A 3D Finite Element Analysis Study of the Jawbones Response to Osseodensification and Conventional Drilling

2020 ◽  
Author(s):  
Razan Alaqeely ◽  
Mohammad AlDosari ◽  
Nadir Babay ◽  
Al-Hussain Abdulbari ◽  
Ala Ba Hadi ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Trabecular Bone ◽  
Cone Beam Ct ◽  
Primary Stability ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Linear Pattern ◽  
Pull Out ◽  
Conventional Drilling

Abstract Osseodensification is used to densify natural bone and increase dental implant stability. This work aims to compare, using finite element analysis, the stress generated on different jawbone areas between conventional drilling (OD) and osseodensification drilling (CD). Cone-beam CT scans of four different edentulous patients were obtained. Implant insertion and removal in the four bone models were simulated for the two different drilling techniques. Materials distribution was set as homogeneous throughout each part. In the OD technique, a new densified region was formed with new material properties based on a relation between density and elasticity. Material distribution of the densified regions was assumed to be a non-homogenous linear pattern and its gradual variation complies with the graph-related slope equations. Von-Mises stress for cortical and trabecular bone was significantly higher in the CD model in comparison to their values in the OD, as densified regions have absorbed most of the stresses and restricted their propagation. The same phenomenon was observed in the implant pull-out bone model. The OD technique was found to affect the primary stability of dental implants positively. The bone types present in different jawbone regions react differently to this technique according to the percentage of trabecular bone to cortical bone.

Finite Element Analysis of an Osseointegrated Stepped Screw Dental Implant

2004 ◽  
Vol 30 (4) ◽  
pp. 223-233 ◽  
Author(s):  
J. P. Geng ◽  
W. Xu ◽  
K. B. C. Tan ◽  
G. R. Liu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Trabecular Bone ◽  
Cortical Bone ◽  
Dental Implant ◽  
Elastic Moduli ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Data Set ◽  
Bone Level

Abstract An osseointegrated stepped screw dental implant was evaluated using 2-dimensional finite element analysis (FEA). The implant was modeled in a cross section of the posterior human mandible digitized from a computed tomography (CT) generated patient data set. A 15-mm regular platform (RP) Branemark implant with equivalent length and neck diameter was used as a control. The study was performed under a number of clinically relevant parameters: loading at the top of the transmucosal abutment in vertical, horizontal, and 45° oblique 3 orientations. Elastic moduli of the mandible varied from a normal cortical bone level (13.4 GPa) to a trabecular bone level (1.37 GPa). The study indicated that an oblique load and elastic moduli of the cortical bone are important parameters to the implant design optimization. Compared with the cylindrical screw implant, the maximum von Mises stress of the stepped screw implant model was 17.9% lower in the trabecular bone-implant area. The study also showed that the stepped screw implant is suitable for the cortical bone modulus from 10 to 13.4 GPa, which is not necessarily as strict as the Branemark implant, for which a minimum 13.4 GPa cortical bone modulus is recommended.

scholarly journals Predicting Trabecular Bone Stiffness from Clinical Cone-Beam CT and HR-pQCT Data; an In Vitro Study Using Finite Element Analysis

PLoS ONE ◽  
2016 ◽  
Vol 11 (8) ◽  
pp. e0161101 ◽  
Author(s):  
Eva Klintström ◽  
Benjamin Klintström ◽  
Rodrigo Moreno ◽  
Torkel B. Brismar ◽  
Dieter H. Pahr ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Trabecular Bone ◽  
Cone Beam Ct ◽  
In Vitro Study ◽  
Vitro Study ◽  
Cone Beam ◽  
Element Analysis ◽  
Bone Stiffness

scholarly journals 3D Finite Element Analysis of Rotary Instruments in Root Canal Dentine with Different Elastic Moduli

2021 ◽  
Vol 11 (6) ◽  
pp. 2547 ◽  
Author(s):  
Carlo Prati ◽  
João Paulo Mendes Tribst ◽  
Amanda Maria de Oliveira Dal Piva ◽  
Alexandre Luiz Souto Borges ◽  
Maurizio Ventre ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Root Canal ◽  
Elastic Moduli ◽  
Reaction Force ◽  
Von Mises Stress ◽  
Elastic Behavior ◽  
Element Analysis ◽  
Heat Treated ◽  
Von Mises

The aim of the present investigation was to calculate the stress distribution generated in the root dentine canal during mechanical rotation of five different NiTi endodontic instruments by means of a finite element analysis (FEA). Two conventional alloy NiTi instruments F360 25/04 and F6 Skytaper 25/06, in comparison to three heat treated alloys NiTI Hyflex CM 25/04, Protaper Next 25/06 and One Curve 25/06 were considered and analyzed. The instruments’ flexibility (reaction force) and geometrical features (cross section, conicity) were previously investigated. For each instrument, dentine root canals with two different elastic moduli(18 and 42 GPa) were simulated with defined apical ratios. Ten different CAD instrument models were created and their mechanical behaviors were analyzed by a 3D-FEA. Static structural analyses were performed with a non-failure condition, since a linear elastic behavior was assumed for all components. All the instruments generated a stress area concentration in correspondence to the root canal curvature at approx. 7 mm from the apex. The maximum values were found when instruments were analyzed in the highest elastic modulus dentine canal. Strain and von Mises stress patterns showed a higher concentration in the first part of curved radius of all the instruments. Conventional Ni-Ti endodontic instruments demonstrated higher stress magnitudes, regardless of the conicity of 4% and 6%, and they showed the highest von Mises stress values in sound, as well as in mineralized dentine canals. Heat-treated endodontic instruments with higher flexibility values showed a reduced stress concentration map. Hyflex CM 25/04 displayed the lowest von Mises stress values of, respectively, 35.73 and 44.30 GPa for sound and mineralized dentine. The mechanical behavior of all rotary endodontic instruments was influenced by the different elastic moduli and by the dentine canal rigidity.

Investigating the Calibration Curves for a Two Component Cutting Tool Lathe Dynamometer Using Finite Element Analysis

2016 ◽  
Vol 24 ◽  
pp. 71-84
Author(s):  
Osezua Obehi Ibhadode ◽  
Ishaya Musa Dagwa ◽  
Akii Okonigbon Akhaehomen Ibhadode
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cutting Tool ◽  
Von Mises Stress ◽  
Equation Modeling ◽  
Element Analysis ◽  
Calibration Curves ◽  
Two Component ◽  
Applied Forces ◽  
Von Mises

Calibration curves of a multi-component dynamometer is of essence in machining operations in a lathe machine as they serve to provide values of force and stress components for cutting tool development and optimization. In this study, finite element analysis has been used to obtain the deflection and stress response of a two component cutting tool lathe dynamometer, for turning operation, when the cutting tool is subjected to cutting and thrust forces from 98.1N to 686.7N (10 to 70kg-wts), at intervals of 98.1N(10kg-wt). By obtaining the governing equation, modeling the dynamometer assembly, defining boundary conditions, generating the assembly mesh, and simulating in Inventor Professional; horizontal and vertical components of deflection by the dynamometer were read off for three different loading scenarios. For these three loading scenarios, calibration plots by experiment compared with plots obtained from simulation by finite element analysis gave accuracies of 79%, 95%, 84% and 36%, 57%, 63% for vertical and horizontal deflections respectively. Also, plots of horizontal and vertical components of Von Mises stress against applied forces were obtained.

scholarly journals Simulasi Kekuatan Mekanik Sudu Turbin Angin Horizontal Menggunakan Software Simscale

2021 ◽  
Vol 4 (2) ◽  
Author(s):  
Mubni Nazar ◽  
Anggito Pringgo Tetuko ◽  
Djuhana Djuhana
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Von Mises

Penelitian ini dilakukan untuk meningkatkan koefisien daya yang maksimal. Salah satunya dengan mengunakan kualitas sudu yang baik. Untuk mengoptimalkan fungsi turbin angin penulis menggunakan material sudu pada turbin angin dengan menggunakan Acrylonitrine Butadine Styrene (ABS). Oleh karena itu pada penelitian ini metode yang digunakan adalah metode Finite Element Analysis Simulasi yang dipilih adalah dynamic. Penelitian ini adalah pengujian kekuatan sudu turbin angin horizontal dengan variasi kecepatan angin 10 – 20 m/s ditinjau dari von mises stress dan displacement. Dari hasil simulasi kecepatan angin memiiki pengaruh terhadap distribusi stress dan displacement. Material yang digunakan masih berada di bawah batas kekuatan material, semakin besar gaya yang diberikan semakin besar nilai stress dan displacement. Pada hasil simulasi didapatkan nilai stress minimum 5.8 Pa stress maksimum 22.94 Sedangkan dalam pengujian displacement dihasilkan nilai minimum 1.27 m displacement maksimum 4.99 m.

Mechanical and Optimization Analyses for Novel Wound Composite Axial Impeller

2009 ◽  
Author(s):  
Jifeng Wang ◽  
Qubo Li ◽  
Norbert Mu¨ller
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Speed ◽  
High Performance ◽  
Low Cost ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Loading Conditions ◽  
Element Analysis ◽  
Wound Composite

A mechanical and optimal analyses procedure is developed to assess the stresses and deformations of Novel Wound Composite Axial-Impeller under loading conditions particular to centrifuge. This procedure is based on an analytical method and Finite Element Analysis (FEA, commercial software ANSYS) results. A low-cost, light-weight, high-performance, composite turbomachinery impeller from differently designed patterns will be evaluated. Such impellers can economically enable refrigeration plants using water as a refrigerant (R718). To create different complex patterns of impellers, MATLAB is used for creating the geometry of impellers, and CAD software UG is used to build three-dimensional impeller models. Available loading conditions are: radial body force due to high speed rotation about the cylindrical axis and fluid forces on each blade. Two-dimensional plane stress and three-dimensional stress finite element analysis are carried out using ANSYS to validate these analytical mechanical equations. The von Mises stress is investigated, and maximum stress and Tsai-Wu failure criteria are applied for composite material failure, and they generally show good agreement.

Investigation on stress distribution and pressure capacity of two-layer split high-pressure die based on finite element analysis

2019 ◽  
Vol 233 (14) ◽  
pp. 5048-5055
Author(s):  
Z Yi ◽  
WZ Fu ◽  
MZ Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Pressure ◽  
Stress State ◽  
Von Mises Stress ◽  
Stress Distributions ◽  
Element Analysis ◽  
Round Cylinder ◽  
Von Mises ◽  
Supporting Ring

In order to obtain a higher pressure capacity for the high-pressure die with a larger sample cavity, two types of two-layer split dies with a round cylinder and a quadrate cylinder were designed based on the conventional belt-type die. Finite element analysis was performed to investigate the stress distributions and pressure capacities of the high-pressure dies using a derived Mohr–Coulomb criterion and the von Mises criterion for the cylinder and supporting rings, respectively. As predicted by the finite element analysis results, in the two-layer split dies with a round cylinder, the stress state of the cylinder can be only slightly improved; and the von Mises stress of the first layer supporting ring can be hardly decreased. However, in the two-layer split dies with a quadrate cylinder and sample cavity, the stress state of the cylinder can be remarkably improved. Simultaneously, the von Mises stress of the supporting rings, especially for the first-layer supporting ring, can be also effectively decreased. The pressure capacities of the two-layer split dies with a round cylinder and a quadrate cylinder are 16.5% and 63.9% higher with respect to the conventional belt-type die.

Sign in / Sign up

Export Citation Format

Share Document