A Pressure Reduction to Prevent a Time-Delayed Failure in a Damaged Pipeline

2020 ◽  
Author(s):  
Andrew Cosham ◽  
Brian N. Leis ◽  
Paul Roovers ◽  
Mures Zarèa ◽  
Valerie Linton
Keyword(s):  
Full Scale ◽  
The Other ◽  
Battelle Memorial Institute ◽  
Pressure Reduction ◽  
Pipe Steels ◽  
Percent Reduction ◽  
Lower Strength ◽  
Line Pipe ◽  
Delayed Failure ◽  
Strength And Toughness

Abstract A time-delayed failure due to stress-activated creep (cold-creep) is a failure that occurs under a constant load and with no growth due corrosion, fatigue or some other environmentally assisted time-dependent degradation mechanism. A time-delayed failure is prevented by reducing the pressure. ASME B31.4 and B31.8 recommend a 20 percent reduction, to 80 percent of the pressure at the time of damage or discovery. T/PM/P/11 Management Procedure for Inspection, assessment and repair of damaged (non-leaking) steel pipelines, an internal procedure used by National Grid, specifies a 15 percent reduction. The guidance in ASME B31.4 and B31.8, and in T/PM/P/11, is directly or indirectly based on the results of tests on the long term stability of defects conducted by the Battelle Memorial Institute and British Gas Corporation in the 1960s and 70s. The line pipe steels were Grades X52 or X60, and the full-size equivalent Charpy V-notch impact energy (where reported) did not exceed 35 J. The tests indicated that the threshold for a time-delayed failure was approximately 85–95% SAPF (straightaway-pressure-to-failure). The strength and toughness of line pipe steels has significantly increased over the decades due to developments in steel-making and processing. The question then is whether an empirical threshold based on tests on lower strength and lower toughness steels is applicable to higher strength and higher toughness steels. In the Tripartite Project, the Australian Pipelines and Gas Association (APGA), the European Pipeline Research Group (EPRG) and the Pipeline Research Council International (PRCI) collaborated in conducting full-scale six step-load-hold tests on higher strength and higher toughness steels. Companion papers present the other aspects of this multi-year project. An empirical threshold for a time-delayed failure is estimated using the results of the six step-load-hold tests. That estimate is also informed by the other published small and full-scale tests (on lower strength and lower toughness steels). The Ductile Flaw Growth Model is used to infer the effect of strength and toughness on the threshold for a time-delayed failure. A 15 percent pressure reduction, to 85 percent of the pressure at the time of damage (or of the maximum pressure that has occurred since the time of damage), is considered to be sufficient to prevent a time-delayed failure due to stress-activated creep in lower and higher toughness, in lower and higher strength, and in older and newer line pipe steels.

Full-Scale Step-Load-Hold Tests on X65 and X70 Line Pipe Steels

2020 ◽  
Author(s):  
Andrew Cosham ◽  
Brian N. Leis ◽  
Mures Zarèa ◽  
Fabian Orth ◽  
Valerie Linton
Keyword(s):  
Impact Energy ◽  
Full Scale ◽  
Small Scale ◽  
Battelle Memorial Institute ◽  
Pipe Steels ◽  
Line Pipe ◽  
Delayed Failure ◽  
Hold Period ◽  
Full Scale Tests ◽  
Scale Step

Abstract A time-delayed failure due to stress-activated creep (cold-creep) will occur if the applied load is held constant at a level above the threshold. The results of small and full-scale tests on line pipe steels conducted by the Battelle Memorial Institute and the British Gas Corporation in the 1960s and 70s indicated that the (empirical) threshold for a time-delayed failure was approximately 85–95% SAPF (straight-away-pressure-to-failure). The line pipe steels were Grades X52 or X60, and the full-size equivalent Charpy V-notch impact energy (where reported) did not exceed 35 J. The strength and toughness of line pipe steels has significantly increased over the decades due to developments in steel-making and processing. The question then is whether an empirical threshold based on tests on lower strength and lower toughness steels is applicable to higher strength and higher toughness steels. A Tripartite Project was established to answer this question. The Australian Pipelines and Gas Association (APGA), the European Pipeline Research Group (EPRG) and the Pipeline Research Council International (PRCI) collaborated in conducting six full-scale step-load-hold tests on higher strength and higher toughness steels. Companion papers present the other aspects of this multi-year project. The line pipe supplied for testing is summarised below. • Identifier — Dimensions and Grade — f.s.e. Charpy V-notch impact energy at 0 C • APGA [A] — 457.0 × 9.1 mm, Grade X70M, ERW — 263 J • EPRG [E] — 1016.0 × 13.6 mm, Grade X70M, SAWL — 165 J • PRCI [P] — 609.6 × 6.4 mm, Grade X65, SAWL — 160 J Six step-load-hold tests, each with four part-through-wall defects, were conducted. Test Nos. APGA 1 and 2, and Nos. EPRG 1 and 2 were conducted at Engie, France. Test Nos. PRCI 1 and 2 were conducted at EWI, USA. The full-scale tests, and associated small-scale testing, are described and discussed. A time-delayed failure due to stress-activated creep occurred in each of the step-load-hold tests. The failures occurred during a hold-period at 93.7–104.4% SAPF, after a hold of approximately 1.0–13.9 hours. The results of the six step-load-hold tests are consistent with a threshold for a time-delayed failure of approximately 90% SAPF.

How New Vintage Line-Pipe Steel Fracture Properties Differ From Old Vintage Line-Pipe Steels

2012 ◽  
Author(s):  
G. Wilkowski ◽  
D.-J. Shim ◽  
Y. Hioe ◽  
S. Kalyanam ◽  
F. Brust
Keyword(s):  
Brittle Fracture ◽  
Fracture Behavior ◽  
Pipe Steel ◽  
Full Scale ◽  
Actual Behavior ◽  
Correction Factors ◽  
Pipe Steels ◽  
Line Pipe ◽  
Line Pipe Steel ◽  
Fracture Control

Newer vintage line-pipe steels, even for lower grades (i.e., X60 to X70) have much different fracture behavior than older line-pipe steels. These differences significantly affect the fracture control aspects for both brittle fracture and ductile fracture of new pipelines. Perhaps one of the most significant effects is with brittle fracture control for new line-pipe steels. From past work brittle fracture control was achieved through the specification of the drop-weight-tear test (DWTT) in API 5L3. With the very high Charpy energy materials that are being made today, brittle fracture will not easily initiate from the pressed notch of the standard DWTT specimen, whereas for older line-pipe steels that was the normal behavior. This behavior is now referred to as “Abnormal Fracture Appearance” (AFA). More recent work shows a more disturbing trend that one can get 100-percent shear area in the standard pressed-notch DWTT specimen, but the material is really susceptible to brittle fracture. This is a related phenomenon due to the high fracture initiation energy in the standard DWTT specimen that we call “Abnormal Fracture Behavior” (AFB). This paper discusses modified DWTT procedures and some full-scale results. The differences in the actual behavior versus the standard DWTT can be significant. Modifications to the API 5L3 test procedure are needed. The second aspect deals with empirical fracture control for unstable ductile fractures based on older line-pipe steel tests initially from tests 30-years ago. As higher-grade line-pipe steels have been developed, a few additional full-scale burst tests have shown that correction factors on the Charpy energy values are needed as the grade increases. Those correction factors from the newer burst tests were subsequently found to be related to relationship of the Charpy energy values to the DWTT energy values, where the DWTT has better similitude than the Charpy test for fracture behavior (other than the transition temperature issue noted above). Once on the upper-shelf, recent data suggest that what was once thought to be a grade correction factor may really be due to steel manufacturing process changes with time that affect even new low-grade steels. Correction factors comparable to that for X100 steels have been indicated to be needed for even X65 grade steels. Hence the past empirical equations in Codes and Standards like B31.8 will significantly under-predict the actual values needed for most new line-pipe steels.

The Misconception of Employing CVN Toughness as Key-Measure in Ductile Crack Arrest Prediction for Modern Line-Pipe Steels

2014 ◽  
Author(s):  
Alexander Völling ◽  
Christoph Kalwa ◽  
Marion Erdelen-Peppler
Keyword(s):  
Ductile Fracture ◽  
Data Base ◽  
Model Calibration ◽  
Crack Arrest ◽  
Full Scale ◽  
Small Scale ◽  
Material Strength ◽  
Original Material ◽  
Pipe Steels ◽  
Line Pipe

Since the late 1960s’ the Battelle Two-curve (BTC) model is the standard method applied in setting up design requirements with regard to the prevention of long-running ductile fracture in pipelines. It is a straightforward tool employing Charpy-V notch (CVN) toughness as key-measure for material resistance against crack propagation. On basis of pipe dimensions, material strength, and under consideration of decompression behavior of the transferred media, it enables to set up requirements for a minimum CVN toughness level to achieve crack arrest. Overall applicability of the BTC model is based on calibration of the underlying equations to a sound data-base, including both full-scale burst test results and small-scale laboratory testing data involving typical line-pipe grades at that period, i.e. up to grade X70 steels with below 100 J upper-shelf CVN toughness. Now over the last decades, mechanical behavior of line-pipe steels was improved significantly. Responding to market demands, higher grades were designed and also toughness levels were raised as outcome of R&D efforts within the steel industry. Unfortunately, stepping outside the original material data-base from BTC model calibration, this method did forfeit its reliability. At the beginning, mispredictions were mainly related to higher grade steels and elevated operating pressures. But more recent full-scale tests did reveal discrepancies in application of the BTC model also for so-called new vintage steels, i.e. grades actually being inside the original data base for model calibration but from current production routes. With regard to applicability/reliability of BTC model based predictions for crack arrest, the origin of uncertainty has particularly been traced back to the involved material toughness measure. Nowadays, it is common sense that the CVN upper-shelf toughness value inadequately describes the resistance against running ductile fracture. More recent thoughts coherently argue towards closer involving stress-strain response and plastic deformation capacities of the material. On basis of results for grades X65, X80 and X100, the general relation between ductility and toughness is discussed. Finally, an elastic-plastic fracture mechanics related analytical approach is introduced which enables to quantify the resistance against ductile fracture propagation. The objective is to provide a reliable procedure for crack arrest prediction in line-pipe steels.

Computational and experimental studies of the strength of full-scale samples of pipes with defects "metal loss" and "dent with groove"

2020 ◽  
Vol 10 (3) ◽  
pp. 226-233
Author(s):  
Dmitry A. Neganov ◽  
◽  
Victor M. Varshitsky ◽  
Andrey A. Belkin ◽  
◽  
...  
Keyword(s):  
Internal Pressure ◽  
Experimental Studies ◽  
Full Scale ◽  
The Other ◽  
Metal Loss ◽  
Calculation Methods ◽  
Reliable Operation ◽  
Sufficient Stability ◽  
Comparative Results ◽  
The Moment

The article contains the comparative results of the experimental and calculated research of the strength of a pipeline with such defects as “metal loss” and “dent with groove”. Two coils with diameter of 820 mm and the thickness of 9 mm of 19G steel were used for full-scale pipe sample production. One of the coils was intentionally damaged by machining, which resulted in “metal loss” defect, the other one was dented (by press machine) and got groove mark (by chisel). The testing of pipe samples was performed by applying static internal pressure to the moment of collapse. The calculation of deterioration pressure was carried out with the use of national and foreign methodical approaches. The calculated values of collapsing pressure for the pipe with loss of metal mainly coincided with the calculation experiment results based on Russian method and ASME B31G. In case of pipe with dent and groove the calculated value of collapsing pressure demonstrated greater coincidence with Russian method and to a lesser extent with API 579/ASME FFS-1. In whole, all calculation methods demonstrate sufficient stability of results, which provides reliable operation of pipelines with defects.

Niobium Microalloyed Line Pipe Steels: Technological Overview

2013 ◽  
Author(s):  
J. M. Gray ◽  
S. V. Subramanian
Keyword(s):  
Process Integration ◽  
Target Strength ◽  
Accelerated Cooling ◽  
Pipe Steels ◽  
Line Pipe ◽  
Steel Technology ◽  
Quantitative Understanding ◽  
Line Pipe Steel ◽  
Low Levels ◽  
Evolution Of Microstructure

A quantitative understanding of hierarchical evolution of microstructure is essential in order to design the base chemistry and optimize rolling schedules to obtain the morphological microstructure coupled with high density and dispersion of crystallographic high angle boundaries to achieve the target strength and fracture properties in higher grade line pipe steels, microalloyed with niobium. Product-process integration has been the key concept underlying the development of niobium microalloyed line pipe steel technology over the years. The development of HTP technology based on 0.1 wt % Nb and low interstitial was predicated by advances in process metallurgy to control interstitial elements to low levels (C <0.03wt% and N< 0.003wt%), sulfur to ultra-low levels (S<20ppm), as well as in product metallurgy based on advances in basic science aspects of thermo-mechanical rolling and phase transformation of pancaked austenite under accelerated cooling conditions, and toughness properties of heat affected zones in welding of niobium microalloyed line pipes. A historical perspective/technological overview of evolution of HTP for line pipe applications is the focus of this paper in order to highlight the key metallurgical concepts underlying Nb microalloying technology which have paved the way for successful development of higher grade line pipe steels over the years.

Improved Specifications Needed for Line Pipe Steels

1963 ◽  
Vol 15 (04) ◽  
pp. 370-374
Author(s):  
J.W. Squire
Keyword(s):  
Pipe Steels ◽  
Line Pipe

Influence of martensite-austenite (MA) on impact toughness of X80 line pipe steels

2016 ◽  
Vol 662 ◽  
pp. 481-491 ◽  
Author(s):  
Nazmul Huda ◽  
Abdelbaset R.H. Midawi ◽  
James Gianetto ◽  
Robert Lazor ◽  
Adrian P. Gerlich
Keyword(s):  
Impact Toughness ◽  
Pipe Steels ◽  
Line Pipe

Fatigue Crack Growth at Electrical Resistance Welding Seam of API 5L X-70 Steel Line Pipe at Varied Orientations

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Craig Taylor ◽  
Sreekanta Das ◽  
Laurie Collins ◽  
Muhammad Rashid
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Base Metal ◽  
Electrical Resistance ◽  
Weld Seam ◽  
Full Scale ◽  
Resistance Welding ◽  
Line Pipe ◽  
Full Scale Testing

Very few studies have been conducted concerning fatigue in steel line pipe and fewer using full-scale testing. Further, at the time of this study, no research on full-scale testing was available in open literature regarding fatigue behavior of line pipe with longitudinal cracks, despite being considered more critical than the line pipe with cracks oriented in the circumferential direction. In the current research work, fatigue crack growth was investigated in NPS 20, API 5L X-70 grade, electrical resistance welding (ERW) straight-seam steel line pipes in the base metal and at the weld seam for various orientations. It was found that there was no significant difference between fatigue crack growth in the base metal and at the weld seam for the tested stress ratio. Increasing the angle of inclination of the crack with respect to the weld line was found to decrease the rate of fatigue crack growth due to a decrease in the mode I stress component. Finally, it was observed that despite the difference in fatigue crack growth rates, the crack aspect ratios were nearly identical for all cracks at the same crack depth.

Girth Weld Strength Matching Effect on Tensile Strain Capacity of Grade X70 High Strain Line Pipe

2018 ◽  
Author(s):  
Hisakazu Tajika ◽  
Takahiro Sakimoto ◽  
Tsunehisa Handa ◽  
Rinsei Ikeda ◽  
Joe Kondo
Keyword(s):  
High Strain ◽  
Limit State ◽  
Full Scale ◽  
Bending Test ◽  
High Grade ◽  
Line Pipe ◽  
Bending Tests ◽  
Strain Capacity ◽  
Pipeline Project ◽  
Pipe Bending

Recently high grade pipeline project have been planned in hostile environment like landslide in mountain area, liquefaction in reclaimed land or the frost heave in Polar Regions. Geohazards bring large scale ground deformation and effect on the varied pipeline to cause large deformation. Therefore, strain capacity is important for the pipeline and strain based design is also needed to keep gas transportation project in safe. High grade steel pipe for linepipe tends to have higher yield to tensile (Y/T) ratio and it has been investigated that the lower Y/T ratio of the material improves strain capacity in buckling and tensile limit state. In onshore pipeline project, pipe usually transported in 12 or 18m each and jointed in the field. Girth weld (GW) is indispensable so strength matching of girth weld towards pipe body is important. In this study strain capacity of Grade X70 high strain pipes with size of 36″ OD and 23mm WT was investigated with two types of experiments, which are full scale pipe bending tests and curved wide plate tests. The length of the specimen of full scale bending tests were approximately 8m and girth weld was made in the middle of joint length. A fixed internal pressure was applied during the bending test. Actual pipe situation in work was simulated and both circumferential and longitudinal stress occurred in this test. Test pipes were cut and welded, GTAW in first two layer and then finished by GMAW. In one pipe, YS-TS over-matching girth weld (OVM) joint was prepared considering the pipe body grade. For the other pipe, intentionally under-matching girth weld (UDM) joint was prepared. After the girth welding, elliptical EDM notch were installed in the GW HAZ as simulated weld defect. In both pipe bending tests, the buckling occurred in the pipe body at approximately 300mm apart from the GW and after that, deformation concentrated to buckling wrinkle. Test pipe breaking locations were different in the two tests. In OVM, tensile rupture occurred in pipe body on the backside of buckling wrinkle. In UDM, tensile rupture occurred from notch in the HAZ. In CWP test, breaking location was the HAZ notch. There were significant differences in CTOD growth in HAZ notch in these tests.

Sign in / Sign up

Export Citation Format

Share Document