Micro-Scale Two-Phase Flow Heat Transport Device Driven by Electrohydrodynamic Conduction Pumping

2013 ◽  
Author(s):  
Viral K. Patel ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Heat Transport ◽  
Two Phase Flow ◽  
Operating Conditions ◽  
Electrode Spacing ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Micro Scale ◽  
Flow Heat ◽  
Transport Device

Micro-scale two-phase flow heat transport involves specialized devices that are used to remove large amounts of heat from small surface areas. They operate by circulating a working fluid through a heated space which causes phase change from liquid to vapor. During this process, a significant amount of heat is transported away from the heat source. Micro-scale heat transport devices are compact in size and the heat transfer coefficient can be orders of magnitude higher than in macro-scale for similar operating conditions. Thus, it is of interest to develop such devices for cooling of next-generation electronics and other applications with extremely large heat fluxes. The heat transport device presented in this paper is driven by electrohydrodynamic (EHD) conduction pumping. In EHD conduction pumping, when an electric field is applied to a dielectric liquid, flow is induced. The pump is installed in a two-phase flow loop and has a circular 1 mm diameter cross section with electrode spacing on the order of 120 μm. It acts to circulate the fluid in the loop and has a simple yet robust, non-mechanical design. Results from two-phase flow experiments show that it is easily controlled and such electrically driven pumps can effectively be used in heat transport systems.

A Mesoscale Electrohydrodynamic-Driven Two-Phase Flow Heat Transport Device in Circular Geometry and In-Tube Boiling Heat Transfer Coefficient Under Low Mass Flux

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Viral K. Patel ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Heat Transport ◽  
Boiling Heat Transfer ◽  
Two Phase Flow ◽  
Phase System ◽  
Phase Flow ◽  
Two Phase ◽  
Boiling Heat Transfer Coefficient ◽  
Low Mass ◽  
Flow Heat ◽  
Transport Device

Meso and microscale two-phase flow heat transport involves devices that are used to remove heat from small surface areas by circulating a working fluid through the heated space and causing phase change from liquid to vapor. There is an impetus to develop such devices for applications that require compact thermal management systems. The active, mesoscale two-phase flow heat transport device presented in this paper is driven solely by electrohydrodynamic (EHD) conduction pumping, and its heat transport characteristics are provided. An important understanding of the EHD conduction pump performance under a two-phase system versus single-phase system is also elucidated from these results. In addition, the ability to generate reliable low mass fluxes by this method has also allowed for determining local in-tube flow boiling heat transfer coefficient as a function of vapor quality in a mesoscale circular tube evaporator, providing limited but valuable information currently unavailable in the literature.

Numerical Analysis of Mass Flow Leakage Through Orifices for Supercritical CO2: Two-Phase Flow Effects

2020 ◽  
Author(s):  
Ladislav Vesely ◽  
Akshay Khadse ◽  
Andres Curbelo ◽  
Jayanta S. Kapat ◽  
Luca Petrungaro
Keyword(s):  
Mass Flow ◽  
Thermodynamic Equilibrium ◽  
Supercritical Co2 ◽  
Two Phase Flow ◽  
Operating Conditions ◽  
Working Fluid ◽  
Great Promise ◽  
Phase Flow ◽  
Computational Domain ◽  
Two Phase

Abstract Supercritical CO2 (sCO2) holds a great promise as a future working fluid for power generating Brayton cycles. One of the challenging research areas in sCO2 power cycles is flow leakage and the design of seals on the compressor side of the cycle. Given the compact nature of sCO2 turbomachinery, even a minimal amount of leakage can lead to a significant power efficiency loss. Hence accurate prediction of mass flow leakage rate becomes important. However, on the compressor side of the cycle, operating conditions across the seal lead to two-phase flow. This makes flow modeling very challenging because conventional one-phase flow CFD models cannot be used. This paper is an attempt to understand the behavior of two-phase sCO2 flow going through circular and annular orifices. The focus is to utilize commercially available CFD scheme for modeling phase change and two-phase flow through constrictions. Since the pressure loss across constrictions is also accompanied with reduction in temperature, the flow becomes two-phase by entering the saturation dome. CFD simulation is performed using commercially available software STAR CCM+. 2D axisymmetric geometry is considered as the computational domain. Eulerian Multi-phase Mixture model is used in conjunction with the Two-Phase Thermodynamic Equilibrium implementation. This model is intended for applications that involve two phases of the same substance that are in thermodynamic equilibrium. Fluid properties are defined over a large range of temperatures and pressures, including both the liquid and vapor phases.

Design and Performance of Two-Phase Flow Heat Transfer Experiment Platform Using R134a as Working Fluid

2010 ◽  
Author(s):  
Chang-Nian Chen ◽  
Ji-Tian Han ◽  
Li Shao ◽  
Tien-Chien Jen ◽  
Yi-Hsin Yen
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Two Phase Flow ◽  
Working Fluid ◽  
Phase Flow ◽  
Heat Transfer Characteristics ◽  
Transfer Experiment ◽  
Two Phase ◽  
Experiment Platform ◽  
Flow Heat

A two-phase flow heat transfer experiment platform using alternative refrigerant R134a as working fluid was designed and built to investigate the characteristics of two-phase flow heat transfer. It was primarily made up of circle power, heating/cooling sources, parallel test sections, accumulator and data acquisition system. The working loop was designed for performance pressure of 1.6 MPa and temperature of 200°C, preheated section power of 24 V × 300 A and test section of 60 V × 500 A. The refrigeration chilling unit had a maximum output of 50 kW. The preheated and test section were designed as horizontal helically-coiled tubes, and a visual reservoir made of electric melting-quartz glass was designed to observe flow patterns intuitively. Technology and methods related to fluid and mechanics were discussed in this paper including the aspects of materials and welding, sealing and heat preservation, special machining and accessories installation etc. Pressure testing, heat balance testing, heat transfer characteristics experiments were performed under various conditions to analyze the usability and stability of this platform. Test results showed that the leak ratio was no more than 250 Pa/h at 2.0 MPa and the heat loss of the system wrapped with PEF materials was less than 5%. Under the conditions of pressures of 0.30–0.95 MPa, mass fluxes of 120–620 kg/m2s, inlet qualities of −0.08–0.38 and heated power of 0.45–1.30 kW, R134a two-phase flow boiling heat transfer characteristics were investigated and discussed in detail. This platform can be used for studying the characteristics of two-phase flow pressure drop, boiling heat transfer and fluid-to-fluid modeling technique etc.

Visualization of Two-Phase Flow in 3D Printed Polycarbonate Pulsating Heat Pipe With Aluminum Substrate

2018 ◽  
Author(s):  
Takahiro Arai ◽  
Masahiro Kawaji ◽  
Yasushi Koito
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Two Phase Flow ◽  
Aluminum Plate ◽  
Working Fluid ◽  
Phase Flow ◽  
Pulsating Heat Pipe ◽  
Two Phase ◽  
Flow Channels ◽  
Heat Transport Capability

A pulsating heat pipe (PHP) is a passive device with a good heat transport capability compared to other heat pipes. This paper describes an experimental investigation of a PHP with a serpentine channel fabricated by using a 3-D printer. The configuration of the flow channels in the PHP was close to that of commercially available PHPs made entirely of aluminum. To improve the heat transport capability and enable flow visualization, an aluminum plate was used on one side as the heat-transfer surface, on which transparent flow channels were fabricated by a 3-D printer and a polycarbonate filament. The interface between the aluminum plate and polycarbonate flow channel was cemented with a heat-resistant glue to ensure long term sealing. HFE-7000 was used as a working fluid. Oscillating two-phase flow in the PHP was observed with a high-speed digital video camera and transient surface temperatures at evaporator, insulator and condenser sections were measured by fine diameter thermocouples. The two-phase flow and thermal characteristics of the PHP at different heater power levels are presented.

Analysis of the two-phase flow, heat transfer, and instability characteristics in a loop thermosyphon

2021 ◽  
Vol 79 (9) ◽  
pp. 656-680
Author(s):  
Yun Liu ◽  
Zhigang Li ◽  
Yuyan Jiang ◽  
Cong Guo ◽  
Dawei Tang
Keyword(s):  
Heat Transfer ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Heat

Experimental Study of Linear and Radial Two-Phase Heat Transport Devices Driven by Electrohydrodynamic Conduction Pumping

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Matthew R. Pearson ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Heat Source ◽  
Capillary Pressure ◽  
Heat Transport ◽  
Radial Direction ◽  
Heat Pipes ◽  
Working Fluid ◽  
Phase Flow ◽  
Transport Capacity ◽  
Two Phase ◽  
Capillary Phenomenon

Heat pipes are well known as simple and effective heat transport devices, utilizing two-phase flow and the capillary phenomenon to remove heat. However, the generation of capillary pressure requires a wicking structure and the overall heat transport capacity of the heat pipe is generally limited by the amount of capillary pressure generation that the wicking structure can achieve. Therefore, to increase the heat transport capacity, the capillary phenomenon must be either augmented or replaced by some other pumping technique. Electrohydrodynamic (EHD) conduction pumping can be readily used to pump a thin film of a dielectric liquid along a surface, using electrodes that are embedded into the surface. In this study, two two-phase heat transport devices are created. The first device transports the heat in a linear direction. The second device transports the heat in a radial direction from a central heat source. The radial pumping configuration provides several advantages. Most notably, the heat source is wetted with fresh liquid from all directions, thereby reducing the amount of distance that must be travelled by the working fluid. The power required to operate the EHD conduction pumps is a trivial amount relative to the heat that is transported.

Sign in / Sign up

Export Citation Format

Share Document