlier database for 0.509 and 0.790 mm channels, there appears to be no evidence of a macro-to-microscale transition, at least with respect to two-phase pressure drops.

Two Phase Pressure Drops for Refrigerants: A Statistical Comparison Among Experimental Data and Correlations

2006 ◽  
Author(s):  
Adriana Greco ◽  
Rita Mastrullo ◽  
Alfonso W. Mauro ◽  
Giuseppe P. Vanoli
Keyword(s):  
Experimental Data ◽  
Horizontal Tube ◽  
Operating Conditions ◽  
Prediction Methods ◽  
Two Phase Flows ◽  
Two Phase ◽  
Pressure Drops ◽  
Statistical Comparison ◽  
Wide Range ◽  
Phase Pressure

A 962 points database for refrigerants two-phase flows by Greco A. and Vanoli G.P. was statistically compared to four widely used prediction methods by Lockhart and Martinelli, Chawla, Theissing and Mu¨ller-Steinhagen and Heck in order to determine the best one. The experimental points are in a wide range of operating conditions for six pure or mixed refrigerants (R134a, R22, R407C, R507A, R410A and R404A) during evaporation in a smooth horizontal tube of 6 m length and 6 mm ID.

Experimental Investigation of Flow Boiling Pressure Drop of R134A in a Microscale Horizontal Smooth Tube

2011 ◽  
Vol 3 (1) ◽  
Author(s):  
Cristiano Bigonha Tibiriçá ◽  
Jaqueline Diniz da Silva ◽  
Gherhardt Ribatski
Keyword(s):  
Pressure Drop ◽  
High Speed ◽  
Flow Boiling ◽  
Smooth Tube ◽  
Working Fluid ◽  
Prediction Methods ◽  
Internal Diameter ◽  
Two Phase ◽  
Pressure Drops ◽  
Frictional Pressure Drop

This paper presents new experimental flow boiling pressure drop results in a microscale tube. The experimental data were obtained under diabatic conditions in a horizontal smooth tube with an internal diameter of 2.32 mm. Experiments were performed with R134a as working fluid, mass velocities ranging from 100 kg/m2 s to 600 kg/m2 s, heat flux ranging from 10 kW/m2 to 55 kW/m2, saturation temperatures of 31°C, and exit vapor qualities from 0.20 to 0.99. Flow pattern characterization was also performed from images obtained by high-speed filming. Pressure drop gradients up to 48 kPa/m were measured. These data were carefully analyzed and compared against 13 two-phase frictional pressure drop prediction methods, including both macro- and microscale methods. Comparisons against these methods based on the data segregated according to flow patterns were also performed. Overall, the method by Cioncolini et al. (2009, “Unified Macro-to-Microscale Method to Predict Two-Phase Frictional Pressure Drops of Annular Flows,” Int. J. Multiphase Flow, 35, pp. 1138–1148) provided quite accurate predictions of the present database.

Two-phase pressure drop due to friction in micro-channel

2013 ◽  
Vol 228 (5) ◽  
pp. 921-931 ◽  
Author(s):  
Tae-Woo Lim ◽  
Sam-Sang You ◽  
Jong-Su Kim ◽  
Serng-Bae Moon ◽  
Dong-Hoan Seo
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Homogeneous Model ◽  
Absolute Error ◽  
Heat Fluxes ◽  
Micro Channel ◽  
Two Phase ◽  
Pressure Drops ◽  
Frictional Pressure Drop ◽  
New Correlation

This paper deals with an experimental investigation to measure the frictional pressure drops for two-phase flow boiling in a micro-channel with a hydraulic diameter of 500 µm. First, the experimental study is performed under the test conditions: heat fluxes ranging from 100 to 400 kW/m2, vapor qualities from 0 to 0.2, and mass fluxes of 200, 400 and 600 kg/m2s. Then, the frictional pressure drop during flow boiling is estimated using two models: the homogeneous model and the separated flow model. The experimental results show that the two-phase multiplier decreases with the increase of mass flux. In addition, the measured pressure drops are compared with those from a few correlation models available for macro-scales and mini/micro-scales. Finally, the present paper proposes a new correlation for two-phase frictional pressure drops in mini/micro-scales. This correlation model is developed based on the Chisholm constant C as a function of two-phase Reynolds and Weber numbers. It is found that the new correlation satisfactorily predicts the experimental data within mean absolute error (MAE) of 3.9%.

High Heat Flux Subcooled Flow Boiling of Methanol in Microtubes

2015 ◽  
Author(s):  
Farzad Houshmand ◽  
Hyoungsoon Lee ◽  
Mehdi Asheghi ◽  
Kenneth E. Goodson
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Flow Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
Two Phase ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow ◽  
Inner Diameter ◽  
Phase Pressure

As the proper cooling of the electronic devices leads to significant increase in the performance, two-phase heat transfer to dielectric liquids can be of an interest especially for thermal management solutions for high power density devices with extremely high heat fluxes. In this paper, the pressure drop and critical heat flux (CHF) for subcooled flow boiling of methanol at high heat fluxes exceeding 1 kW/cm2 is investigated. Methanol was propelled into microtubes (ID = 265 and 150 μm) at flow rates up to 40 ml/min (mass fluxes approaching 10000 kg/m2-s), boiled in a portion of the microtube by passing DC current through the walls, and the two-phase pressure drop and CHF were measured for a range of operating parameters. The two-phase pressure drop for subcooled flow boiling was found to be significantly lower than the saturated flow boiling case, which can lead to lower pumping powers and more stability in the cooling systems. CHF was found to be increasing almost linearly with Re and inverse of inner diameter (1/ID), while for a given inner diameter, it decreases with increasing heated length.

INVESTIGATION ON VOID FRACTION FOR TWO-PHASE FLOW PRESSURE DROP OF EVAPORATIVE R-290 IN HORIZONTAL TUBE

2016 ◽  
Vol 78 (8-4) ◽  
Author(s):  
Agus Sunjarianto Pamitran ◽  
Sentot Novianto ◽  
Normah Mohd-Ghazali ◽  
Nasruddin Nasruddin ◽  
Raldi Koestoer
Keyword(s):  
Pressure Drop ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Homogeneous Model ◽  
Saturation Temperature ◽  
Horizontal Tube ◽  
Phase Flow ◽  
Two Phase ◽  
Experimental Conditions

Two-phase flow boiling pressure drop experiment was conducted to observe its characteristics and to develop a new correlation of void fraction based on the separated model. Investigation is completed on the natural refrigerant R-290 (propane) in a horizontal circular tube with a 7.6 mm inner diameter under experimental conditions of 3.7 to 9.6 °C saturation temperature, 10 to 25 kW/m2 heat flux, and 185 to 445 kg/m2s mass flux. The present experimental data was used to obtain the calculated void fraction which then was compared to the predicted void fraction with 31 existing correlations. A new void fraction correlation for predicting two-phase flow boiling pressure drop, as a function of Reynolds numbers, was proposed. The measured pressure drop was compared to the predicted pressure drop with some existing pressure drop models that use the newly developed void fraction model. The homogeneous model of void fraction showed the best prediction with 2% deviation

Two-Phase Pressure Drop and Boiling Heat Transfer in a Single Horizontal Microchannel

2006 ◽  
Author(s):  
Cheol Huh ◽  
Moo Hwan Kim
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Local Flow ◽  
Heat Transfer Coefficients ◽  
Phase Pressure

With a single microchannel and a series of microheaters made with MEMS technique, two-phase pressure drop and local flow boiling heat transfer were investigated using deionized water in a single horizontal rectangular microchannel. The test microchannel has a hydraulic diameter of 100 μm and length of 40 mm. A real time observation of the flow patterns with simultaneous measurement are made possible. Tests are performed for mass fluxes of 90, 169, and 267 kg/m2s and heat fluxes of from 100 to 600 kW/m2. The experimental local flow boiling heat transfer coefficients and two-phase frictional pressure gradient are evaluated and the effects of heat flux, mass flux, and vapor qualities on flow boiling are studied. Both the evaluated experimental data are compared with existing correlations. The experimental heat transfer coefficients are nearly independent on mass flux and the vapor quality. Most of all correlations do not provide reliable heat transfer coefficients predictions with vapor quality and prediction accuracy. As for two-phase pressure drop, the measured pressure drop increases with the mass flux and heat flux. Most of all existing correlations of two-phase frictional pressure gradient do not predict the experimental data except some limited conditions.

scholarly journals Flow boiling of water in a minichannel: The effects of surface wettability on two-phase pressure drop

2011 ◽  
Vol 31 (11-12) ◽  
pp. 1894-1905 ◽  
Author(s):  
Hai Trieu Phan ◽  
Nadia Caney ◽  
Philippe Marty ◽  
Stéphane Colasson ◽  
Jérôme Gavillet
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Surface Wettability ◽  
Two Phase ◽  
Phase Pressure
Sign in / Sign up

Export Citation Format

Share Document