Predictions of Cooling From Dirt Purge Holes Along the Tip of a Turbine Blade

2003 ◽  
Author(s):  
E. M. Hohlfeld ◽  
J. R. Christophel ◽  
E. L. Couch ◽  
K. A. Thole
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Film Cooling ◽  
Suction Side ◽  
High Heat ◽  
Blowing Ratio ◽  
High Heat Transfer ◽  
Blade Tip ◽  
Flow Through ◽  
Film Cooling Holes

The clearance gap between the tip of a turbine blade and its associated shroud provides a flow path for leakage from the pressure side of the blade to the suction side. The tip region is one area that experiences high heat transfer and, as such, can be the determining factor for blade life. One method for reducing blade tip heat transfer is to use cooler fluid from the compressor, that exits from relatively large dirt purge holes placed in the tip, for cooling purposes. Dirt purge holes are typically manufactured in the blade tip to extract dirt from the coolant flow through centrifugal forces such that these dirt particles do not block smaller diameter film-cooling holes. This paper discusses the results of numerous computational simulations of cooling injection from dirt purge holes along the tip of a turbine blade. Some comparisons are also made to experimental results in which a properly scaled-up blade geometry (12X) was used to form a two-passage linear cascade. Computational results indicate that the cooling achieved through the dirt purge injection from the blade tip is dependent on the gap size as well as the blowing ratio. For a small tip gap (0.54% of the span) the flow exiting the dirt purge holes act as a blockage for the leakage flow across the gap. As the blowing ratio is increased for a large tip gap (1.63% of the span), the tip cooling increases only slightly while the cooling to the shroud increases significantly.

Turbine Blade Tip Film Cooling With Blade Rotation: Part I — Tip and Pressure Side Coolant Injection

2015 ◽  
Author(s):  
Onieluan Tamunobere ◽  
Sumanta Acharya
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Suction Side ◽  
High Heat ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
High Heat Transfer ◽  
Blade Tip

This is the first in a two-part series of an experimental film cooling study conducted on the tip of a turbine blade with a blade rotation speed of 1200 RPM. In this part of the study, the coolant is injected from the blade tip and pressure side (PS) holes, and the effect of the blowing ratio on the heat transfer coefficient and film cooling effectiveness of the blade tip is investigated. The blade has a tip clearance of 1.7% of the blade span and consists of a cut back squealer rim, two cylindrical tip holes and six shaped pressure side holes. The stator-rotor-stator test section is housed in a closed loop wind tunnel that allows for the performance of transient heat transfer tests. Measurements of the heat transfer coefficient and film cooling effectiveness are done on the blade tip using liquid crystal thermography. These measurements are reported for the no coolant case and for blowing ratios of 1.0, 1.5, 2.0, 3.0 and 4.0. The heat transfer results for the no coolant injection show a region of high heat transfer on the blade tip near the blade leading edge region as the incident flow impinges on that region. This region of high heat transfer extends and stretches on the tip as more coolant is introduced through the tip holes at higher blowing ratios. The cooling results show that increasing the blowing ratio increases the film cooling effectiveness. The tip film cooling profile is such that the tip coolant is pushed towards the blade suction side thereby providing better coverage in that region. The shift in coolant flow profile towards the blade suction side as opposed to the pressure side in stationary studies can primarily be attributed to the effects of the blade relative motion.

Turbine Blade Tip Film Cooling With Blade Rotation—Part I: Tip and Pressure Side Coolant Injection

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Onieluan Tamunobere ◽  
Sumanta Acharya
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Suction Side ◽  
High Heat ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
High Heat Transfer ◽  
Blade Tip ◽  
The Heat Transfer Coefficient

An experimental study of film cooling is conducted on the tip of a turbine blade with a blade rotation speed of 1200 rpm. The coolant is injected from the blade tip and pressure side (PS) holes, and the effect of the blowing ratio on the heat transfer coefficient and film cooling effectiveness of the blade tip is investigated. The blade has a tip clearance of 1.7% of the blade span and consists of a cut back squealer rim, two cylindrical tip holes, and six shaped PS holes. The stator–rotor–stator test section is housed in a closed loop wind tunnel that allows for the performance of transient heat transfer tests. Measurements of the heat transfer coefficient and film cooling effectiveness are done on the blade tip using liquid crystal thermography. These measurements are reported for the no coolant case and for blowing ratios of 1.0, 1.5, 2.0, 3.0, and 4.0. The heat transfer result for the no coolant injection shows a region of high heat transfer on the blade tip near the blade leading edge region as the incident flow impinges on that region. This region of high heat transfer extends and stretches on the tip as more coolant is introduced through the tip holes at higher blowing ratios. The cooling results show that increasing the blowing ratio increases the film cooling effectiveness. The cooling effectiveness signatures indicate that the tip coolant is pushed toward the blade suction side thereby providing better coverage in that region. This shift in coolant flow toward the blade suction side, as opposed to the PS in stationary studies, can primarily be attributed to the effects of the blade relative motion.

Heat Transfer and Effectiveness on the Film Cooled Tip and Inner Rim Surfaces of a Turbine Blade

2010 ◽  
Author(s):  
Jun Su Park ◽  
Dong Hyun Lee ◽  
Hyung Hee Cho ◽  
Dong-Ho Rhee ◽  
Shin-Hyung Kang
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Leading Edge ◽  
Suction Side ◽  
High Heat ◽  
Chord Length ◽  
Tip Clearance ◽  
Film Cooling Effectiveness ◽  
High Heat Transfer ◽  
Film Cooling Holes

Detailed heat/mass transfer coefficients and film-cooling effectiveness were measured on the tip and inner rim surfaces of a rotor blade with a squealer rim. The blade was a two-dimensional version of a modern first-stage gas turbine rotor blade with a squealer rim. The experimental apparatus was equipped with a linear cascade of three blades, the axial chord length (Cx) of which was 237 mm with a turning angle of 126°. The mainstream Reynolds number based on the axial chord was 1.5×105. The turbulence intensity level at the cascade inlet was approximately 12%. Measurements were made at three different rim heights (H) of about 3%, 6%, and 9% of the axial chord length. The tip clearance (C) ranges were 1–3% of the axial chord length. Also, three different types of blade tip surfaces were equipped with a single row of film-cooling holes along the camber line, near the pressure and the suction side rim. In particular, a coolant was injected at an incline of 45° from near the suction side film cooling holes. The film cooling experiments were done with a fixed tip clearance and rim height at 1% and 6% of the axial chord length. The blowing rate was fixed at 1.5. High heat transfer rates were observed near the leading edge on the tip surface in some cases, due to the reattachment of tip leakage flow. The peak values moved toward the suction-side edge, and the magnitude and area of high heat transfer increased near the leading edge as the tip clearance increased. The heat transfer decreased on the tip surface with increases in the rim height. In the film-cooling cases, the high heat transfer and film-cooling effectiveness region appeared near the film-cooling holes.

Influence of tip clearance and cavity depth on heat transfer in a cutback squealer tip

2020 ◽  
pp. 095441002096469
Author(s):  
Weijie Wang ◽  
Shaopeng Lu ◽  
Hongmei Jiang ◽  
Qiusheng Deng ◽  
Jinfang Teng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Suction Side ◽  
High Heat ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Trailing Edge ◽  
Cavity Depth ◽  
High Heat Transfer ◽  
Blade Tip ◽  
High Heat Transfer Coefficient

Numerical simulations are conducted to present the aerothermal performance of a turbine blade tip with cutback squealer rim. Two different tip clearance heights (0.5%, 1.0% of the blade span) and three different cavity depths (2.0%, 3.0%, and 6.0% of the blade span) are investigated. The results show that a high heat transfer coefficient (HTC) strip on the cavity floor appears near the suction side. It extends with the increase of tip clearance height and moves towards the suction side with the increase of cavity depth. The cutback region near the trailing edge has a high HTC value due to the flush of over-tip leakage flow. High HTC region shrinks to the trailing edge with the increase of cavity depth since there is more accumulated flow in the cavity for larger cavity depth. For small tip clearance cases, high HTC distribution appears on the pressure side rim. However, high HTC distribution is observed on suction side rim for large tip clearance height. This is mainly caused by the flow separation and reattachment on the squealer rims.

Numerical Study of Heat Transfer and Cooling Effectiveness on a Flat-Tip Turbine Blade

2013 ◽  
Author(s):  
Qihe Huang ◽  
Jiao Wang ◽  
Lei He ◽  
Qiang Xu
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Film Cooling ◽  
Numerical Study ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Cooling Effectiveness ◽  
Blowing Ratio ◽  
Flow And Heat Transfer ◽  
Blade Tip

A numerical study is performed to simulate the tip leakage flow and heat transfer on the first stage rotor blade tip of GE-E3 turbine, which represents a modern gas turbine blade geometry. Calculations consist of the flat blade tip without and with film cooling. For the flat tip without film cooling case, in order to investigate the effect of tip gap clearance on the leakage flow and heat transfer on the blade tip, three different tip gap clearances of 1.0%, 1.5% and 2.5% of the blade span are considered. And to assess the performance of the turbulence models in correctly predicting the blade tip heat transfer, the simulations have been performed by using four different models (the standard k-ε, the RNG k-ε, the standard k-ω and the SST models), and the comparison shows that the standard k-ω model provides the best results. All the calculations of the flat tip without film cooling have been compared and validated with the experimental data of Azad[1] and the predictions of Yang[2]. For the flat tip with film cooling case, three different blowing ratio (M = 0.5, 1.0, and 1.5) have been studied to the influence on the leakage flow in tip gap and the cooling effectiveness on the blade tip. Tip film cooling can largely reduce the overall heat transfer on the tip. And the blowing ratio M = 1.0, the cooling effect for the blade tip is the best.

An Experimental Investigation of Flow Characteristics Downstream of Discrete Film Cooling Holes on Turbine Blade Leading Edge

2011 ◽  
Vol 383-390 ◽  
pp. 5553-5560
Author(s):  
Shao Hua Li ◽  
Hong Wei Qu ◽  
Mei Li Wang ◽  
Ting Ting Guo
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Suction Side ◽  
Wall Region ◽  
Pressure Side ◽  
Blowing Ratio ◽  
Curvature Gradient ◽  
Film Cooling Holes

The gas turbine blade was studied on the condition that the mainstream velocity was 10m/s and the Renolds number based on the chord length of the blade was 160000.The Hot-film anemometer was used to measure the two-dimension speed distribution along the downstream of the film cooling holes on the suction side and the pressure side. The conclusions are as follows: When the blowing ratio of the suction side and the pressure side increasing, the the mainstream and the jet injection mixing center raising. Entrainment flow occurs at the position where the blade surface with great curvature gradient, simultaneously the mixing flow has a wicked adhere to the wall. The velocity gradient of the u direction that on the suction side increase obviously, also the level of the wall adherence is better than the pressure side. With the x/d increasing, the velocity u that on the pressure side gradually become irregularly, also the secondary flow emerged near the wall region where the curvature is great. The blowing ratio on the suction side has a little influence on velocity v than that on the pressure side.

Effect of Shelf Squealer Tip Configurations on Film Cooling Effectiveness

2018 ◽  
Author(s):  
JeongJu Kim ◽  
Wonjik Seo ◽  
Minho Bang ◽  
Seon Ho Kim ◽  
Seok Min Choi ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Linear Cascade ◽  
Blowing Ratio ◽  
Blade Tip ◽  
Film Cooling Holes ◽  
Better Than

Film cooling effectiveness and heat transfer were measured in squealer tip configurations on the blade tip surface. Three different shelf squealer tip geometries were studied: conventional, vertical, and inclined. The experiment was carried out in a wind tunnel with an inlet mainstream Reynolds number, based on the axial chord length of the blade, of 140,000. The experiments were conducted in five blades in linear cascade with an averaged turbulence intensity of 8.5%. The film cooling effectiveness and heat transfer coefficient on the tip surface were obtained using the transient IR thermography technique. For the pressure side film cooling holes, averaging blowing ratios (M) of 1.0 and 2.0 were set. The results showed the film cooling effectiveness distributions on the tip surface. Owing to the mainstream, the cooling effect appeared after x/Cx = 0.15 and the film cooling effectiveness tended to increase toward downstream of the trailing edge. Additionally, the heat transfer distributions were investigated regarding the film cooling holes. In the presence of film cooling holes, the heat transfer distribution had more uniformity than without them on the pressure side. As the blowing ratio increased from 1 to 2, the heat transfer was decreased on the tip surface. The heat transfer ratio represented the change of heat transfer distribution with and without film cooling holes. Those of results were compared in three squealer tip geometries. The overall area-averaged net heat flux reduction (NHFR) levels on the tip surface were enhanced as the blowing ratio increased. The NHFR of the shelf squealer tip configurations was better than that with the conventional squealer tip.

Influence of Different Rim Widths and Blowing Ratios on Film Cooling Characteristics for a Blade Tip

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Jin Wang ◽  
Bengt Sundén ◽  
Min Zeng ◽  
Qiu-wang Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulations ◽  
Film Cooling ◽  
Three Dimensional ◽  
Suction Side ◽  
Leakage Flow ◽  
Pressure Side ◽  
Tip Leakage Flow ◽  
Blade Tip ◽  
Film Cooling Holes

Three-dimensional simulations of the squealer tip on the GE-E3 blade with eight film cooling holes were carried out. The effect of the rim width and the blowing ratio on the blade tip flow and cooling performance were revealed. Numerical simulations were performed to predict the leakage flow and the tip heat transfer with the k–ɛ model. For the squealer tip, the depth of the cavity is fixed but the rim width varies to form a wide cavity, which can decrease the coolant momentum and the tip leakage flow velocity. This cavity contributes to the improvement of the cooling effect in the tip zone. To investigate the influence on the tip heat transfer by the rim width, numerical simulations were performed as a two-part study: (1) unequal rim width study on the pressure side and the suction side and (2) equal rim width study with rim widths of 0.58%, 1.16%, and 1.74% of the axial chord (0.5 mm, 1 mm, and 1.5 mm, respectively) on both the pressure side rim and the suction side rim. With different rim widths, the effect of different global blowing ratios, i.e., M = 0.5, 1.0 and 1.5, was investigated. It is found that the total heat transfer rate is increasing and the heat transfer rates on the rim surface (RS) rapidly ascend with increasing rim width.

Turbine Blade Tip Film-Cooling and Heat Transfer Measurements at High Blowing Ratios

2014 ◽  
Author(s):  
Diganta Narzary ◽  
Kevin Liu ◽  
Je-Chin Han ◽  
Shantanu Mhetras ◽  
Kenneth Landis
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Side Rail ◽  
Blade Tip ◽  
Film Cooling Holes

Film-cooling and heat transfer characteristics of a gas turbine blade tip with a suction side rail was investigated in a stationary 3-blade rectilinear cascade. Mounted at the end of a blow-down facility the cascade operated at inlet and exit Mach numbers of 0.29 and 0.75, respectively. The rail was marginally offset from the suction side edge of the tip and extended from the leading to the trailing edge. A total of 17 film-cooling holes were placed along the near-tip pressure side surface and 3 on the near-tip leading edge surface with the objective of providing coolant to the tip. The tip surface itself did not carry any film-cooling holes. Relatively high blowing ratios of 2.0, 3.0, 4.0, and 4.5 and three tip gaps of 0.87%, 1.6%, and 2.3% of blade span made up the test matrix. Pressure sensitive paint (PSP) and Thermo-Chromic Liquid Crystal (TLC) were the experimental techniques employed to measure film-cooling effectiveness and heat transfer coefficient, respectively. Results indicated that when the tip gap was increased, film-cooling effectiveness on the tip surface decreased and heat transfer to the tip surface increased. On the other hand, when the blowing ratio was increased, film effectiveness increased but the effect on heat transfer coefficient was relatively small. The highest heat transfer coefficient levels were found atop the suction side rail, especially in the downstream two-thirds of its length whereas the lowest levels were found on the tip floor in the widest section of the blade.

Effect of a Cutback Squealer and Cavity Depth on Film-Cooling Effectiveness on a Gas Turbine Blade Tip

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
Shantanu Mhetras ◽  
Diganta Narzary ◽  
Zhihong Gao ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Suction Side ◽  
Pressure Side ◽  
Trailing Edge ◽  
Cavity Depth ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Blade Tip ◽  
Film Cooling Holes

Film-cooling effectiveness from shaped holes on the near tip pressure side and cylindrical holes on the squealer cavity floor is investigated. The pressure side squealer rim wall is cut near the trailing edge to allow the accumulated coolant in the cavity to escape and cool the tip trailing edge. Effects of varying blowing ratios and squealer cavity depth are also examined on film-cooling effectiveness. The film-cooling effectiveness distributions are measured on the blade tip, near tip pressure side and the inner pressure side and suction side rim walls using pressure sensitive paint technique. The internal coolant-supply passages of the squealer tipped blade are modeled similar to those in the GE-E3 rotor blade with two separate serpentine loops supplying coolant to the film-cooling holes. Two rows of cylindrical film-cooling holes are arranged offset to the suction side profile and along the camber line on the tip. Another row of shaped film-cooling holes is arranged along the pressure side just below the tip. The average blowing ratio of the cooling gas is controlled to be 0.5, 1.0, 1.5, and 2.0. A five-bladed linear cascade in a blow down facility with a tip gap clearance of 1.5% is used to perform the experiments. The free-stream Reynolds number, based on the axial chord length and the exit velocity, was 1,480,000 and the inlet and exit Mach numbers were 0.23 and 0.65, respectively. A blowing ratio of 1.0 is found to give best results on the pressure side, whereas the tip surfaces forming the squealer cavity give best results for M=2. Results show high film-cooling effectiveness magnitudes near the trailing edge of the blade tip due to coolant accumulation from upstream holes in the tip cavity. A squealer depth with a recess of 2.1mm causes the average effectiveness magnitudes to decrease slightly as compared to a squealer depth of 4.2mm.

Sign in / Sign up

Export Citation Format

Share Document