Experimental and Numerical Study on the Effects of the Relative Position of Film Hole and Orientation Ribs on the Film Cooling With Ribbed Cross-Flow Coolant Channel

2020 ◽  
Author(s):  
Bingran Li ◽  
Cunliang Liu ◽  
Lin Ye ◽  
Huiren Zhu ◽  
Fan Zhang
Keyword(s):  
Heat Transfer ◽  
Relative Position ◽  
Film Cooling ◽  
Numerical Study ◽  
Cross Flow ◽  
Internal Cooling ◽  
Transfer Coefficients ◽  
Cooling Performance ◽  
Heat Transfer Coefficients ◽  
Numerical Studies

Abstract To investigate the application of ribbed cross-flow coolant channels with film hole effusion and the effects of the internal cooling configuration on film cooling, experimental and numerical studies are conducted on the effect of the relative position of the film holes and different orientation ribs on the film cooling performance. Three cases of the relative position of the film holes and different orientation ribs (post-rib, centered, and pre-rib) in two ribbed cross-flow channels (135° and 45° orientation ribs) are investigated. The film cooling performances are measured under three blowing ratios by the transient liquid crystal measurement technique. A RANS simulation with the realizable k-ε turbulence model and enhanced wall treatment is performed. The results show that the cooling effectiveness and the downstream heat transfer coefficient for the 135° rib are basically the same in the three position cases, and the differences between the local effectiveness average values for the three are no more than 0.04. The differences between the heat transfer coefficients are no more than 0.1. The “pre-rib” and “centered” cases are studied for the 45° rib, and the position of the structures has little effect on the film cooling performance. In the different position cases, the outlet velocity distribution of the film holes, the jet pattern and the discharge coefficient are consistent with the variation in the cross flow. The related research previously published by the authors showed that the inclination of the ribs with respect to the holes affects the film cooling performance. This study reveals that the relative positions of the ribs and holes have little effect on the film cooling performance. This paper expands and improves the study of the effect of the internal cooling configuration on film cooling and makes a significant contribution to the design and industrial application of the internal cooling channel of a turbine blade.

Heat Transfer Coefficient Measurements of Film-Cooling Holes With Expanded Exits

1998 ◽  
Author(s):  
M. Gritsch ◽  
A. Schulz ◽  
S. Wittig
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Film Cooling ◽  
Cylindrical Hole ◽  
Superposition Method ◽  
Transfer Coefficients ◽  
Cooling Performance ◽  
Heat Transfer Coefficients ◽  
Film Cooling Holes ◽  
Injection Location

Detailed measurements of heat transfer coefficients in the nearfield of three different film-cooling holes are presented. The hole geometries investigated include a cylindrical hole and two holes with a diffuser shaped exit portion (i.e. a fan-shaped and a laidback fanshaped hole). They were tested over a range of blowing ratios M = 0.25…1.75 at an external crossflow Mach number of 0.6 and a coolant-to-mainflow density ratio of 1.85. Additionally, the effect of the internal coolant supply Mach number is addressed. Temperatures of the diabatic surface downstream of the injection location are measured by means of an infrared camera system. They are used as boundary conditions for a finite element analysis to determine surface heat fluxes and heat transfer coefficients. The superposition method is applied to evaluate the overall film-cooling performance of the hole geometries investigated. As compared to the cylindrical hole, both expanded holes show significantly lower heat transfer coefficients downstream of the injection location, particularly at high blowing ratios. The laidback fanshaped hole provides a better lateral spreading of the injected coolant than the fanshaped hole which leads to lower laterally averaged heat transfer coefficients. Coolant passage crossflow Mach number affects the flowfield of the jet being ejected from the hole and, therefore, has an important impact on film-cooling performance.

Film Cooling From a Row of Holes With Both Ends Embedded in Transverse Slots

2008 ◽  
Author(s):  
D. H. Zhang ◽  
L. Sun ◽  
Q. Y. Chen ◽  
M. Lin ◽  
M. Zeng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Aerodynamic Performance ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Discharge Coefficients ◽  
Cylindrical Holes

Embedding a row of typical cylindrical holes in a transverse slot can improve the cooling performance. Rectangular slots can increase the cooling effectiveness but is at the cost of decreasing of discharge coefficients. An experiment is conducted to examine the effects of an overlying transverse inclined trench on the film cooling performance of axial holes. Four different trench configurations are tested including the baseline inclined cylindrical holes. The influence of the geometry of the upstream lip of the exit trench and the geometry of the inlet trench on cooling performance is examined. Detailed film cooling effectiveness and heat transfer coefficients are obtained separately using the steady state IR thermography technique. The discharge coefficients are also acquired to evaluate the aerodynamic performance of different hole configurations. The results show that the film cooling holes with both ends embedded in slots can provide higher film cooling effectiveness and lower heat transfer coefficients; it also can provide higher discharge coefficients whilst retaining the mechanical strength of a row of discrete holes. The cooling performance and the aerodynamic performance of the holes with both ends embedded in inclined slots are superior to the holes with only exit trenched. To a certain extent, the configuration of the upstream lip of the exit trench affects the cooling performance of the downstream of the trench. The filleting for the film hole inlet avail the improvement of the cooling effect, but not for the film hole outlet. Comparing film cooling with embedded holes to unembedded holes, the overall heat flux ratio shows that the film holes with both ends embedded in slots and filleting for the film hole inlet can produce the highest heat flux reduction.

Experimental and Numerical Study of Heat Transfer in a Gas Turbine Combustor Liner

2003 ◽  
Vol 125 (4) ◽  
pp. 994-1002 ◽  
Author(s):  
J. C. Bailey ◽  
J. Intile ◽  
T. F. Fric ◽  
A. K. Tolpadi ◽  
N. V. Nirmalan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Numerical Study ◽  
Cross Flow ◽  
Turbulence Models ◽  
Flow Distribution ◽  
Transfer Coefficients ◽  
Gas Turbine Combustor ◽  
Heat Transfer Coefficients ◽  
Combustor Liner

Experiments and numerical simulations were conducted to understand the heat transfer characteristics of a stationary gas turbine combustor liner cooled by impingement jets and cross flow between the liner and sleeve. Heat transfer was also aided by trip-strip turbulators on the outside of the liner and in the flowsleeve downstream of the jets. The study was aimed at enhancing heat transfer and prolonging the life of the combustor liner components. The combustor liner and flow sleeve were simulated using a flat-plate rig. The geometry has been scaled from actual combustion geometry except for the curvature. The jet Reynolds number and the mass-velocity ratios between the jet and cross flow in the rig were matched with the corresponding combustor conditions. A steady-state liquid crystal technique was used to measure spatially resolved heat transfer coefficients for the geometric and flow conditions mentioned above. The heat transfer was measured both in the impingement region as well as over the turbulators. A numerical model of the combustor test rig was created that included the impingement holes and the turbulators. Using CFD, the flow distribution within the flow sleeve and the heat transfer coefficients on the liner were both predicted. Calculations were made by varying the turbulence models, numerical schemes, and the geometrical mesh. The results obtained were compared to the experimental data and recommendations have been made with regard to the best modeling approach for such liner-flow sleeve configurations.

Comparison the Cooling Performance of Cylindrical and Fan-Shaped Cooling Holes With Special Emphasis on the Effect of Internal Coolant Cross-Flow

2008 ◽  
Author(s):  
Christian Saumweber ◽  
Achmed Schulz
Keyword(s):  
Film Cooling ◽  
Symmetry Plane ◽  
Cross Flow ◽  
Transfer Coefficients ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Heat Transfer Coefficients ◽  
Expansion Angle ◽  
Cooling Hole

Cooling holes in real gas turbine applications are prevalently exposed to cross-flow in the coolant passage. The majority of the studies available in literature do not consider the effects of flow in the coolant passage. Our own studies however reveal that especially diffuser holes are very susceptible in respect to cross-flow at the hole entrance, if the orientation of the cross-flow is perpendicular to the symmetry plane of the cooling hole. The effect of coolant cross-flow will be discussed in detail. The superordinate target is to identify the dominating mechanisms, which determine the flow field within the diffuser hole and hence limit the potential of cooling performance augmentation. For this reason a fan-shaped hole with 14° expansion angle will be compared to a simple cylindrical hole. Both holes have a length-to-diameter ratio of 6 and an inclination angle of 30°. The comparison will be performed by means of experimentally gained discharge coefficients, local and laterally averaged adiabatic film cooling effectiveness, and heat transfer coefficients. Numerical simulations of the cooling flow will support the interpretation of the experimental results.

Experimental and Numerical Study of Heat Transfer in a Gas Turbine Combustor Liner

2002 ◽  
Author(s):  
Jeremy C. Bailey ◽  
John Intile ◽  
Thomas F. Fric ◽  
Anil K. Tolpadi ◽  
Nirm V. Nirmalan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Numerical Study ◽  
Cross Flow ◽  
Turbulence Models ◽  
Flow Distribution ◽  
Transfer Coefficients ◽  
Gas Turbine Combustor ◽  
Heat Transfer Coefficients ◽  
Combustor Liner

Experiments and numerical simulations were conducted to understand the heat transfer characteristics of a stationary gas turbine combustor liner cooled by impingement jets and cross flow between the liner and sleeve. Heat transfer was also aided by trip-strip turbulators on the outside of the liner and in the flowsleeve downstream of the jets. The study was aimed at enhancing heat transfer and prolonging the life of the combustor liner components. The combustor liner and flow sleeve were simulated using a flat plate rig. The geometry has been scaled from actual combustion geometry except for the curvature. The jet Reynolds number and the mass-velocity ratios between the jet and cross flow in the rig were matched with the corresponding combustor conditions. A steady state liquid crystal technique was used to measure spatially resolved heat transfer coefficients for the geometric and flow conditions mentioned above. The heat transfer was measured both in the impingement region as well as over the turbulators. A numerical model of the combustor test rig was created that included the impingement holes and the turbulators. Using CFD, the flow distribution within the flow sleeve and the heat transfer coefficients on the liner were both predicted. Calculations were made by varying the turbulence models, numerical schemes, and the geometrical mesh. The results obtained were compared to the experimental data and recommendations have been made with regard to the best modeling approach for such liner-flow sleeve configurations.

scholarly journals Numerical Study on Influence of Cross Flow on Rewetting of AHWR Fuel Bundle

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Mithilesh Kumar ◽  
D. Mukhopadhyay ◽  
A. K. Ghosh ◽  
Ravi Kumar
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Cross Flow ◽  
Fluid Temperature ◽  
Initial Surface ◽  
Fuel Temperature ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Fuel Bundle ◽  
Fuel Pin

Numerical study on AHWR fuel bundle has been carried out to assess influence of circumferential and cross flow rewetting on the conduction heat transfer. The AHWR fuel bundle quenching under accident condition is designed primarily with radial jets at several axial locations. A 3D (r,θ,z) transient conduction fuel pin model has been developed to carry out the study with a finite difference method (FDM) technique with alternating direction implicit (ADI) scheme. The single pin has been considered to study effect of circumferential conduction and multipins have been considered to study the influence of cross flow. Both analyses are carried out with the same fluid temperature and heat transfer coefficients as boundary conditions. It has been found from the analyses that, for radial jet, the circumferential conduction is significant and due to influence of overall cross flow the reductions in fuel temperature in the same quench plane in different rings are different with same initial surface temperature. Influence of cross flow on rewetting is found to be very significant. Outer fuel pins rewetting time is higher than inner.

Degradation of Film Cooling Performance on a Turbine Vane Suction Side due to Surface Roughness

2005 ◽  
Vol 128 (3) ◽  
pp. 547-554 ◽  
Author(s):  
James L. Rutledge ◽  
David Robertson ◽  
David G. Bogard
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Film Cooling ◽  
Extended Period ◽  
Suction Side ◽  
Transfer Coefficients ◽  
Cooling Performance ◽  
Heat Transfer Coefficients ◽  
Turbine Vane ◽  
Adiabatic Effectiveness

After an extended period of operation, the surfaces of turbine airfoils become extremely rough due to deposition, spallation, and erosion. The rough airfoil surfaces will cause film cooling performance degradation due to effects on adiabatic effectiveness and heat transfer coefficients. In this study, the individual and combined effects of roughness upstream and downstream of a row of film cooling holes on the suction side of a turbine vane have been determined. Adiabatic effectiveness and heat transfer coefficients were measured for a range of mainstream turbulence levels and with and without showerhead blowing. Using these parameters, the ultimate film cooling performance was quantified in terms of net heat flux reduction. The dominant effect of roughness was a doubling of the heat transfer coefficients. Maximum adiabatic effectiveness levels were also decreased significantly. Relative to a film cooled smooth surface, a film cooled rough surface was found to increase the heat flux to the surface by 30%–70%.

Degradation of Film Cooling Performance on a Turbine Vane Suction Side Due to Surface Roughness

2005 ◽  
Author(s):  
James L. Rutledge ◽  
David Robertson ◽  
David G. Bogard
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Film Cooling ◽  
Extended Period ◽  
Suction Side ◽  
Transfer Coefficients ◽  
Cooling Performance ◽  
Heat Transfer Coefficients ◽  
Turbine Vane ◽  
Adiabatic Effectiveness

After an extended period of operation, the surfaces of turbine airfoils become extremely rough due to deposition, spallation, and erosion. The rough airfoil surfaces will cause film cooling performance degradation due to effects on adiabatic effectiveness and heat transfer coefficients. In this study, the individual and combined effects of roughness upstream and downstream of a row of film cooling holes on the suction side of a turbine vane have been determined. Adiabatic effectiveness and heat transfer coefficients were measured for a range of mainstream turbulence levels and with and without showerhead blowing. Using these parameters, the ultimate film cooling performance was quantified in terms of net heat flux reduction. The dominant effect of roughness was a doubling of the heat transfer coefficients. Maximum adiabatic effectiveness levels were also decreased significantly. Relative to a film cooled smooth surface, a film cooled rough surface was found to increase the heat flux to the surface by 30% to 70%.

A Numerical and Experimental Investigation of Turbulent Heat Transport Downstream From an Abrupt Pipe Expansion

1983 ◽  
Vol 105 (4) ◽  
pp. 862-869 ◽  
Author(s):  
R. S. Amano ◽  
M. K. Jensen ◽  
P. Goel
Keyword(s):  
Heat Transfer ◽  
Numerical Solutions ◽  
Numerical Study ◽  
Separated Flow ◽  
Flow Region ◽  
Reynolds Numbers ◽  
Turbulent Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Pipe Expansion

An experimental and numerical study is reported on heat transfer in the separated flow region created by an abrupt circular pipe expansion. Heat transfer coefficients were measured along the pipe wall downstream from an expansion for three different expansion ratios of d/D = 0.195, 0.391, and 0.586 for Reynolds numbers ranging from 104 to 1.5 × 105. The results are compared with the numerical solutions obtained with the k ∼ ε turbulence model. In this computation a new finite difference scheme is developed which shows several advantages over the ordinary hybrid scheme. The study also covers the derivation of a new wall function model. Generally good agreement between the measured and the computed results is shown.

Heat Transfer Coefficients and Film Cooling Effectiveness on the Squealer Tip of a Gas Turbine Blade

2003 ◽  
Vol 125 (4) ◽  
pp. 648-657 ◽  
Author(s):  
Jae Su Kwak ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Rotor Blade ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio

Experimental investigations were performed to measure the detailed heat transfer coefficients and film cooling effectiveness on the squealer tip of a gas turbine blade in a five-bladed linear cascade. The blade was a two-dimensional model of a first stage gas turbine rotor blade with a profile of the GE-E3 aircraft gas turbine engine rotor blade. The test blade had a squealer (recessed) tip with a 4.22% recess. The blade model was equipped with a single row of film cooling holes on the pressure side near the tip region and the tip surface along the camber line. Hue detection based transient liquid crystals technique was used to measure heat transfer coefficients and film cooling effectiveness. All measurements were done for the three tip gap clearances of 1.0%, 1.5%, and 2.5% of blade span at the two blowing ratios of 1.0 and 2.0. The Reynolds number based on cascade exit velocity and axial chord length was 1.1×106 and the total turning angle of the blade was 97.9 deg. The overall pressure ratio was 1.2 and the inlet and exit Mach numbers were 0.25 and 0.59, respectively. The turbulence intensity level at the cascade inlet was 9.7%. Results showed that the overall heat transfer coefficients increased with increasing tip gap clearance, but decreased with increasing blowing ratio. However, the overall film cooling effectiveness increased with increasing blowing ratio. Results also showed that the overall film cooling effectiveness increased but heat transfer coefficients decreased for the squealer tip when compared to the plane tip at the same tip gap clearance and blowing ratio conditions.

Sign in / Sign up

Export Citation Format

Share Document