Effect of Centrifugal Force on Conventional and Alternative Fuel Surrogate Turbulent Premixed Flames

2014 ◽  
Author(s):  
Alejandro M. Briones ◽  
Balu Sekar ◽  
Timothy Erdmann
Keyword(s):  
Flame Front ◽  
Centrifugal Force ◽  
Flame Propagation ◽  
Propagation Velocity ◽  
Turbulent Flame ◽  
Premixed Flames ◽  
Flame Speed ◽  
Turbulent Premixed Flames ◽  
Flame Propagation Velocity ◽  
Turbulent Flame Speed

The effect of centrifugal force on flame propagation velocity of stoichiometric propane-, kerosene-, and n-octane-air turbulent premixed flames was numerically examined. The quasi-turbulent numerical model was set in an unsteady two-dimensional geometry with finite length in the transverse and streamwise directions but with infinite length in the spanwise direction. There was relatively good comparison between literature-reported measurements and predictions of propane-air flame propagation velocity as a function of centrifugal force. It was found that for all mixtures the flame propagation velocity increases with centrifugal force. It reaches a maximum then falls off rapidly with further increases in centrifugal force. The results of this numerical study suggest there are no distinct differences among the three mixtures in terms of the effect of centrifugal force on the flame propagation velocity. There are, however, quantitative differences. The numerical models are set in a non-inertial, rotating reference frame. This rotation imposes a radially outward (centrifugal) force. The ignited mixture at one end of the tube raises the temperature and its heat release tends to laminarize the flow. The attained density difference combined with the direction of the centrifugal force promotes Rayleigh-Taylor instability. This instability with thermal expansion and turbulent flame speed constitute the flame propagation mechanism towards the other tube end. A wave is also originated but propagates faster than the flame. During propagation the flame interacts with eddies that wrinkle and/or corrugate the flame. The flame front wrinkles interact with streamtubes that enhance Landau-Darrieus (hydrodynamic) instability, giving rise to a corrugated flame. Under strong stretch conditions the stabilizing equidiffusive-curvature mechanism fails and the flame front breaks up, allowing inflow of unburned mixture into the flame. This phenomenon slows down the flame temporarily and then the flame speeds up faster than before. However, if corrugation is large and the inflow of unburned mixture into the flame is excessive, the latter locally quenches and slows down the flame. This occurs when the centrifugal force is large, tending to blowout the flame. The wave in the tube interacts continuously with the flame through baroclinic torques at the flame front that further enhances the above mentioned flame-eddies interactions. Only at low centrifugal forces the wave intermingles several times with the flame before the averaged flame propagation velocity is determined. The centrifugal force does not substantially increase the turbulent flame speed as commented by previous experimental investigations. The results also suggest that an ultra-compact combustor (UCC) with high-g cavity (HGC) will be limited to centrifugal force levels in the 2000–3000g range.

Effect of Centrifugal Force on Turbulent Premixed Flames

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
Alejandro M. Briones ◽  
Balu Sekar ◽  
Timothy Erdmann
Keyword(s):  
Numerical Model ◽  
Flame Front ◽  
Centrifugal Force ◽  
Flame Propagation ◽  
Propagation Velocity ◽  
Turbulent Flame ◽  
Premixed Flames ◽  
Turbulent Premixed Flames ◽  
Flame Propagation Velocity ◽  
Turbulent Flame Speed

The effect of centrifugal force on flame propagation velocity of stoichiometric propane–, kerosene–, and n-octane–air turbulent premixed flames was numerically examined. The quasi-turbulent numerical model was set in an unsteady two-dimensional (2D) geometry with finite length in the transverse and streamwise directions but with infinite length in the spanwise direction. There was relatively good comparison between literature-reported measurements and predictions of propane–air flame propagation velocity as a function of centrifugal force. It was found that for all mixtures the flame propagation velocity increases with centrifugal force. It reaches a maximum, then falls off rapidly with further increases in centrifugal force. The results of this numerical study suggest that there are no distinct differences among the three mixtures in terms of the trends seen of the effect of centrifugal force on the flame propagation velocity. There are, however, quantitative differences. The numerical model is set in a noninertial, rotating reference frame. This rotation imposes a radially outward (centrifugal) force. The ignited mixture at one end of the tube raises the temperature and its heat release tends to laminarize the flow. The attained density difference combined with the direction of the centrifugal force promotes Rayleigh–Taylor instability. This instability with thermal expansion and turbulent flame speed constitute the flame propagation mechanism towards the other tube end. A wave is also generated from the ignition zone but propagates faster than the flame. During propagation the flame interacts with eddies that wrinkle and/or corrugate the flame. The flame front wrinkles interact with streamtubes that enhance Landau–Darrieus (hydrodynamic) instability, giving rise to a corrugated flame. Under strong stretch conditions the stabilizing equidiffusive-curvature mechanism fails and the flame front breaks up, allowing inflow of unburned mixture into the flame. This phenomenon slows down the flame temporarily and then the flame speeds up faster than before. However, if corrugation is large and the inflow of unburned mixture into the flame is excessive, the latter locally quenches and slows down the flame. This occurs when the centrifugal force is large, tending to blowout the flame. The wave in the tube interacts continuously with the flame through baroclinic torques at the flame front that further enhances the above mentioned flame–eddy interactions. Only at low centrifugal forces, the wave intermingles several times with the flame before the averaged flame propagation velocity is determined. The centrifugal force does not substantially increase the turbulent flame speed as commented by previous experimental investigations. The results also suggest that an ultracompact combustor (UCC) with high-g cavity (HGC) will be limited to centrifugal force levels in the 2000–3000 g range.

scholarly journals Effects of pressure gradients on turbulent premixed flames

1997 ◽  
Vol 353 ◽  
pp. 83-114 ◽  
Author(s):  
DENIS VEYNANTE ◽  
THIERRY POINSOT
Keyword(s):  
Pressure Gradient ◽  
Turbulent Transport ◽  
Turbulent Flame ◽  
Premixed Flames ◽  
Flame Speed ◽  
Pressure Gradients ◽  
Turbulent Premixed Flames ◽  
Turbulent Flame Speed ◽  
Flame Brush ◽  
Turbulent Premixed

In most practical situations, turbulent premixed flames are ducted and, accordingly, subjected to externally imposed pressure gradients. These pressure gradients may induce strong modifications of the turbulent flame structure because of buoyancy effects between heavy cold fresh and light hot burnt gases. In the present work, the influence of a constant acceleration, inducing large pressure gradients, on a premixed turbulent flame is studied using direct numerical simulations.A favourable pressure gradient, i.e. a pressure decrease from unburnt to burnt gases, is found to decrease the flame wrinkling, the flame brush thickness, and the turbulent flame speed. It also promotes counter-gradient turbulent transport. On the other hand, adverse pressure gradients tend to increase the flame brush thickness and turbulent flame speed, and promote classical gradient turbulent transport. As proposed by Libby (1989), the turbulent flame speed is modified by a buoyancy term linearly dependent on both the imposed pressure gradient and the integral length scale lt.A simple model for the turbulent flux u″c″ is also proposed, validated from simulation data and compared to existing models. It is shown that turbulent premixed flames can exhibit both gradient and counter-gradient transport and a criterion integrating the effects of pressure gradients is derived to differentiate between these regimes. In fact, counter-gradient diffusion may occur in most practical ducted flames.

Flame Characteristics and Turbulent Flame Speeds of Turbulent, High-Pressure, Lean Premixed Methane/Air Flames

2005 ◽  
Author(s):  
P. Griebel ◽  
R. Bombach ◽  
A. Inauen ◽  
R. Scha¨ren ◽  
S. Schenker ◽  
...  
Keyword(s):  
Flame Front ◽  
Gas Turbines ◽  
Equivalence Ratio ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Operating Conditions ◽  
Turbulent Flame Speed ◽  
Front Position ◽  
Preheating Temperature ◽  
Lean Premixed

The present experimental study focuses on flame characteristics and turbulent flame speeds of lean premixed flames typical for stationary gas turbines. Measurements were performed in a generic combustor at a preheating temperature of 673 K, pressures up to 14.4 bars (absolute), a bulk velocity of 40 m/s, and an equivalence ratio in the range of 0.43–0.56. Turbulence intensities and integral length scales were measured in an isothermal flow field with Particle Image Velocimetry (PIV). The turbulence intensity (u′) and the integral length scale (LT) at the combustor inlet were varied using turbulence grids with different blockage ratios and different hole diameters. The position, shape, and fluctuation of the flame front were characterized by a statistical analysis of Planar Laser Induced Fluorescence images of the OH radical (OH-PLIF). Turbulent flame speeds were calculated and their dependence on operating conditions (p, φ) and turbulence quantities (u′, LT) are discussed and compared to correlations from literature. No influence of pressure on the most probable flame front position or on the turbulent flame speed was observed. As expected, the equivalence ratio had a strong influence on the most probable flame front position, the spatial flame front fluctuation, and the turbulent flame speed. Decreasing the equivalence ratio results in a shift of the flame front position farther downstream due to the lower fuel concentration and the lower adiabatic flame temperature and subsequently lower turbulent flame speed. Flames operated at leaner equivalence ratios show a broader spatial fluctuation as the lean blow-out limit is approached and therefore are more susceptible to flow disturbances. In addition, because of a lower turbulent flame speed these flames stabilize farther downstream in a region with higher velocity fluctuations. This increases the fluctuation of the flame front. Flames with higher turbulence quantities (u′, LT) in the vicinity of the combustor inlet exhibited a shorter length and a higher calculated flame speed. An enhanced turbulent heat and mass transport from the recirculation zone to the flame root location due to an intensified mixing which might increase the preheating temperature or the radical concentration is believed to be the reason for that.

Hydrogen–Air–Steam Deflagration Experiment Simulated Using Different Turbulent Flame-Speed Closure Models

2018 ◽  
Vol 4 (3) ◽  
Author(s):  
Holler Tadej ◽  
Ed M. J. Komen ◽  
Kljenak Ivo
Keyword(s):  
Flame Propagation ◽  
Nuclear Power ◽  
Large Scale ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Energy Output ◽  
Combustion Model ◽  
Turbulent Flame Speed ◽  
Modeling Approach ◽  
Combustion Models

The paper presents the computational fluid dynamics (CFD) combustion modeling approach based on two combustion models. This modeling approach was applied to a hydrogen deflagration experiment conducted in a large-scale confined experimental vessel. The used combustion models were Zimont's turbulent flame-speed closure (TFC) model and Lipatnikov's flame-speed closure (FSC) model. The conducted simulations are aimed to aid identifying and evaluating the potential hydrogen risks in nuclear power plant (NPP) containment. The simulation results show good agreement with experiment for axial flame propagation using the Lipatnikov combustion model. However, substantial overprediction in radial flame propagation is observed using both combustion models, which consequently results also in overprediction of the pressure increase rate and overall combustion energy output. As assumed for a large-scale experiment without any turbulence inducing structures, the combustion took place in low-turbulence regimes, where the Lipatnikov combustion model, due to its inclusion of quasi-laminar source term, has advantage over the Zimont model.

Large-Scale Homogeneous Hydrogen-Air-Steam Deflagration Experiment Simulated Using Two Turbulent Flame Speed Closure Models

2016 ◽  
Author(s):  
Tadej Holler ◽  
Varun Jain ◽  
Ed M. J. Komen ◽  
Ivo Kljenak
Keyword(s):  
Flame Propagation ◽  
Nuclear Power ◽  
Large Scale ◽  
Turbulent Flame ◽  
Turbulent Flames ◽  
Flame Speed ◽  
Energy Output ◽  
Combustion Model ◽  
Turbulent Flame Speed ◽  
Combustion Models

The CFD combustion modeling approach based on two combustion models was applied to a hydrogen deflagration experiment conducted in a large-scale confined experimental vessel. The used combustion models were Zimont’s Turbulent Flames Speed Closure (TFC) model and Lipatnikov’s Flame Speed Closure (FSC) model. The conducted simulations are aimed to aid identifying and evaluating the potential hydrogen risks in Nuclear Power Plant (NPP) containment. The simulation results show good agreement with experiment for axial flame propagation using the Lipatnikov combustion model. However substantial overprediction in radial flame propagation is observed using both combustion models, which consequently results also in overprediction of the pressure increase rate and overall combustion energy output. As assumed for a large-scale experiment without any turbulence inducing structures, the combustion took place in low-turbulence regimes, where the Lipatnikov combustion model, due to its inclusion of quasi-laminar source term, has advantage over the Zimont model.

Measurements of Stretch Statistics at Flame Leading Points for High Hydrogen Content Fuels

2014 ◽  
Author(s):  
Andrew Marshall ◽  
Julia Lundrigan ◽  
Prabhakar Venkateswaran ◽  
Jerry Seitzman ◽  
Tim Lieuwen
Keyword(s):  
Flame Front ◽  
Hydrogen Content ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Fuel Composition ◽  
Mean Flow ◽  
Tangential Strain ◽  
High Hydrogen ◽  
High Hydrogen Content ◽  
Turbulent Flame Speed

Fuel composition has a strong influence on the turbulent flame speed, even at very high turbulence intensities. An important implication of this result is that the turbulent flame speed cannot be extrapolated from one fuel to the next using only the laminar flame speed and turbulence intensity as scaling variables. This paper presents curvature and tangential strain rate statistics of premixed turbulent flames for high hydrogen content fuels. Global (unconditioned) stretch statistics are presented as well as measurements conditioned on the leading points of the flame front. These measurements are motivated by previous experimental and theoretical work that suggests the turbulent flame speed is controlled by the flame front characteristics at these points. The data were acquired with high speed particle image velocimetry (PIV) in a low swirl burner (LSB). We attained measurements for several H2:CO mixtures over a range of mean flow velocities and turbulence intensities. The results show that fuel composition has a systematic, yet weak effect on curvatures and tangential strain rates at the leading points. Instead, stretch statistics at the leading points are more strongly influenced by mean flow velocity and turbulence level. It has been argued that the increased turbulent flame speeds seen with increasing hydrogen content are the result of increasing flame stretch rates, and therefore SL,max values, at the flame leading points. However, the differences observed with changing fuel compositions are not significant enough to support this hypothesis. Additional analysis is needed to understand the physical mechanisms through which the turbulent flame speed is altered by fuel composition effects.

Experimental Study of Flame Stretch Under Engine-Like Conditions

2017 ◽  
Author(s):  
Behdad Afkhami ◽  
Yanyu Wang ◽  
Scott A. Miers ◽  
Jeffrey D. Naber
Keyword(s):  
Flame Front ◽  
Flame Propagation ◽  
High Speed ◽  
Combustion Engine ◽  
Turbulent Flame ◽  
Experimental Studies ◽  
Flame Velocity ◽  
Turbulent Flame Speed ◽  
Stretch Rate ◽  
Flame Stretch

Since fossil fuels will remain the main source of energy for power generation and transportation in next decades, their combustion processes remain an important concern for the foreseeable future. For liquid or gaseous fuels, flame velocity that propagates normal to itself and relative to the flow into the unburned mixture is one of the most important quantities to study. In a non-uniform flow, a curved flame front area changes continually which is known as flame stretch. The concept becomes more important when it is realized that the stretch affects the turbulent flame speed. The current research empirically studies flame stretch under engine-like conditions since there has not been enough experimental studies in this area. For this reason, a one-cylinder, direct-injection, spark-ignition, naturally-aspirated optical engine was utilized to image the flame propagation process inside an internal combustion engine cylinder on the tumble plane. The flame front was found by processing high speed images which were taken from the flame inside the cylinder. Flame front propagation analysis showed that after the flame kernel was developed, during flame propagation period, the stretch rate decreased until the flame front touches the piston surface. This trend was common among stoichiometric, lean, and rich mixtures. In addition, the fuel-air mixture with λ = 0.85 showed lower stretch rate compared to stoichiometric or lean mixture with λ = 1.2. However, based on previous studies, further enrichment may result in the flame stretch rate become greater than that of the stretch rates for stoichiometric or lean mixtures. Also, comparing the stretch rate at two different engine speeds revealed that as the speed increased the stretch rate also increased; especially during the early flame development period. Therefore, according to previous studies which discussed flame stretch as a mechanism for flame extinguishment, the probability of the flame extinction is higher when the engine speed is higher.

Sign in / Sign up

Export Citation Format

Share Document