Numerical Study of Two-Phase Flow in a Horizontal Pipeline Using an Unconditionally Hyperbolic Two-Fluid Model

2018 ◽  
Author(s):  
Raphael V. N. de Freitas ◽  
Carina N. Sondermann ◽  
Rodrigo A. C. Patricio ◽  
Aline B. Figueiredo ◽  
Gustavo C. R. Bodstein ◽  
...  
Keyword(s):  
Volume Fraction ◽  
Numerical Study ◽  
Fluid Model ◽  
Momentum Conservation ◽  
Design Stage ◽  
Two Phase Flows ◽  
Two Phase ◽  
Efficient Manner ◽  
Two Fluid Model ◽  
Two Fluid

Numerical simulation is a very useful tool for the prediction of physical quantities in two-phase flows. One important application is the study of oil-gas flows in pipelines, which is necessary for the proper selection of the equipment connected to the line during the pipeline design stage and also during the pipeline operation stage. The understanding of the phenomena present in this type of flow is more crucial under the occurrence of undesired effects in the duct, such as hydrate formation, fluid leakage, PIG passage, and valve shutdown. An efficient manner to model two-phase flows in long pipelines regarding a compromise between numerical accuracy and cost is the use of a one-dimensional two-fluid model, discretized with an appropriate numerical method. A two-fluid model consists of a system of non-linear partial differential equations that represent the mass, momentum and energy conservation principles, written for each phase. Depending on the two-fluid model employed, the system of equations may lose hyperbolicity and render the initial-boundary-value problem illposed. This paper uses an unconditionally hyperbolic two-fluid model for solving two-phase flows in pipelines in order to guarantee that the solution presents physical consistency. The mathematical model here referred to as the 5E2P (five equations and two pressures) comprises two equations of continuity and two momentum conservation equations, one for each phase, and one equation for the transport of the volume fraction. A priori this model considers two distinct pressures, one for each phase, and correlates them through a pressure relaxation procedure. This paper presents simulation cases for stratified two-phase flows in horizontal pipelines solved with the 5E2P coupled with the flux corrected transport method. The objective is to evaluate the numerical model capacity to adequately describe the velocities, pressures and volume fraction distributions along the duct.

scholarly journals Computational investigation of liquid-solid slurry flow through an expansion in a rectangular duct

2014 ◽  
Vol 62 (3) ◽  
pp. 234-240 ◽  
Author(s):  
Gianandrea Vittorio Messa ◽  
Stefano Malavasi
Keyword(s):  
Volume Fraction ◽  
Particle Density ◽  
Fluid Model ◽  
Solid Volume Fraction ◽  
Solid Particles ◽  
Rectangular Duct ◽  
Two Phase ◽  
Horizontal Pipe ◽  
Two Fluid Model ◽  
Two Fluid

Abstract The flow of a mixture of liquid and solid particles at medium and high volume fraction through an expansion in a rectangular duct is considered. In order to improve the modelling of the phenomenon with respect to a previous investigation (Messa and Malavasi, 2013), use is made of a two-fluid model specifically derived for dense flows that we developed and implemented in the PHOENICS code via user-defined subroutines. Due to the lack of experimental data, the two-fluid model was validated in the horizontal pipe case, reporting good agreement with measurements from different authors for fully-suspended flows. A 3D system is simulated in order to account for the effect of side walls. A wider range of the parameters characterizing the mixture (particle size, particle density, and delivered solid volume fraction) is considered. A parametric analysis is performed to investigate the role played by the key physical mechanisms on the development of the two-phase flow for different compositions of the mixture. The main focuses are the distribution of the particles in the system and the pressure recovery

Interfacial Pressure Coefficient for Ellipsoids and Its Effect on the Two-Fluid Model Eigenvalues

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Avinash Vaidheeswaran ◽  
Martin Lopez de Bertodano
Keyword(s):  
Fluid Model ◽  
Pressure Coefficient ◽  
Well Posedness ◽  
Virtual Mass ◽  
Two Phase Flows ◽  
Two Phase ◽  
Pressure Coefficients ◽  
Interfacial Pressure ◽  
Two Fluid Model ◽  
Two Fluid

Analytical expressions for interfacial pressure coefficients are obtained based on the geometry of the bubbles occurring in two-phase flows. It is known that the shape of the bubbles affects the virtual mass and interfacial pressure coefficients, which in turn determines the cutoff void fraction for the well-posedness of two-fluid model (TFM). The coefficient used in the interfacial pressure difference correlation is derived assuming potential flow around a perfect sphere. In reality, the bubbles seen in two-phase flows get deformed, and hence, it is required to estimate the coefficients for nonspherical geometries. Oblate and prolate ellipsoids are considered, and their respective coefficients are determined. It is seen that the well-posedness limit of the TFM is determined by the combination of virtual mass and interfacial pressure coefficient used. The effect of flow separation on the coefficient values is also analyzed.

A NUMERICAL STUDY OF TWO-PHASE FLOW USING A TWO-DIMENSIONAL TWO-FLUID MODEL

2004 ◽  
Vol 45 (10) ◽  
pp. 1049-1066 ◽  
Author(s):  
Moon-Sun Chung ◽  
Seung-Kyung Pak ◽  
Keun-Shik Chang
Keyword(s):  
Two Phase Flow ◽  
Numerical Study ◽  
Fluid Model ◽  
Phase Flow ◽  
Two Dimensional ◽  
Two Phase ◽  
Two Fluid Model ◽  
Two Fluid

Analyses of Hydrodynamic Structure of Water Jet and Its Application to Jet Grouting

2003 ◽  
Author(s):  
Kenji Yoshida ◽  
Isao Kataoka ◽  
Hiroshi Yoshida ◽  
Mitsuru Yokoo ◽  
Kiyoshi Horii
Keyword(s):  
Constitutive Equations ◽  
Fluid Model ◽  
Momentum Conservation ◽  
Water Jet ◽  
Two Phase ◽  
Dispersed Flow ◽  
Two Fluid Model ◽  
Basic Equations ◽  
Physical Phenomena ◽  
Two Fluid

Analyses of water jet based on two-fluid model of two-phase dispersed flow have been carried out for single water jet and cross water jet in relation to the water jet technology in civil engineering. Mass and momentum conservation equations for liquid phase (droplet) gas phase (air) were formulated separately (two-fluid model formulation). Physical modeling of diffusion of droplets, drag coefficient of droplet in dispersed flow, shear stress at jet interface, etc has been carried out in detail and constitutive equations for these physical phenomena have been developed. Based on the two-fluid model basic equations and constitutive equations, one-dimensional analysis has been carried out considering simplified model. In the practical application of present analyses, some preliminary analyses on cross jet where two water jets collide with certain collision angles have been carried out and the predicted results reasonably explain the experimental results.

Sign in / Sign up

Export Citation Format

Share Document