Turbulent Flow in Closely-Pitched Internally Enhanced Tubes

2000 ◽  
Author(s):  
T. S. Ravigururajan ◽  
J. Srinivasan
Keyword(s):  
Heat Transfer ◽  
Turbulent Flow ◽  
Friction Factor ◽  
Helix Angle ◽  
Independent Study ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Flow Parameters ◽  
Wide Range ◽  
Enhanced Tubes

Abstract General correlations are developed and verified for friction factor and heat transfer coefficients for single-phase turbulent flow in internally augmented tubes, with low pitch to height ratios. Data from existing investigations were collected for a wide range of tube parameters with e/d: 0.01 to 0.2; p/e: < 8; α/90: 0.2 to 1.0, and flow parameters; Re: 2000 to 250,000 and Pr: 0.66 to 37.6. The data were applied to a linear model to get normalized correlations that were then modified to approach smooth tube correlations, as the roughness variables became very small. The correlations predicted 92% of data from an independent study on microfin tubes within ± 30%. For closely-pitched enhanced tubes, the proposed correlations predict heat transfer/friction factor with better overall accuracy and are suitable for different types of internal enhancements. The heat transfer increases with decreasing p/e ratio and increasing helix angle. The effects of roughness height and pitch on both friction and heat transfer are similar to that experienced in traditional enhancement design (p/e > 8).

Turbulent Flow Friction and Heat Transfer Characteristics of Single- and Multistart Spirally Enhanced Tubes

1986 ◽  
Vol 108 (1) ◽  
pp. 55-61 ◽  
Author(s):  
R. Sethumadhavan ◽  
M. Raja Rao
Keyword(s):  
Heat Transfer ◽  
Turbulent Flow ◽  
Evaluation Criteria ◽  
Helix Angle ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Aspect Ratios ◽  
Friction Factors ◽  
Enhanced Tubes ◽  
Momentum And Heat Transfer

Investigations have been carried out on heat transfer and frictional characteristics of five spirally corrugated tubes of one to four corrugation starts, having the same helix angle, but of varying geometrical aspect ratios, for the turbulent flow of water and 50 percent glycerol. The thermal performance of these tubes was found to be superior compared to a smooth tube. Friction factors and heat transfer coefficients in these rough tubes were analysed on the basis of momentum and heat transfer analogy, and the correlation obtained was tested with the present data and also the published results of previous investigators. Performance evaluation criteria were used for the quantitative demonstration of the benefits offered by these spirally corrugated tubes for heat exchanger applications.

SINGLE-PHASE HEAT TRANSFER AND PRESSURE DROP INSIDE INTERNALLY HELICAL-GROOVED HORIZONTAL SMALL-DIAMETER TUBES

2012 ◽  
Vol 20 (04) ◽  
pp. 1250022 ◽  
Author(s):  
NORIHIRO INOUE ◽  
JUNYA ICHINOSE
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Laminar Flow ◽  
Turbulent Flow ◽  
Single Phase ◽  
Small Diameter ◽  
Flow Region ◽  
Helix Angle ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

An experimental study on pressure drop and heat transfer in single-phase was carried out using 10 types of internally helical-grooved and smooth small-diameter tubes with an outside diameter of 4 mm. The results are listed below: (1) In the turbulent flow region, fin height had the greatest effect, helix angle had only a minor effect, and the number of grooves had almost no effect upon the pressure drop versus the mass flow rate of the 4-mm grooved small-diameter tubes. In the laminar flow region, except for fin height, the shapes of the internal grooves had scarcely any effect upon pressure drop. (2) In the turbulent flow region, the heat transfer coefficients of the 4-mm grooved small-diameter tubes were greatly affected by fin height. The heat transfer coefficients became the maximum when a helix angle was near 15°, and there is a different tendency in the experiments of the pressure drop. On the other hand, there is almost no effect of the number of grooves. In the laminar flow region, there were no large differences in the heat transfer coefficients between the internally helical-grooved tubes and smooth small-diameter tube. (3) New empirical correlations for the friction factor and heat transfer coefficient in the laminar and turbulent flow regions were developed based on the experimental values. (4) The performance assessment in consideration of both heat transfer and pressure drop was indicated by using Colburn's analogy.

scholarly journals Mass and Heat Transfer Coefficients in Automotive Exhaust Catalytic Converter Channels

Catalysts ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 507
Author(s):  
Chrysovalantis C. Templis ◽  
Nikos G. Papayannakos
Keyword(s):  
Heat Transfer ◽  
Flow Reactor ◽  
Catalytic Converter ◽  
Reaction Rates ◽  
Cfd Model ◽  
Automotive Exhaust ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Wide Range ◽  
Mass And Heat Transfer

Mass and heat transfer coefficients (MTC and HTC) in automotive exhaust catalytic monolith channels are estimated and correlated for a wide range of gas velocities and prevailing conditions of small up to real size converters. The coefficient estimation is based on a two dimensional computational fluid dynamic (2-D CFD) model developed in Comsol Multiphysics, taking into account catalytic rates of a real catalytic converter. The effect of channel size and reaction rates on mass and heat transfer coefficients and the applicability of the proposed correlations at different conditions are discussed. The correlations proposed predict very satisfactorily the mass and heat transfer coefficients calculated from the 2-D CFD model along the channel length. The use of a one dimensional (1-D) simplified model that couples a plug flow reactor (PFR) with mass transport and heat transport effects using the mass and heat transfer correlations of this study is proved to be appropriate for the simulation of the monolith channel operation.

Heat Transfer in Rotating Serpentine Coolant Passage With Ribbed Walls at Low Mach Numbers

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
Shang-Feng Yang ◽  
Je-Chin Han ◽  
Salam Azad ◽  
Ching-Pang Lee
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Low Mach Number ◽  
Heat Transfer Coefficients ◽  
Rotation Numbers ◽  
Wide Range ◽  
Mach Numbers

This paper experimentally investigates the effect of rotation on heat transfer in typical turbine blade serpentine coolant passage with ribbed walls at low Mach numbers. To achieve the low Mach number (around 0.01) condition, pressurized Freon R-134a vapor is utilized as the working fluid. The flow in the first passage is radial outward, after the 180 deg tip turn the flow is radial inward to the second passage, and after the 180 deg hub turn the flow is radial outward to the third passage. The effects of rotation on the heat transfer coefficients were investigated at rotation numbers up to 0.6 and Reynolds numbers from 30,000 to 70,000. Heat transfer coefficients were measured using the thermocouples-copper-plate-heater regional average method. Heat transfer results are obtained over a wide range of Reynolds numbers and rotation numbers. An increase in heat transfer rates due to rotation is observed in radially outward passes; a reduction in heat transfer rate is observed in the radially inward pass. Regional heat transfer coefficients are correlated with Reynolds numbers for nonrotation and with rotation numbers for rotating condition, respectively. The results can be useful for understanding real rotor blade coolant passage heat transfer under low Mach number, medium–high Reynolds number, and high rotation number conditions.

Heat Transfer for Forced Convection Past Coiled Wires

1990 ◽  
Vol 112 (4) ◽  
pp. 921-925 ◽  
Author(s):  
M. Dietrich ◽  
R. Blo¨chl ◽  
H. Mu¨ller-Steinhagen
Keyword(s):  
Heat Transfer ◽  
Forced Convection ◽  
Measured Data ◽  
Subcooled Boiling ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Coil Geometry ◽  
Coil Diameter ◽  
Wide Range ◽  
Laminar And Turbulent Flow

Heat transfer coefficients were measured for forced convection of isobutanol in crossflow past coiled wires with different coil geometries. Flow rate and heat flux have been varied over a wide range to include laminar and turbulent flow for convective sensible and subcooled boiling heat transfer. To investigate the effect of coil geometry on heat transfer, the wire diameter, coil diameter, and coil pitch were varied systematically. The measured data are compared with the predictions of four correlations from the literature.

Thermally Developing Single-Phase Flows in Microtubes

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Mehmed Rafet Özdemir ◽  
Ali Koşar
Keyword(s):  
Heat Transfer ◽  
Turbulent Flow ◽  
Single Phase ◽  
High Mass ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Mass Fluxes ◽  
Friction Factors ◽  
Developing Flow ◽  
Theoretical Predictions

The pressure drop and heat transfer due to the flow of de-ionized water at high mass fluxes in microtubes of ∼ 254 μm and ∼ 685 μm inner diameters is investigated in the laminar, transition and the turbulent flow regimes. The flow is hydrodynamically fully developed and thermally developing. The experimental friction factors and heat transfer coefficients are respectively predicted to within ±20% and ±30% by existing open literature correlations. Higher single phase heat transfer coefficients were obtained with increasing mass fluxes, which is motivating to operate at high mass fluxes and under thermally developing flow conditions. The transition to turbulent flow and friction factors for both laminar and turbulent conditions were found to be in agreement with existing theory. A reasonable agreement was present between experimental results and theoretical predictions recommended for convective heat transfer in thermally developing flows.

Nucleate Pool Boiling Heat Transfer of R134a and R134a-PVE Lubricant Mixtures on Smooth and Five Enhanced Tubes

2010 ◽  
Vol 132 (11) ◽  
Author(s):  
Wen-Tao Ji ◽  
Ding-Cai Zhang ◽  
Nan Feng ◽  
Jian-Fei Guo ◽  
Mitsuharu Numata ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Saturation Temperature ◽  
Transfer Coefficients ◽  
Pool Boiling Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Enhanced Tubes ◽  
Mass Fractions

Pool boiling heat transfer coefficients of R134a with different lubricant mass fractions for one smooth tube and five enhanced tubes were tested at a saturation temperature of 6°C. The lubricant used was polyvinyl ether. The lubrication mass fractions were 0.25%, 0.5%, 1.0%, 2.0%, 3.0%, 5.0%, 7.0%, and 10.0%, respectively. Within the tested heat flux range, from 9000 W/m2 to 90,000 W/m2, the lubricant generally has a different influence on pool boiling heat transfer of these six tubes.

Sign in / Sign up

Export Citation Format

Share Document