Influence of tip clearance and cavity depth on heat transfer in a cutback squealer tip

2020 ◽  
pp. 095441002096469
Author(s):  
Weijie Wang ◽  
Shaopeng Lu ◽  
Hongmei Jiang ◽  
Qiusheng Deng ◽  
Jinfang Teng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Suction Side ◽  
High Heat ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Trailing Edge ◽  
Cavity Depth ◽  
High Heat Transfer ◽  
Blade Tip ◽  
High Heat Transfer Coefficient

Numerical simulations are conducted to present the aerothermal performance of a turbine blade tip with cutback squealer rim. Two different tip clearance heights (0.5%, 1.0% of the blade span) and three different cavity depths (2.0%, 3.0%, and 6.0% of the blade span) are investigated. The results show that a high heat transfer coefficient (HTC) strip on the cavity floor appears near the suction side. It extends with the increase of tip clearance height and moves towards the suction side with the increase of cavity depth. The cutback region near the trailing edge has a high HTC value due to the flush of over-tip leakage flow. High HTC region shrinks to the trailing edge with the increase of cavity depth since there is more accumulated flow in the cavity for larger cavity depth. For small tip clearance cases, high HTC distribution appears on the pressure side rim. However, high HTC distribution is observed on suction side rim for large tip clearance height. This is mainly caused by the flow separation and reattachment on the squealer rims.

scholarly journals Effects of Tip Clearance and Casing Recess on Heat Transfer and Stage Efficiency in Axial Turbines

1998 ◽  
Author(s):  
A. A. Ameri ◽  
E. Steinthorsson ◽  
David L. Rigby
Keyword(s):  
Heat Transfer ◽  
Suction Side ◽  
Tip Clearance ◽  
Flow Conditions ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Blade Tip ◽  
Axial Turbines ◽  
Gap Height ◽  
Stage Efficiency

Calculations were performed to assess the effect of the tip leakage flow on the rate of heat transfer to blade, blade tip and casing. The effect on exit angle and efficiency was also examined. Passage geometries with and without casing recess were considered. The geometry and the flow conditions of the GE-E3 first stage turbine, which represents a modern gas turbine blade were used for the analysis. Clearance heights of 0%, 1%, 1.5% and 3% of the passage height were considered. For the two largest clearance heights considered, different recess depths were studied. There was an increase in the thermal load on all the heat transfer surfaces considered due to enlargement of the clearance gap. Introduction of recessed casing resulted in a drop in the rate of heat transfer on the pressure side but the picture on the suction side was found to be more complex for the smaller tip clearance height considered. For the larger tip clearance height the effect of casing recess was an orderly reduction in the suction side heat transfer as the casing recess height was increased. There was a marked reduction of heat load and peak values on the blade tip upon introduction of casing recess, however only a small reduction was observed on the casing itself. It was reconfirmed that there is a linear relationship between the efficiency and the tip gap height. It was also observed that the recess casing has a small effect on the efficiency but can have a moderating effect on the flow underturning at smaller tip clearances.

Predictions of Cooling From Dirt Purge Holes Along the Tip of a Turbine Blade

2003 ◽  
Author(s):  
E. M. Hohlfeld ◽  
J. R. Christophel ◽  
E. L. Couch ◽  
K. A. Thole
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Film Cooling ◽  
Suction Side ◽  
High Heat ◽  
Blowing Ratio ◽  
High Heat Transfer ◽  
Blade Tip ◽  
Flow Through ◽  
Film Cooling Holes

The clearance gap between the tip of a turbine blade and its associated shroud provides a flow path for leakage from the pressure side of the blade to the suction side. The tip region is one area that experiences high heat transfer and, as such, can be the determining factor for blade life. One method for reducing blade tip heat transfer is to use cooler fluid from the compressor, that exits from relatively large dirt purge holes placed in the tip, for cooling purposes. Dirt purge holes are typically manufactured in the blade tip to extract dirt from the coolant flow through centrifugal forces such that these dirt particles do not block smaller diameter film-cooling holes. This paper discusses the results of numerous computational simulations of cooling injection from dirt purge holes along the tip of a turbine blade. Some comparisons are also made to experimental results in which a properly scaled-up blade geometry (12X) was used to form a two-passage linear cascade. Computational results indicate that the cooling achieved through the dirt purge injection from the blade tip is dependent on the gap size as well as the blowing ratio. For a small tip gap (0.54% of the span) the flow exiting the dirt purge holes act as a blockage for the leakage flow across the gap. As the blowing ratio is increased for a large tip gap (1.63% of the span), the tip cooling increases only slightly while the cooling to the shroud increases significantly.

Heat Transfer and Effectiveness on the Film Cooled Tip and Inner Rim Surfaces of a Turbine Blade

2010 ◽  
Author(s):  
Jun Su Park ◽  
Dong Hyun Lee ◽  
Hyung Hee Cho ◽  
Dong-Ho Rhee ◽  
Shin-Hyung Kang
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Leading Edge ◽  
Suction Side ◽  
High Heat ◽  
Chord Length ◽  
Tip Clearance ◽  
Film Cooling Effectiveness ◽  
High Heat Transfer ◽  
Film Cooling Holes

Detailed heat/mass transfer coefficients and film-cooling effectiveness were measured on the tip and inner rim surfaces of a rotor blade with a squealer rim. The blade was a two-dimensional version of a modern first-stage gas turbine rotor blade with a squealer rim. The experimental apparatus was equipped with a linear cascade of three blades, the axial chord length (Cx) of which was 237 mm with a turning angle of 126°. The mainstream Reynolds number based on the axial chord was 1.5×105. The turbulence intensity level at the cascade inlet was approximately 12%. Measurements were made at three different rim heights (H) of about 3%, 6%, and 9% of the axial chord length. The tip clearance (C) ranges were 1–3% of the axial chord length. Also, three different types of blade tip surfaces were equipped with a single row of film-cooling holes along the camber line, near the pressure and the suction side rim. In particular, a coolant was injected at an incline of 45° from near the suction side film cooling holes. The film cooling experiments were done with a fixed tip clearance and rim height at 1% and 6% of the axial chord length. The blowing rate was fixed at 1.5. High heat transfer rates were observed near the leading edge on the tip surface in some cases, due to the reattachment of tip leakage flow. The peak values moved toward the suction-side edge, and the magnitude and area of high heat transfer increased near the leading edge as the tip clearance increased. The heat transfer decreased on the tip surface with increases in the rim height. In the film-cooling cases, the high heat transfer and film-cooling effectiveness region appeared near the film-cooling holes.

Turbine Blade Tip Film Cooling With Blade Rotation: Part I — Tip and Pressure Side Coolant Injection

2015 ◽  
Author(s):  
Onieluan Tamunobere ◽  
Sumanta Acharya
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Suction Side ◽  
High Heat ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
High Heat Transfer ◽  
Blade Tip

This is the first in a two-part series of an experimental film cooling study conducted on the tip of a turbine blade with a blade rotation speed of 1200 RPM. In this part of the study, the coolant is injected from the blade tip and pressure side (PS) holes, and the effect of the blowing ratio on the heat transfer coefficient and film cooling effectiveness of the blade tip is investigated. The blade has a tip clearance of 1.7% of the blade span and consists of a cut back squealer rim, two cylindrical tip holes and six shaped pressure side holes. The stator-rotor-stator test section is housed in a closed loop wind tunnel that allows for the performance of transient heat transfer tests. Measurements of the heat transfer coefficient and film cooling effectiveness are done on the blade tip using liquid crystal thermography. These measurements are reported for the no coolant case and for blowing ratios of 1.0, 1.5, 2.0, 3.0 and 4.0. The heat transfer results for the no coolant injection show a region of high heat transfer on the blade tip near the blade leading edge region as the incident flow impinges on that region. This region of high heat transfer extends and stretches on the tip as more coolant is introduced through the tip holes at higher blowing ratios. The cooling results show that increasing the blowing ratio increases the film cooling effectiveness. The tip film cooling profile is such that the tip coolant is pushed towards the blade suction side thereby providing better coverage in that region. The shift in coolant flow profile towards the blade suction side as opposed to the pressure side in stationary studies can primarily be attributed to the effects of the blade relative motion.

Effects of Tip Clearance and Casing Recess on Heat Transfer and Stage Efficency in Axial Turbines

1999 ◽  
Vol 121 (4) ◽  
pp. 683-693 ◽  
Author(s):  
A. A. Ameri ◽  
E. Steinthorsson ◽  
D. L. Rigby
Keyword(s):  
Heat Transfer ◽  
Suction Side ◽  
Tip Clearance ◽  
Flow Conditions ◽  
Tip Leakage Flow ◽  
Small Reduction ◽  
Tip Leakage ◽  
Blade Tip ◽  
Axial Turbines ◽  
Gap Height

Calculations were performed to assess the effect of the tip leakage flow on the rate of heat transfer to blade, blade tip, and casing. The effect on exit angle and efficiency was also examined. Passage geometries with and without casing recess were considered. The geometry and the flow conditions of the GE-E3 first-stage turbine, which represents a modern gas turbine blade, were used for the analysis. Clearance heights of 0, 1, 1.5, and 3 percent of the passage height were considered. For the two largest clearance heights considered, different recess depths were studied. There was an increase in the thermal load on all the heat transfer surfaces considered due to enlargement of the clearance gap. Introduction of recessed casing resulted in a drop in the rate of heat transfer on the pressure side, but the picture on the suction side was found to be more complex for the smaller tip clearance height considered. For the larger tip clearance height, the effect of casing recess was an orderly reduction in the suction side heat transfer as the casing recess height was increased. There was a marked reduction of heat load and peak values on the blade tip upon introduction of casing recess; however, only a small reduction was observed on the casing itself. It was reconfirmed that there is a linear relationship between the efficiency and the tip gap height. It was also observed that the recess casing has a small effect on the efficiency but can have a moderating effect on the flow underturning at smaller tip clearances.

Turbine Blade Tip Film Cooling With Blade Rotation—Part I: Tip and Pressure Side Coolant Injection

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Onieluan Tamunobere ◽  
Sumanta Acharya
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Suction Side ◽  
High Heat ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
High Heat Transfer ◽  
Blade Tip ◽  
The Heat Transfer Coefficient

An experimental study of film cooling is conducted on the tip of a turbine blade with a blade rotation speed of 1200 rpm. The coolant is injected from the blade tip and pressure side (PS) holes, and the effect of the blowing ratio on the heat transfer coefficient and film cooling effectiveness of the blade tip is investigated. The blade has a tip clearance of 1.7% of the blade span and consists of a cut back squealer rim, two cylindrical tip holes, and six shaped PS holes. The stator–rotor–stator test section is housed in a closed loop wind tunnel that allows for the performance of transient heat transfer tests. Measurements of the heat transfer coefficient and film cooling effectiveness are done on the blade tip using liquid crystal thermography. These measurements are reported for the no coolant case and for blowing ratios of 1.0, 1.5, 2.0, 3.0, and 4.0. The heat transfer result for the no coolant injection shows a region of high heat transfer on the blade tip near the blade leading edge region as the incident flow impinges on that region. This region of high heat transfer extends and stretches on the tip as more coolant is introduced through the tip holes at higher blowing ratios. The cooling results show that increasing the blowing ratio increases the film cooling effectiveness. The cooling effectiveness signatures indicate that the tip coolant is pushed toward the blade suction side thereby providing better coverage in that region. This shift in coolant flow toward the blade suction side, as opposed to the PS in stationary studies, can primarily be attributed to the effects of the blade relative motion.

Numerical Study of Blade Tip Cooling at High Speed With Tip and Pressure-Side Coolant Injections

2018 ◽  
Author(s):  
Zhihua Zhou ◽  
Songtao Wang ◽  
Shaowen Chen
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Suction Side ◽  
Pressure Side ◽  
Tip Leakage Flow ◽  
Film Cooling Effectiveness ◽  
Coolant Injection ◽  
High Heat Transfer ◽  
Blade Tip ◽  
Cavity Floor

The tip clearance between turbine blade and stationary casing leads to the exposure of blade tip to high temperature gas and contributes to a high thermal load in this region. Then it is necessary to perform cooling on the blade tip. Moreover, the tip leakage flow in a high speed brings complex aerothermal conditions to the blade tip. The blade tip film cooling on the transonic squealer tip is investigated in this research. The effects of tip and pressure-side coolant injections on the blade tip heat transfer are discussed. And the influences of total pressure ratio of coolant to main flow and endwall moving on the film cooling are considered. Firstly, the reliability of a commercial CFD code with different turbulence models was first validated by contrasting with the experimental results. The heat flux and isentropic Ma number predicted with the BSL k-ω model shows a better agreement with the test data. Then the mesh independency study was performed. The mesh with tip and pressure-side injection hole is generated by in-house code. For the tip without film cooling at outlet Mach number of 0.96, the squealer tip shows a high heat transfer at front of the tip cavity floor caused by the impingement of tip leakage flow, besides the suction-side rim has high heat transfer coefficient. With the tip coolant injection, the tip coolant is pushed towards the cavity pressure-side and provides better coverage in this region. At the front of cavity floor near suction-side, there is almost no coolant coverage then it shows little cooling effects. The coolant discharges from the tip over the suction-side rim thereby the heat transfer near the trailing edge is less affected by the tip coolant injection. With the pressure-side near tip film cooling, the coolant injection shows high film-cooling effectiveness at low coolant stagnation pressure and lift off blade surface at high coolant stagnation pressure. The endwall motion increases the total heat load of the blade tip by increase heat load at cavity floor and suction-side near tip region and the reduces film-cooling effectiveness.

A Photographic Study of Flow Boiling Stability on a Plain Surface With Tapered Manifold

2015 ◽  
Author(s):  
Ankit Kalani ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
High Speed ◽  
Flow Boiling ◽  
High Heat ◽  
Bubble Nucleation ◽  
High Heat Transfer ◽  
Plain Surface ◽  
High Heat Transfer Coefficient

Flow boiling in microchannels offers many advantages such as high heat transfer coefficient, higher surface area to volume ratio, low coolant inventory, uniform temperature control and compact design. The application of these flow boiling systems has been severely limited due to early critical heat flux (CHF) and flow instability. Recently, a number of studies have focused on variable flow cross-sectional area to augment the thermal performance of microchannels. In a previous work, the open microchannel with manifold (OMM) configuration was experimentally investigated to provide high heat transfer coefficient coupled with high CHF and low pressure drop. In the current work, high speed images of plain surface using tapered manifold are obtained to gain an insight into the nucleating bubble behavior. The mechanism of bubble nucleation, growth and departure are described through high speed images. Formation of dry spots for both tapered and uniform manifold geometry is also discussed.

Heat Transfer and Aerodynamics of Over-Shroud Leakage Flows in a High-Pressure Turbine

2009 ◽  
Author(s):  
Knut Lehmann ◽  
Richard Thomas ◽  
Howard Hodson ◽  
Vassilis Stefanis
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Large Scale ◽  
Suction Side ◽  
Surface Flow ◽  
Tip Clearance ◽  
Flow Visualisation ◽  
Leakage Flow ◽  
High Pressure Turbine ◽  
High Heat Transfer

An experimental study has been conducted to investigate the distribution of the convective heat transfer on the shroud of a high pressure turbine blade in a large scale rotating rig. A continuous thin heater foil technique has been adapted and implemented on the turbine shroud. Thermochromic Liquid Crystals were employed for the surface temperature measurements to derive the experimental heat transfer data. The heat transfer is presented on the shroud top surfaces and the three fins. The experiments were conducted for a variety of Reynolds numbers and flow coefficients. The effects of different inter-shroud gap sizes and reduced fin tip clearance gaps were also investigated. Details of the shroud flow field were obtained using an advanced Ammonia-Diazo surface flow visualisation technique. CFD predictions are compared with the experimental data and used to aid interpretation. Contour maps of the Nusselt number reveal that regions of highest heat transfer are mostly confined to the suction side of the shroud. Peak values exceed the average by as much as 100 percent. It has been found that the interaction between leakage flow through the inter-shroud gaps and the fin tip leakage jets are responsible for this high heat transfer. The inter-shroud gap leakage flow causes a disruption of the boundary layer on the turbine shroud. Furthermore, the development of the large recirculating shroud cavity vortices is severely altered by this leakage flow.

scholarly journals Effects of Tip Clearance Gap and Exit Mach Number on Turbine Blade Tip and Near-Tip Heat Transfer

2013 ◽  
Author(s):  
K. Anto ◽  
S. Xue ◽  
W. F. Ng ◽  
L. J. Zhang ◽  
H. K. Moon
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Turbine Blade ◽  
Leading Edge ◽  
Suction Side ◽  
Tip Clearance ◽  
Pressure Side ◽  
Engine Blade ◽  
Blade Tip ◽  
Exit Mach Number

This study focuses on local heat transfer characteristics on the tip and near-tip regions of a turbine blade with a flat tip, tested under transonic conditions in a stationary, 2-D linear cascade with high freestream turbulence. The experiments were conducted at the Virginia Tech transonic blow-down wind tunnel facility. The effects of tip clearance and exit Mach number on heat transfer distribution were investigated on the tip surface using a transient infrared thermography technique. In addition, thin film gages were used to study similar effects in heat transfer on the near-tip regions at 94% height based on engine blade span of the pressure and suction sides. Surface oil flow visualizations on the blade tip region were carried-out to shed some light on the leakage flow structure. Experiments were performed at three exit Mach numbers of 0.7, 0.85, and 1.05 for two different tip clearances of 0.9% and 1.8% based on turbine blade span. The exit Mach numbers tested correspond to exit Reynolds numbers of 7.6 × 105, 9.0 × 105, and 1.1 × 106 based on blade true chord. The tests were performed with a high freestream turbulence intensity of 12% at the cascade inlet. Results at 0.85 exit Mach showed that an increase in the tip gap clearance from 0.9% to 1.8% translates into a 3% increase in the average heat transfer coefficients on the blade tip surface. At 0.9% tip clearance, an increase in exit Mach number from 0.85 to 1.05 led to a 39% increase in average heat transfer on the tip. High heat transfer was observed on the blade tip surface near the leading edge, and an increase in the tip clearance gap and exit Mach number augmented this near-leading edge tip heat transfer. At 94% of engine blade height on the suction side near the tip, a peak in heat transfer was observed in all test cases at s/C = 0.66, due to the onset of a downstream leakage vortex, originating from the pressure side. An increase in both the tip gap and exit Mach number resulted in an increase, followed by a decrease in the near-tip suction side heat transfer. On the near-tip pressure side, a slight increase in heat transfer was observed with increased tip gap and exit Mach number. In general, the suction side heat transfer is greater than the pressure side heat transfer, as a result of the suction side leakage vortices.

Sign in / Sign up

Export Citation Format

Share Document