Evaluation of Vertical Wall-To-Guardrail Transition

2008 ◽  
Author(s):  
Ali O. Atahan ◽  
Guido Bonin ◽  
Moustafa El-Gindy
Keyword(s):  
Gradual Increase ◽  
Vertical Wall ◽  
Element Model ◽  
Impact Performance ◽  
Injury Criteria ◽  
Crash Testing ◽  
Transition Barrier ◽  
Occupant Injury ◽  
Heavy Truck ◽  
The Impact

Transition barriers are used to connect longitudinal barriers that have different stiffnesses. They are designed to provide a gradual increase in stiffness towards the stiffer barrier section. In this study, a W-beam rail and a W-beam rubrail transition connecting a rigid bridge rail to a semi-rigid guardrail was evaluated using numerical and experimental methods. First, a finite element model of the transition design was constructed and validated using a 2000 kg pickup truck impact. Then, a series of vehicle models, i.e., 900 kg compact automobile, 8000 kg single unit truck and finally 30,000 kg heavy truck was used to evaluate the impact performance of the same transition design numerically. Simulation results predict that the double W-beam transition barrier performs acceptably in containing and redirecting all vehicles except 30,000 kg heavy truck. Occupant injury criteria were also found to be acceptable for all the cases, except 30,000 kg truck impact. Performing further simulations with vehicle sizes heavier than 8,000 kg that exist in crash testing guidelines is recommended to evaluate the acceptability limit of existing W-beam rail and a W-beam rubrail transition.

Crash Testing and Evaluation of Work Zone Traffic Control Devices

1998 ◽  
Vol 1650 (1) ◽  
pp. 45-54 ◽  
Author(s):  
King K. Mak ◽  
Roger P. Bligh ◽  
Lewis R. Rhodes
Keyword(s):  
Traffic Control ◽  
Evaluation Criteria ◽  
Work Zone ◽  
Work Zones ◽  
Impact Performance ◽  
Crash Testing ◽  
Control Devices ◽  
Traffic Control Devices ◽  
Under Construction ◽  
The Impact

Safety of work zones is a major area of concern since it is not always possible to maintain a level of safety comparable to that of a normal highway not under construction. Proper traffic control is critical to the safety of work zones. However, traffic control devices themselves may pose a safety hazard when impacted by errant vehicles. The impact performance of many work zone traffic control devices is mostly unknown, and little, if any, crash testing has been conducted in accordance with guidelines set forth in NCHRP Report 350. The Texas Department of Transportation (TxDOT) has, in recent years, sponsored a number of studies at the Texas Transportation Institute to assess the impact performance of various work zone traffic control devices, including plastic drums and sign substrates, temporary and portable sign supports, plastic cones, vertical panels, and barricades. The results, findings, conclusions, and recommendations are presented for temporary and portable sign supports, plastic drums, sign substrates for use with plastic drums, traffic cones, and vertical panels, whereas those for barricades are covered elsewhere. Most of the work zone traffic control devices satisfactorily met the evaluation criteria set forth in NCHRP Report 350 and are recommended for field implementation. However, some of the devices failed to perform satisfactorily and are not recommended for field applications. The results from these studies are being incorporated into the TxDOT barricade and construction standard sheets for use in work zones.

scholarly journals Crash Testing and Analysis of Work-Zone Sign Supports

2002 ◽  
Vol 1797 (1) ◽  
pp. 96-104 ◽  
Author(s):  
Karla A. Polivka ◽  
Ronald K. Faller ◽  
John R. Rohde ◽  
Dean L. Sicking
Keyword(s):  
Traffic Control ◽  
Work Zone ◽  
Work Zones ◽  
Design Elements ◽  
Impact Performance ◽  
Crash Testing ◽  
Control Devices ◽  
Traffic Control Devices ◽  
The Impact ◽  
Fundamental Design

A variety of traffic-controlling devices are used in work zones; some of these are not normally found on the roadside or in the traveled way outside of the work zones. These devices are used to enhance the safety of the work zones by controlling the traffic through these areas. Because of the placement of the traffic control devices, the devices themselves may be potentially hazardous to both workers and errant vehicles. The impact performance of many work-zone traffic control devices is mainly unknown, and to date limited crash testing has been conducted under the criteria of NCHRP Report 350: Recommended Procedures for the Safety Performance Evaluation of Highway Features. The results of full-scale crash testing of flexible panel work-zone sign stands were evaluated and analyzed to quantify the features that successful devices shared, as well as common features of those devices that failed salient safety criteria. Parameters considered included sign base and upright properties, sign height, cross-member properties, and ancillary details. Results pointed to three problematic, fundamental design issues: ( a) combinations of base and upright stiffness and strength that generally lead to significant windshield damage, ( b) cross members that lead to windshield damage in the end-on (90°) impact orientation, and ( c) appurtenances that have an impact on performance. Although there are a significant number of variables that control the performance of a given device, these generalizations offer a basis for the evaluation of the fundamental design elements.

scholarly journals Impact Performance Evaluation of a Crash Cushion Design Using Finite Element Simulation and Full-Scale Crash Testing

Safety ◽  
2018 ◽  
Vol 4 (4) ◽  
pp. 48
Author(s):  
Murat Büyük ◽  
Ali Atahan ◽  
Kenan Kurucuoğlu
Keyword(s):  
Finite Element ◽  
Performance Evaluation ◽  
Element Model ◽  
Full Scale ◽  
Plastic Energy ◽  
Impact Performance ◽  
Steel Cables ◽  
Energy Absorbing ◽  
The Impact ◽  
Crash Tests

Crash cushions are designed to gradually absorb the kinetic energy of an impacting vehicle and bring it to a controlled stop within an acceptable distance while maintaining a limited amount of deceleration on the occupants. These cushions are used to protect errant vehicles from hitting rigid objects, such as poles and barriers located at exit locations on roads. Impact performance evaluation of crash cushions are attained according to an EN 1317-3 standard based on various speed limits and impact angles. Crash cushions can be designed to absorb the energy of an impacting vehicle by using different material deformation mechanisms, such as metal plasticity supported by airbag folding or damping. In this study, a new crash cushion system, called the ulukur crash cushion (UCC), is developed by using linear, low-density polyethylene (LLDPE) containers supported by embedded plastic energy-absorbing tubes as dampers. Steel cables are used to provide anchorage to the design. The crashworthiness of the system was evaluated both numerically and experimentally. The finite element model of the design was developed and solved using LS-DYNA (971, LSTC, Livermore, CA, USA), in which the impact performance was evaluated considering the EN 1317 standard. Following the simulations, full-scale crash tests were performed to determine the performance of the design in containing and redirecting the impacting vehicle. Both the simulations and crash tests showed acceptable agreement. Further crash tests are planned to fully evaluate the crashworthiness of the new crash cushion system.

Manual for Assessing Safety Hardware Crash Testing and Evaluation of Multiple Mailbox Supports for Use with Locking Architectural Mailboxes

2019 ◽  
Vol 2673 (7) ◽  
pp. 684-695
Author(s):  
Chiara Silvestri Dobrovolny ◽  
Roger P. Bligh ◽  
Justin Obinna ◽  
Mark McDaniel ◽  
Wade Odell
Keyword(s):  
Evaluation Criteria ◽  
Department Of Transportation ◽  
Impact Performance ◽  
Critical Design ◽  
State Highway ◽  
Crash Testing ◽  
Texas Department ◽  
The Impact ◽  
Crash Tests ◽  
Highway System

With increasing concern about mail-identity theft, there is a growing demand among homeowners and businesses for the use of locking mailboxes for theft deterrence and resistance to vandalism. Lockable mailbox products can be significantly larger and heavier than standard lightweight mailboxes. Therefore, the Texas Department of Transportation (TxDOT) requested evaluation of their crashworthiness before permitting their use on the state highway system. Under TxDOT Project 9-1002-12, crash tests were performed following the Manual for Assessing Safety Hardware (MASH) guidelines and procedures to assess the impact performance of lockable, secure mailboxes in both single and multiple mount configurations. Testing of the larger and heavier locking mailboxes on multiple-mount support posts was unsuccessful owing to vehicle windshield deformation and intrusion. This paper describes the efforts to develop and evaluate the crashworthiness of new proposed designs for multiple mailbox supports used with a combination of lockable and standard mailboxes. The crash tests were performed following MASH guidelines and the evaluation criteria. Two proposed designs were evaluated through full-scale crash testing. Both systems satisfied all required MASH evaluation criteria at low and high impact speeds using a passenger car, which was considered to be the critical design vehicle based on the mailbox mounting height.

NCHRP Report 350 Compliance Tests of the ET-2000

1996 ◽  
Vol 1528 (1) ◽  
pp. 28-37 ◽  
Author(s):  
Hayes E. Ross ◽  
Wanda L. Menges ◽  
D. Lance Bullard
Keyword(s):  
Evaluation Criteria ◽  
Passenger Car ◽  
Roadside Safety ◽  
Impact Performance ◽  
Crash Testing ◽  
Level 3 ◽  
New Guidelines ◽  
Safety Features ◽  
The Impact ◽  
Crash Tests

The ET-2000 is one of the end treatments currently approved for use with W-beam guardrail systems. The ET-2000 has successfully met all evaluation criteria set forth in NCHRP Report 230. However, with the adoption of NCHRP Report 350 by FHWA as the official guidelines for crash testing of roadside safety features, it became necessary to reevaluate the ET-2000 to the new guidelines. It is noted that one of the design test vehicles specified in NCHRP Report 230, the 2044-kg passenger car, was replaced by a 2000-kg pickup truck (2000P) under NCHRP Report 350 guidelines. The purpose of the crash tests was to evaluate the ET-2000 according to NCHRP Report 350 guidelines. The ET-2000 met NCHRP Report 350 criteria for Performance Level 3 without any design modifications. All findings in this study demonstrate that the impact performance of the ET-2000 was satisfactory.

Crash Testing and Evaluation of Work Zone Barricades

1998 ◽  
Vol 1650 (1) ◽  
pp. 36-44 ◽  
Author(s):  
Roger P. Bligh ◽  
King K. Mak ◽  
Lewis R. Rhodes
Keyword(s):  
Traffic Control ◽  
Work Zone ◽  
Department Of Transportation ◽  
Work Zones ◽  
Impact Performance ◽  
Crash Testing ◽  
Texas Department ◽  
Control Devices ◽  
Traffic Control Devices ◽  
The Impact

Proper traffic control and delineation are critical to achieving safety in work zones. However, the work zone traffic control devices themselves may pose a safety hazard to vehicle occupants or work crews when impacted by errant vehicles. Thus, there was a need to research the safety performance of work zone traffic control devices to ensure that they perform satisfactorily and meet NCHRP Report 350 guidelines. Several research studies sponsored by the Texas Department of Transportation evaluated the impact performance of various work zone traffic control devices, such as temporary and portable sign supports, plastic drums, sign substrates for use with plastic drums, traffic cones, and vertical panels. Specifically addressed are the studies on barricades. Standard wooden barricade construction was found to be unacceptable due to a demonstrated potential for intrusion of fractured members into the occupant compartment. In response to deficiencies identified in the wooden barricade tests, several alternate barricade designs were developed and successfully tested.

scholarly journals Morphological, thermal and mechanical properties of recycled HDPE foams via rotational molding

2021 ◽  
pp. 0021955X2110137
Author(s):  
Yao Dou ◽  
Denis Rodrigue
Keyword(s):  
Cell Density ◽  
Morphological Analysis ◽  
Mechanical Characterization ◽  
Gradual Increase ◽  
Thermal And Mechanical Properties ◽  
Rotational Molding ◽  
Average Cell Size ◽  
Average Cell ◽  
The Impact ◽  
Recycled Hdpe

In this study, foamed recycled high density polyethylene (rHDPE) parts were produced by rotational molding using different concentration (0 to 1% wt.) of a chemical blowing agent (CBA) based on azodicarbonamide. From the samples produced, a complete morphological, thermal and mechanical characterization was performed. The morphological analysis showed a gradual increase in the average cell size, while the cell density firstly increased and then decreased with increasing CBA content. As expected, increasing the CBA content decreased the foam density as well as the thermal conductivity. Although increasing the CBA content decreased both tensile and flexural properties, the impact strength showed a similar trend as the cell density with an optimum CBA content around 0.1% wt. Finally, neat rHDPE samples were also produced by compression molding. The results showed negligible differences between the rotomolded and compression molded properties indicating that optimal rotomolding conditions were selected. These results confirm the possibility of using 100% recycled polymers to produce rotomolded foam parts.

scholarly journals Impact Resistance of Epoxy Composites Reinforced with Amazon Guaruman Fiber: A Brief Report

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2264
Author(s):  
Raphael H. M. Reis ◽  
Fabio C. Garcia Filho ◽  
Larissa F. Nunes ◽  
Veronica S. Candido ◽  
Alisson C. R. Silva ◽  
...  
Keyword(s):  
Fiber Composite ◽  
Impact Resistance ◽  
Fiber Composites ◽  
Epoxy Composites ◽  
Impact Performance ◽  
Electron Microscopy Analysis ◽  
Ballistic Properties ◽  
Microscopy Analysis ◽  
Izod Impact ◽  
The Impact

Fibers extracted from Amazonian plants that have traditionally been used by local communities to produce simple items such as ropes, nets, and rugs, are now recognized as promising composite reinforcements. This is the case for guaruman (Ischinosiphon körn) fiber, which was recently found to present potential mechanical and ballistic properties as 30 vol% reinforcement of epoxy composites. To complement these properties, Izod impact tests are now communicated in this brief report for similar composites with up to 30 vol% of guaruman fibers. A substantial increase in impact resistance, with over than 20 times the absorbed energy for the 30 vol% guaruman fiber composite, was obtained in comparison to neat epoxy. These results were statistically validated by Weibull analysis, ANOVA, and Tukey’s test. Scanning electron microscopy analysis disclosed the mechanisms responsible for the impact performance of the guaruman fiber composites.

scholarly journals Ultrahigh Ballistic Resistance of Twisted Bilayer Graphene

Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 206
Author(s):  
Qing Peng ◽  
Sheng Peng ◽  
Qiang Cao
Keyword(s):  
Weight Ratio ◽  
High Strength ◽  
Bilayer Graphene ◽  
Energy Propagation ◽  
Dynamic Simulations ◽  
Protective Material ◽  
Impact Performance ◽  
Ballistic Resistance ◽  
Twisted Bilayer Graphene ◽  
The Impact

Graphene is a good candidate for protective material owing to its extremely high stiffness and high strength-to-weight ratio. However, the impact performance of twisted bilayer graphene is still obscure. Herein we have investigated the ballistic resistance capacity of twisted bilayer graphene compared to that of AA-stacked bilayer graphene using molecular dynamic simulations. The energy propagation processes are identical, while the ballistic resistance capacity of the twisted bilayer graphene is almost two times larger than the AA-bilayer graphene. The enhanced capacity of the twisted bilayer graphene is assumed to be caused by the mismatch between the two sheets of graphene, which results in earlier fracture of the first graphene layer and reduces the possibility of penetration.

Investigation on the shaft voltage generation of large synchronous turboalternators

2020 ◽  
Vol 39 (5) ◽  
pp. 1145-1156
Author(s):  
Kevin Darques ◽  
Abdelmounaïm Tounzi ◽  
Yvonnick Le-menach ◽  
Karim Beddek
Keyword(s):  
Finite Element ◽  
Design Methodology ◽  
Short Circuit ◽  
Element Model ◽  
Stator Winding ◽  
Content Type ◽  
Voltage Generation ◽  
The Impact ◽  
Investigation Process ◽  
Circulating Currents

Purpose This paper aims to go deeper on the analysis of the shaft voltage of large turbogenerators. The main interest of this study is the investigation process developed. Design/methodology/approach The analysis of the shaft voltage because of several defects is based on a two-dimensional (2D) finite element modeling. This 2D finite element model is used to determine the shaft voltage because of eccentricities or rotor short-circuit. Findings Dynamic eccentricities and rotor short circuit do not have an inherent impact on the shaft voltage. Circulating currents in the stator winding because of defects impact the shaft voltage. Originality/value The original value of this paper is the investigation process developed. This study proposes to quantify the impact of a smooth stator and then to explore the contribution of the real stator winding on the shaft voltage.

Sign in / Sign up

Export Citation Format

Share Document