Transient Two-Phase Flow Patterns by Application of a High Voltage Pulse Width Modulated Signal and the Effect on Condensation Heat Transfer

2010 ◽  
Author(s):  
K. Ng ◽  
C. Y. Ching ◽  
J. S. Cotton
Keyword(s):  
Heat Transfer ◽  
Flow Pattern ◽  
Electric Fields ◽  
High Voltage ◽  
Mass Flux ◽  
Pulse Width ◽  
Flow Patterns ◽  
Phase Flow ◽  
Two Phase ◽  
Pulse Width Modulated

The objectives of this study are (i) to determine the transient phase redistributions of a two-phase flow in a smooth horizontal annular channel by applying high voltage pulses to induce electric fields and (ii) to quantify the resultant changes in the condensation heat transfer. The experiments were performed using refrigerant R-134a flowing in a tube that was cooled on the outside by a counter-current flow of water. The electric fields are established by applying high voltage to a concentric rod electrode inside a grounded tube. The effect of the electrohydrodynamic (EHD) forces on the changes to the initial stratified/stratified wavy flow pattern was visualized using a high speed camera. The EHD effect results in the redistribution of the liquid-vapour phase within the channel and unique flow structures, such as twisted liquid cones and entrained droplets, are observed. These structures only appear during the initial application of EHD and are absent in the steady state flow pattern. Experiments were performed using a 8kV pulse width modulated (PWM) signal with duty cycles ranging from 0–100% to evaluate the heat transfer and pressure drop characteristics of the transient EHD flow patterns. The resultant heat transfer increased with the duty cycle to approximately 2.7-fold at a low mass flux (45–55kg/m2s) and 1.2-fold at a high mass flux (110kg/m2s). The enhancement was higher as the pulse width was increased.

Transient Two-Phase Flow Patterns by Application of a High Voltage Pulse Width Modulated Signal and the Effect on Condensation Heat Transfer

2011 ◽  
Vol 133 (9) ◽  
Author(s):  
Kevin Ng ◽  
Chan Y. Ching ◽  
James S. Cotton
Keyword(s):  
Heat Transfer ◽  
Electric Fields ◽  
High Voltage ◽  
Mass Flux ◽  
Pulse Width ◽  
Annular Channel ◽  
Flow Patterns ◽  
Phase Flow ◽  
Two Phase ◽  
Pulse Width Modulated

The objectives of this study are (i) to determine the transient phase redistributions of a two-phase flow in a smooth horizontal annular channel by applying high voltage pulses to induce electric fields and (ii) to quantify the resultant changes in the condensation heat transfer. The experiments were performed using refrigerant R-134a flowing in the annular channel that was cooled on the outside by a counter-current flow of water. The electric fields are established by applying high voltage to a concentric rod electrode inside a grounded tube. The effect of the electrohydrodynamic (EHD) forces on the changes to the initial stratified/stratified wavy flow pattern was visualized using a high speed camera. The EHD effect results in the redistribution of the liquid–vapor phase within the channel and unique flow structures, such as twisted liquid cones and entrained droplets, are observed. These structures only appear during the initial application of EHD and are absent in the steady state. Experiments were performed using a 8 kV pulse width modulated (PWM) signal with duty cycles ranging from 0% to 100% to evaluate the heat transfer and pressure drop characteristics of the transient EHD flow patterns. The resultant heat transfer increased with the duty cycle to approximately 2.7-fold at a mass flux of 45–55 kg/m2s and 1.2-fold at a mass flux of 110 kg/m2s. The enhancement was higher as the pulse width was increased.

Two-Phase Flow Patterns During Microchannel Vaporization of CO2 at Near-Critical Pressures

2003 ◽  
Author(s):  
Jostein Pettersen
Keyword(s):  
Heat Transfer ◽  
Flow Pattern ◽  
Mass Flux ◽  
Two Phase Flow ◽  
Bubble Formation ◽  
Glass Tube ◽  
Flow Patterns ◽  
High Mass ◽  
Phase Flow ◽  
Two Phase

Carbon dioxide (CO2 / R-744) is receiving renewed interest as a refrigerant, in many cases based on systems with microchannel heat exchangers that have high pressure capability, efficient heat transfer, and compact design. A good understanding of two-phase flow of evaporating CO2 in microchannels is needed to analyze and predict heat transfer. A special test rig was built in order to observe two-phase flow patterns, using a horizontal quartz glass tube with ID 0.98 mm, externally coated by a transparent resistive film. Heat flux was obtained by applying DC power to the film, and flow patterns were recorded at 4000 or 8000 frames per second by a digital video camera. Flow patterns were recorded for temperatures 20°C and 0°C, and for mass flux ranging from 100 to 580 kgm−2s−1. The observations showed a dominance of intermittent (slug) flow at low x, and wavy annular flow with entrainment of droplets at higher x. At high mass flux, the annular/entrained flow pattern could be described as dispersed. The aggravated dryout problem reported from heat transfer experiments at high mass flux could be explained by increased entrainment. Stratified flow was not observed in the tests with heat load. Bubble formation and growth could be observed in the liquid film, and the presence of bubbles gave differences in flow pattern compared to adiabatic flow. The flow pattern observations did not fit generalized maps or transition lines showed in the literature.

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2003 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase ◽  
Micro Channels

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406 × 2.032 mm cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal that the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Annual flow is identified as the dominant flow pattern for conditions relevant to two-phase micro-channel heat sinks, and forms the basis for development of a theoretical model for both pressure drop and heat transfer in micro-channels. Features unique to two-phase micro-channel flow, such as laminar liquid and gas flows, smooth liquid-gas interface, and strong entrainment and deposition effects are incorporated into the model. The model shows good agreement with experimental data for water-cooled heat sinks.

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2004 ◽  
Vol 126 (3) ◽  
pp. 288-300 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406×2.032mm2 cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Features unique to two-phase micro-channel flow were identified and employed to validate key assumptions of an annular flow boiling model that was previously developed to predict pressure drop and heat transfer in two-phase micro-channel heat sinks. This earlier model was modified based on new findings from the adiabatic two-phase flow study. The modified model shows good agreement with experimental data for water-cooled heat sinks.

Two-Phase Flow Patterns and Flow-Pattern Maps: Fundamentals and Applications

2008 ◽  
Vol 61 (5) ◽  
Author(s):  
Lixin Cheng ◽  
Gherhardt Ribatski ◽  
John R. Thome
Keyword(s):  
Heat Transfer ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Newtonian Fluids ◽  
Future Research ◽  
Phase Flow ◽  
Context Modeling ◽  
Two Phase ◽  
Specific Flow

A comprehensive review of the studies of gas-liquid two-phase flow patterns and flow-pattern maps at adiabatic and diabatic conditions is presented in this paper. Especially, besides other situations, this review addresses the studies on microscale channels, which are of great interest in recent years. First, a fundamental knowledge of two-phase flow patterns and their application background is briefly introduced. The features of two-phase flow patterns and flow-pattern maps at adiabatic and diabatic conditions are reviewed, including recent studies for ammonia, new refrigerants, and CO2. Then, fundamental studies of gas-liquid flow patterns and flow-pattern maps are presented. In the experimental context, studies of flow patterns and flow-pattern maps in macro- and microscale channels, across tube bundles, at diabatic and adiabatic conditions, under microgravity and in complex channels are summarized. In addition, studies on highly viscous Newtonian fluids (non-Newtonian fluids are beyond the scope of this review) are also mentioned. In the theoretical context, modeling of flow-regime transitions, specific flow patterns, stability, and interfacial shear is reviewed. Next, flow-pattern-based heat transfer and pressure drop models and heat transfer models for specific flow patterns such as slug flow and annular flow are reviewed. Based on this review, recommendations for future research directions have been given.

Flow Boiling Heat Transfer, Pressure Drop, and Flow Pattern for CO2 in a 3.5mm Horizontal Smooth Tube

2009 ◽  
Vol 131 (9) ◽  
Author(s):  
Chang Yong Park ◽  
Pega Hrnjak
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Flow Boiling Heat Transfer

Abstract C O 2 flow boiling heat transfer coefficients and pressure drop in a 3.5mm horizontal smooth tube are presented. Also, flow patterns were visualized and studied at adiabatic conditions in a 3mm glass tube located immediately after a heat transfer section. Heat was applied by a secondary fluid through two brass half cylinders to the test section tubes. This research was performed at evaporation temperatures of −15°C and −30°C, mass fluxes of 200kg∕m2s and 400kg∕m2s, and heat flux from 5kW∕m2 to 15kW∕m2 for vapor qualities ranging from 0.1 to 0.8. The CO2 heat transfer coefficients indicated the nucleate boiling dominant heat transfer characteristics such as the strong dependence on heat fluxes at a mass flux of 200kg∕m2s. However, enhanced convective boiling contribution was observed at 400kg∕m2s. Surface conditions for two different tubes were investigated with a profilometer, atomic force microscope, and scanning electron microscope images, and their possible effects on heat transfer are discussed. Pressure drop, measured at adiabatic conditions, increased with the increase of mass flux and quality, and with the decrease of evaporation temperature. The measured heat transfer coefficients and pressure drop were compared with general correlations. Some of these correlations showed relatively good agreements with measured values. Visualized flow patterns were compared with two flow pattern maps and the comparison showed that the flow pattern maps need improvement in the transition regions from intermittent to annular flow.

Detecting the Flow Pattern Transition in the Gas-Liquid Two-Phase Flow Using Multivariate Multi-Scale Entropy Analysis

2019 ◽  
Vol 74 (10) ◽  
pp. 837-848 ◽  
Author(s):  
Yudong Liu ◽  
Dayang Wang ◽  
Yingyu Ren ◽  
Ningde Jin
Keyword(s):  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Mean Value ◽  
Entropy Rate ◽  
Permutation Entropy ◽  
Phase Flow ◽  
Two Phase ◽  
Multi Scale ◽  
Flow Pattern Transition

AbstractDue to the complex flow structure and non-uniform phase distribution in the vertical upward gas-liquid two-phase flow, an eight-electrode rotating electric field conductance sensor is used to obtain multi-channel conductance signals. The flow patterns of the vertical upward gas-liquid two-phase flow are classified according to the images obtained from a high-speed camera. Then, we employ the multivariate weighted multi-scale permutation entropy (MWMPE) to detect the instability of flow pattern transition in the gas-liquid two-phase flow. Afterwards, we compare the results of the MWMPE with those of the single-channel weighted multi-scale permutation entropy (SCWMPE) and multivariate multi-scale sample entropy (MMSE). The comparison results indicate that, compared with the SCWMPE and MMSE, the MWMPE has superior performance in terms of the high-resolution presentation of flow instability in the gas-liquid two-phase flow. Finally, we extract the mean value of the MWMPE in whole scales and the entropy rate of the MWMPE in the small scales. The results indicate that the normalized mean value and normalized entropy rate of MWMPE are very sensitive to the transitions of flow patterns, thus allowing the detection of the instability of flow pattern transition.

Numerical and experimental investigation on the effect of the two-phase flow pattern on heat transfer of piston cooling gallery

2019 ◽  
Vol 20 (5) ◽  
pp. 507 ◽  
Author(s):  
Lijun Deng ◽  
Jian Zhang ◽  
Guannan Hao ◽  
Jing Liu
Keyword(s):  
Heat Transfer ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Unstable Wave ◽  
Fluid Viscosity ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Process ◽  
The Impact ◽  
Piston Cooling

To study factors affecting the formation and conversion of two-phase flow pattern as well as the heat transfer of piston cooling gallery, a transient visual target test bench was set up to research the oscillatory flow characteristics in the cooling gallery under idle condition of the engine. The computational fluid dynamics (CFD) was employed while dynamic mesh technology, SST k–ω turbulence model and volume of fluid (VOF) two-phase flow model were applied to simulate the flow process of piston cooling gallery so as to predict the distribution pattern of two-phase flow. Simulation results were in good agreement with that experimentally obtained. It was observed that in the reciprocating movement of the piston, the action of two-phase flow oscillation was severe, forming some unstable wave flows and slug flows. Results show that under the same pipe diameter, the increase of fluid viscosity results in the decrease of amplitude and the increase of the liquid slugs number as well as the enhancement on heat transfer effect. In addition, it was revealed that injection pressure has little effect on the two-phase flow pattern. However, when the pressure is reduced, the change of the liquid phase is weakened and the locations of flow pattern transition move towards to the behind, thus the impact on the heat transfer is also faint.

Flow Boiling Visualization of R-134a in a Vertical Channel of Small Diameter

2007 ◽  
Author(s):  
Claudi Marti´n-Callizo ◽  
Bjo¨rn Palm ◽  
Wahib Owhaib ◽  
Rashid Ali
Keyword(s):  
Flow Pattern ◽  
Annular Flow ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Bubbly Flow ◽  
Flow Patterns ◽  
Phase Flow ◽  
Two Phase ◽  
R 134A ◽  
Heated Length

The present work reports on flow boiling visualization of refrigerant R-134a in a vertical circular channel with internal diameter of 1.33 mm and 235 mm in heated length. Quartz tube with a homogeneous ITO-coating is used allowing heating and simultaneous visualization. Flow patterns have been observed along the heated length with the aid of a digital camera with close-up lenses. From the flow boiling visualization, seven distinct two-phase flow patterns have been observed: Isolated bubbly flow, confined bubbly flow, slug flow, churn flow, slug-annular flow, annular flow, and mist flow. Two-phase flow pattern observations are presented in the form of flow pattern maps. Finally, the experimental flow pattern map is compared to models developed for conventional sizes as well as to a microscale map for air-water mixtures available in the literature, showing a large discrepancy.

Experimental Investigation on Flow Patterns and Frictional Pressure Drop of Downward Air-Water Two-Phase Flow in Vertical Pipes

2013 ◽  
Author(s):  
Yuqing Xue ◽  
Huixiong Li ◽  
Tianyou Sheng ◽  
Changjiang Liao
Keyword(s):  
Pressure Drop ◽  
Flow Pattern ◽  
Oil Recovery ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Phase Flow ◽  
Vertical Pipe ◽  
Two Phase Flows ◽  
Two Phase ◽  
Frictional Pressure Drop

A large amount of air need be transported into the reservoir in the deep stratum to supply oxygen to some microbes in Microbial Enhanced Oil Recovery (MEOR). Air-water two-phase flows downward along vertical pipeline during the air transportation. Base on the experiment data described in this paper, the characteristics of air-water two phase flow patterns were investigated. The flow pattern map of air-water two phase flows in the pipe with inner diameter of 65 mm was drawn, criterions of flow pattern transition were discussed, and the dynamic signals of the pressure and the differential pressure of the two phase flow were recorded to characterize the three basic flow regimes indirectly. The frictional pressure drop of downward flow in vertical pipe must not be disregarded contrast with upward two phase flow in the vertical pipe because the buoyancy must be overcame when the gas flows downward along pipe, and there would be a maximum value of frictional when the flow pattern translated from slug flow to churn flow.

Sign in / Sign up

Export Citation Format

Share Document