scholarly journals Pairing Directional Solar Inputs From Ray Tracing to Solar Receiver/Reactor Heat Transfer Models on Unstructured Meshes: Development and Case Studies

2020 ◽  
Author(s):  
H. Evan Bush ◽  
Andrew J. Schrader ◽  
Peter G. Loutzenhiser
Keyword(s):  
Heat Transfer ◽  
Case Studies ◽  
Ray Tracing ◽  
Three Dimensional ◽  
Transfer Model ◽  
Reactor Model ◽  
Ansys Fluent ◽  
Computational Mesh ◽  
Ray Tracing Model ◽  
Transfer Models

Abstract A novel method for pairing surface irradiation and volumetric absorption from ray tracing to computational heat transfer models is presented. The method is well-suited to directionally and spatially-complex concentrated radiative inputs, such as in solar receivers and reactors. The method employs a generalized algorithm for directly mapping absorbed rays from the ray tracing model to boundary or volumetric source terms in the computational mesh. The algorithm is compatible with unstructured, two and three-dimensional meshes with varying element shapes. To validate the method, four case studies were performed on a directly irradiated, windowed solar thermochemical reactor model. The method was shown to be energy conservative and to preserve spatial variation when mapping rays from a Monte Carlo ray tracing model to the computational heat transfer model in ANSYS Fluent.

scholarly journals Pairing Directional Solar Inputs From Ray Tracing to Solar Receiver/Reactor Heat Transfer Models on Unstructured Meshes: Development and Case Studies

2020 ◽  
Vol 143 (3) ◽  
Author(s):  
H. Evan Bush ◽  
Andrew J. Schrader ◽  
Peter G. Loutzenhiser
Keyword(s):  
Heat Transfer ◽  
Monte Carlo ◽  
Case Studies ◽  
Ray Tracing ◽  
Three Dimensional ◽  
Transfer Model ◽  
Reactor Model ◽  
Ansys Fluent ◽  
Ray Tracing Model ◽  
Transfer Models

Abstract A novel method for pairing surface irradiation and volumetric absorption from Monte Carlo ray tracing to computational heat transfer models is presented. The method is well-suited to directionally and spatially complex concentrated radiative inputs (e.g., solar receivers and reactors). The method employs a generalized algorithm for directly mapping absorbed rays from a Monte Carlo ray tracing model to boundary or volumetric source terms in the computational mesh. The algorithm is compatible with unstructured, two and three-dimensional meshes with varying element shapes. Four case studies were performed on a directly irradiated, windowed solar thermochemical reactor model to validate the method. The method was shown to conserve energy and preserve spatial variation when mapping rays from a Monte Carlo ray tracing model to a computational heat transfer model in ansys fluent.

scholarly journals Numerical Modelling Of Humid Air Flow Around A Porous Body

2015 ◽  
Vol 9 (3) ◽  
pp. 161-166
Author(s):  
Aneta Bohojło-Wiśniewska
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Porous Medium ◽  
Numerical Modelling ◽  
Chinese Cabbage ◽  
Air Flow ◽  
Transfer Model ◽  
Humid Air ◽  
Ansys Fluent ◽  
Complex Heat Transfer

Summary This paper presents an example of humid air flow around a single head of Chinese cabbage under conditions of complex heat transfer. This kind of numerical simulation allows us to create a heat and humidity transfer model between the Chinese cabbage and the flowing humid air. The calculations utilize the heat transfer model in porous medium, which includes the temperature difference between the solid (vegetable tissue) and fluid (air) phases of the porous medium. Modelling and calculations were performed in ANSYS Fluent 14.5 software.

Transient Three-Dimensional Heat Transfer Model of a Solar Thermochemical Reactor for H2O and CO2 Splitting via Nonstoichiometric Ceria Redox Cycling

2013 ◽  
Author(s):  
Justin Lapp ◽  
Wojciech Lipiński
Keyword(s):  
Heat Transfer ◽  
Heat Recovery ◽  
Fuel Efficiency ◽  
Three Dimensional ◽  
Reactor Design ◽  
Heat Transfer Model ◽  
Heat Fluxes ◽  
Transfer Model ◽  
Rotating Cylinders ◽  
Solar Receiver

A transient heat transfer model is developed for a solar reactor prototype for H2O and CO2 splitting via two-step non-stoichiometric ceria cycling. Counter-rotating cylinders of reactive and inert materials cycling between high and low temperature zones permit continuous operation and heat recovery. To guide the reactor design a transient three-dimensional heat transfer model is developed based on transient energy conservation, accounting for conduction, convection, radiation, and chemical reactions. The model domain includes the rotating cylinders, a solar receiver cavity, and insulated reactor body. Radiative heat transfer is analyzed using a combination of the Monte Carlo method, Rosseland diffusion approximation, and the net radiation method. Quasi-steady state distributions of temperatures, heat fluxes, and the non-stoichiometric coefficient are reported. Ceria cycles between temperatures of 1708 K and 1376 K. A heat recovery effectiveness of 28% and solar-to-fuel efficiency of 5.2% are predicted for an unoptimized reactor design.

scholarly journals Fast three-dimensional heat transfer model for computing internal temperatures in the bearing housing of automotive turbochargers

2018 ◽  
Vol 21 (8) ◽  
pp. 1286-1297 ◽  
Author(s):  
Antonio Gil ◽  
Andrés Omar Tiseira ◽  
Luis Miguel García-Cuevas ◽  
Tatiana Rodríguez Usaquén ◽  
Guillaume Mijotte
Keyword(s):  
Heat Transfer ◽  
Coke Formation ◽  
Three Dimensional ◽  
Heat Transfer Model ◽  
Operating Conditions ◽  
Thermal Design ◽  
Working Fluid ◽  
Transfer Model ◽  
Lumped Model ◽  
Bearing System

Each of the elements that make up the turbocharger has been gradually improved. In order to ensure that the system does not experience any mechanical failures or loss of efficiency, it is important to study which engine-operating conditions could produce the highest failing rate. Common failing conditions in turbochargers are mostly achieved due to oil contamination and high temperatures in the bearing system. Thermal management becomes increasingly important for the required engine performance. Therefore, it has become necessary to have accurate temperature and heat transfer models. Most thermal design and analysis codes need data for validation; often the data available fall outside the range of conditions the engine experiences in reality leading to the need to interpolate and extrapolate disproportionately. This article presents a fast three-dimensional heat transfer model for computing internal temperatures in the central housing for non-water cooled turbochargers and its direct validation with experimental data at different engine-operating conditions of speed and load. The presented model allows a detailed study of the temperature rise of the central housing, lubrication channels, and maximum level of temperature at different points of the bearing system of an automotive turbocharger. It will let to evaluate thermal damage done to the system itself and influences on the working fluid temperatures, which leads to oil coke formation that can affect the performance of the engine. Thermal heat transfer properties obtained from this model can be used to feed and improve a radial lumped model of heat transfer that predicts only local internal temperatures. Model validation is illustrated, and finally, the main results are discussed.

Numerical Study on 3D Coupled Heat Transfer of Thrust Chamber with Regenerative Cooling

2011 ◽  
Vol 52-54 ◽  
pp. 1057-1061
Author(s):  
Tao Nie ◽  
Wei Qiang Liu
Keyword(s):  
Heat Transfer ◽  
Optimization Design ◽  
Numerical Study ◽  
Computing Time ◽  
Three Dimensional ◽  
Geometrical Model ◽  
Performance Estimation ◽  
Transfer Model ◽  
Empirical Formulas ◽  
Coupled Heat Transfer

To obtain temperature distribution in regenerative-cooled liquid propellant rocket nozzle quickly and accurately, three-dimensional numerical simulation employed using empirical formulas. A reduced one-dimensional model is employed for the coolant flow and heat transfer, while three dimensional heat transfer model is used to calculate the coupling heat transfer through the wall. The geometrical model is subscale hot-firing chamber. The numerical results agree well with experimental data, while temperature field in nozzle obtained. In terms of computing time and accuracy of results, this method can provide a reference for optimization design and performance estimation.

Heat Transfer in Grinding-Hardening of a Cylindrical Component

2011 ◽  
Vol 325 ◽  
pp. 35-41 ◽  
Author(s):  
Thai Nguyen ◽  
Liang Chi Zhang ◽  
Da Le Sun
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Hardened Layer ◽  
Transfer Model ◽  
Plunge Grinding ◽  
Cylindrical Component ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Grinding Hardening ◽  
Good Agreement

A three-dimensional finite element heat transfer model incorporating a moving heat source was developed to investigate the heat transfer mechanism in grinding-hardening of a cylindrical component. The model was applied to analyze the grinding-hardening of quenchable steel 1045 by two grinding methods, traverse and plunge grinding. It was found that the heat generated can promote the martensitic phase transformation in the ground workpiece. As a result, a hardened layer with a uniform thickness can be produced by traverse grinding. However, the layer thickness generated by plunge grinding varies circumferentially. The results are in good agreement with the experimental observations.

Sign in / Sign up

Export Citation Format

Share Document