scholarly journals Numerical Study of Density Ratio Influence on Global Wave Shapes Before Impact

2018 ◽  
Author(s):  
Stéphane Etienne ◽  
Yves-Marie Scolan ◽  
Laurent Brosset
Keyword(s):  
Surface Tension ◽  
Free Surface ◽  
Gas Flow ◽  
Numerical Study ◽  
Mechanical Energy ◽  
Density Ratio ◽  
Free Surface Flows ◽  
Liquid Density ◽  
The Impact ◽  
Wave Shapes

The influence of the gas-to-liquid density ratio (DR) on the global wave shape before impact is studied through numerical simulations of the propagation of two different waves in a rectangular wave canal. Two different codes are used: the first one, named FSID, is a highly non-linear 2D bi-fluid potential code initially developed in the frame of SLOSHEL JIP (Kaminski et al. (2011)) to simulate incompressible inviscid free-surface flows without surface tension thanks to a desingularized technique and series of conformal mappings; the second one, named CADYF, is a bi-fluid high-fidelity front-tracking software developed by Ecole Polytechnique Montreal to simulate separated two-phase incompressible viscous flows with surface tension. The first studied wave leads to a flip-through impact while the second one leads to a large gas-pocket impact. Each condition is studied with water and three different gases with increasing densities corresponding to DR = 0.001, 0.003 and 0.005. The global wave shapes are compared a few tenths of second before the impact, before free surface instabilities triggered by the shearing gas flow have developed and also before any gas compressibility matters. Both codes give precisely the same global wave shapes. Whatever the condition studied, it is shown that DR has an influence on these global wave shapes. The trends observed from the simulations are the same as those described in Karimi et al. (2016) obtained from sloshing model tests with Single Impact Waves (SIW) in a 2D tank with a low filling level. A small part of the mechanical energy of the liquid is progressively given to the gas. The larger the DR, the larger this transfer of energy from the liquid to the gas. This explains an increasing delay of the wave front for increasing DRs.

Numerical Study of Surface Tension Effect on the Hydrodynamic Modeling of the Partially Submerged Propeller's Blade Section

2016 ◽  
Vol 32 (5) ◽  
pp. 653-664 ◽  
Author(s):  
E. Yari ◽  
H. Ghassemi
Keyword(s):  
Surface Tension ◽  
Free Surface ◽  
Volume Fraction ◽  
Numerical Study ◽  
Suction Side ◽  
Navier Stokes ◽  
Surface Tension Effect ◽  
Pressure Distributions ◽  
Blade Section ◽  
The Impact

AbstractThis article is presented the surface tension effect on the two-dimensional blade section of the partially submerged propeller (PSP). In this regard, blade is entered to the water that causes to splash the water due to the impact and free surface. Also, because of the blade's angle of attack suction side is vented by air and pressure side is wetted and gripped the water to generate thrust. The Reynolds-Averaged Navier-Stokes (RANS) method is used in order to predict the hydrodynamic flow from entering to the exit. Present paper is numerically investigated the effect of free surface and surface tension i.e. related to the Weber number. So, many numerical results are presented and discussed that are included volume fraction, ventilation zones, pressure distributions, vertical and horizontal forces at various Weber numbers.

Numerical Investigation of Focused Waves and Their Interaction With a Vertical Cylinder Using REEF3D

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Hans Bihs ◽  
Mayilvahanan Alagan Chella ◽  
Arun Kamath ◽  
Øivind Asgeir Arntsen
Keyword(s):  
Free Surface ◽  
Stokes Equations ◽  
Free Surface Flows ◽  
Surface Elevation ◽  
Numerical Wave Tank ◽  
Free Surface Elevation ◽  
Wave Tank ◽  
Numerical Wave ◽  
Focused Wave ◽  
The Impact

For the stability of offshore structures, such as offshore wind foundations, extreme wave conditions need to be taken into account. Waves from extreme events are critical from the design perspective. In a numerical wave tank, extreme waves can be modeled using focused waves. Here, linear waves are generated from a wave spectrum. The wave crests of the generated waves coincide at a preselected location and time. Focused wave generation is implemented in the numerical wave tank module of REEF3D, which has been extensively and successfully tested for various wave hydrodynamics and wave–structure interaction problems in particular and for free surface flows in general. The open-source computational fluid dynamics (CFD) code REEF3D solves the three-dimensional Navier–Stokes equations on a staggered Cartesian grid. Higher order numerical schemes are used for time and spatial discretization. For the interface capturing, the level set method is selected. In order to test the generated waves, the time series of the free surface elevation are compared with experimental benchmark cases. The numerically simulated free surface elevation shows good agreement with experimental data. In further computations, the impact of the focused waves on a vertical circular cylinder is investigated. A breaking focused wave is simulated and the associated kinematics is investigated. Free surface flow features during the interaction of nonbreaking focused waves with a cylinder and during the breaking process of a focused wave are also investigated along with the numerically captured free surface.

scholarly journals Experimental study of the wake behind a surface-piercing cylinder for a clean and contaminated free surface

2000 ◽  
Vol 402 ◽  
pp. 109-136 ◽  
Author(s):  
AMY WARNCKE LANG ◽  
MORTEZA GHARIB
Keyword(s):  
Surface Tension ◽  
Free Surface ◽  
Turbulent Flows ◽  
Cross Sections ◽  
Surface Deformation ◽  
Surface Condition ◽  
Free Surface Flows ◽  
Shear Stresses ◽  
Surface Contaminants ◽  
A New Technique

This experimental investigation into the nature of free-surface flows was to study the effects of surfactants on the wake of a surface-piercing cylinder. A better understanding of the process of vorticity generation and conversion at a free surface due to the absence or presence of surfactants has been gained. Surfactants, or surface contaminants, have the tendency to reduce the surface tension proportionally to the respective concentration at the free surface. Thus when surfactant concentration varies across a free surface, surface tension gradients occur and this results in shear stresses, thus altering the boundary condition at the free surface. A low Reynolds number wake behind a surface-piercing cylinder was chosen as the field of study, using digital particle image velocimetry (DPIV) to map the velocity and vorticity field for three orthogonal cross-sections of the flow. Reynolds numbers ranged from 350 to 460 and the Froude number was kept below 1.0. In addition, a new technique was used to simultaneously map the free surface deformation. Shadowgraph imaging of the free surface was also used to gain a better understanding of the flow. It was found that, depending on the surface condition, the connection of the shedding vortex filaments in the wake of the cylinder was greatly altered with the propensity for surface tension gradients to redirect the vorticity near the free surface to that of the surface-parallel component. This result has an impact on the understanding of turbulent flows in the vicinity of a free surface with varying surface conditions.

Numerical Simulation of Breaking Waves Using a Level Set Method

2002 ◽  
Author(s):  
Pablo Go´mez ◽  
Julio Herna´ndez ◽  
Joaqui´n Lo´pez ◽  
Fe´lix Faura
Keyword(s):  
Free Surface ◽  
Level Set Method ◽  
Level Set ◽  
Stokes Equations ◽  
Numerical Study ◽  
Operating Conditions ◽  
Breaking Wave ◽  
Level Set Function ◽  
Set Function ◽  
The Impact

A numerical study of the initial stages of wave breaking processes in shallow water is presented. The waves considered are assumed to be generated by moving a piston in a two-dimensional channel, and may appear, for example, in the injection chamber of a high-pressure die casting machine under operating conditions far from the optimal. A numerical model based on a finite-difference discretization of the Navier-Stokes equations in a Cartesian grid and a second-order approximate projection method has been developed and used to carry out the simulations. The evolution of the free surface is described using a level set method, with a reinitialization procedure of the level set function which uses a local grid refinement near the free surface. The ability of different algorithms to improve mass conservation in the reinitialization step of the level set function has been tested in a time-reversed single vortex flow. The results for the breaking wave profiles show the flow characteristics after the impact of the first plunging jet onto the wave’s forward face and during the subsequent splash-up.

A Numerical Study of Electrode Arrangements for Precise Microdrop Generation in an Electrowetting-Based Digital Microfluidic Platform

2019 ◽  
Author(s):  
Yin Guan ◽  
Baiyun Li ◽  
Mengnan Zhu ◽  
Shengjie Cheng ◽  
Jiyue Tu ◽  
...  
Keyword(s):  
Free Surface ◽  
Cell Model ◽  
Numerical Study ◽  
Digital Microfluidics ◽  
Surface Force ◽  
Viscous Force ◽  
Generation Process ◽  
Parallel Plates ◽  
Digital Microfluidic ◽  
The Impact

Abstract Owing to the wide applications in a large variety of multi-disciplinary areas, electrowetting-based digital microfluidics (DMF) has received considerable attention in the last decade. However, because of the complexity involved in the droplet generation process, the techniques and configurations for precise and controllable microdrop generation are still unclear. In this paper, a numerical study has been performed to investigate the impact of electrode arrangements on microdrop generation in an electrowetting-based DMF Platform proposed by a previously published experimental work. The governing equations for the microfluidic flow are solved by a finite volume formulation with a two-step projection method on a fixed numerical domain. The free surface of the microdrop is tracked by a coupled level-set and volume-of-fluid (CLSVOF) method, and the surface tension at the free surface is computed by the continuum surface force (CSF) scheme. A simplified viscous force scheme based on the ‘Hele-Shaw cell’ model is adopted to evaluate the viscous force exerted by the parallel plates. The generation process has been simulated with three different electrode arrangements, namely, ‘SL’, ‘SW’, and ‘SQ’. The effect of electrode arrangement on microdrop volume has been investigated. Besides, the influences of the initial microdrop location and volume on the generation process for the ‘SL’ design have been studied. The results can be used to advance microdrop generation techniques for various electrowetting-based DMF applications.

scholarly journals Experimental and Numerical Study of Free-Surface Flows in a Corrugated Pipe

Water ◽  
2018 ◽  
Vol 10 (5) ◽  
pp. 638 ◽  
Author(s):  
Francesco Calomino ◽  
Giancarlo Alfonsi ◽  
Roberto Gaudio ◽  
Antonino D’Ippolito ◽  
Agostino Lauria ◽  
...  
Keyword(s):  
Free Surface ◽  
Numerical Study ◽  
Free Surface Flows ◽  
Surface Flows

Modeling the sloshing problem in a rectangular tank with submerged incomplete baffles

2016 ◽  
Vol 26 (3/4) ◽  
pp. 722-744 ◽  
Author(s):  
Marcela A. Cruchaga ◽  
Carlos Ferrada ◽  
Nicolás Márquez ◽  
Sebastián Osses ◽  
Mario Storti ◽  
...  
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Wave Height ◽  
Numerical Study ◽  
Free Surface Flows ◽  
Numerical Results ◽  
Surface Evolution ◽  
Content Type ◽  
Near Resonance ◽  
Wave Heights

Purpose – The present work is an experimental and numerical study of a sloshing problem including baffle effects. The purpose of this paper is to assess the numerical behavior of a Lagrangian technique to track free surface flows by comparison with experiments, to report experimental data for sloshing at different conditions and to evaluate the effectiveness of baffles in limiting the wave height and the wave propagation. Design/methodology/approach – Finite element simulations performed with a fixed mesh technique able to describe the free surface evolution are contrasted with experimental data. The experiments consist of an acrylic tank of rectangular section designed to attach baffles of different sizes at different distance from the bottom. The tank is filled with water and mounted on a shake table able to move under controlled horizontal motion. The free surface evolution is measured with ultrasonic sensors. The numerical results computed for different sloshing conditions are compared with the experimental data. Findings – The reported numerical results are in general in good agreement with the experiments. In particular, wave heights and frequencies response satisfactorily compared with the experimental data for the several cases analyzed during steady state forced sloshing and free sloshing. The effectiveness of the baffles increases near resonance conditions. From the set of experiments studied, the major reduction of the wave height was obtained when larger baffles were positioned closer to the water level at rest. Practical implications – Model validation: evaluation of the effectiveness of non-massive immersed baffles during sloshing. Originality/value – The value of the present work encompass the numerical and experimental study of the effect of immersed baffles during sloshing under different imposed conditions and the comparison of numerical results with the experimental data. Also, the results shown in the present work are a contribution to the understanding of the role in the analysis of the proposed problem of some specific aspects of the geometry and the imposed motion.

Sign in / Sign up

Export Citation Format

Share Document