Mechanical Properties and Fracture Toughness of Aluminum Vessels by Friction Stir Welding

2004 ◽  
Author(s):  
Masahito Mochizuki ◽  
Masao Toyoda ◽  
Masayuki Inuzuka ◽  
Hidehito Nishida
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Crack Initiation ◽  
Base Metal ◽  
Welded Joint ◽  
Stir Zone ◽  
Crack Initiation And Propagation ◽  
Friction Stir ◽  
Fine Grained ◽  
Initiation And Propagation

Mechanical properties and fracture toughness in friction stir welded joint of vessels of structural aluminum alloy type A5083-O are investigated. Welded joint from 25 mm-thick plate is fabricated by one-side one-pass friction stir. Charpy impact energy and critical crack-tip opening displacement (CTOD) in friction stir weld are much higher than those of base metal or heat-affected zone, whereas mechanical properties such as stress-strain curve and Vickers hardness do not have a conspicuous difference. Effects of microstructure on crack initiation and propagation are studied in order to clarify the difference of fracture toughness between stir zone and base metal. Both tensile test and bending test show that the fine-grained microstructure in stir zone induces to increase ductile crack initiation and propagation resistance by analyzing fracture resistance curves and diameter of dimples in fracture surface. It is found that high fracture toughness value in stir zone is affected fine-grained microstructure by friction stirring.

Fatigue crack paths and properties in A356-T6 aluminum alloy microstructurally modified by friction stir processing under different conditions

2015 ◽  
Author(s):  
A. Tajiri ◽  
Y. Uematsu ◽  
T. Kakiuchi ◽  
Y. Suzuki
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Crack ◽  
Crack Initiation ◽  
Friction Stir Processing ◽  
Casting Defects ◽  
Processing Conditions ◽  
Tool Rotational Speed ◽  
Crack Initiation And Propagation ◽  
Friction Stir ◽  
Initiation And Propagation

A356-T6 cast aluminum alloy is a light weight structural material, but fatigue crack initiates and propagates from a casting defect leading to final fracture. Thus it is important to eliminate casting defects. In this study, friction stir processing (FSP) was applied to A356-T6, in which rotating tool with probe and shoulder was plunged into the material and travels along the longitudinal direction to induce severe plastic deformation, resulting in the modification of microstructure. Two different processing conditions with low and high tool rotational speeds were tried and subsequently fully reversed fatigue tests were performed to investigate the effect of processing conditions on the crack initiation and propagation behavior. The fatigue strengths were successfully improved by both conditions due to the elimination of casting defects. But the lower tool rotational speed could further improve fatigue strength than the higher speed. EBSD analyses revealed that the higher tool rotational speed resulted in the severer texture having detrimental effects on fatigue crack initiation and propagation resistances.

scholarly journals Microstructural Analysis of Friction Stir Butt Welded Al-Mg-Sc-Zr Alloy Heavy Gauge Sheets

Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 806 ◽  
Author(s):  
Tatiana Kalashnikova ◽  
Andrey Chumaevskii ◽  
Kirill Kalashnikov ◽  
Sergei Fortuna ◽  
Evgeny Kolubaev ◽  
...  
Keyword(s):  
Base Metal ◽  
Microstructural Analysis ◽  
Metal Flow ◽  
Sheet Thickness ◽  
Stir Zone ◽  
Layer By Layer ◽  
Friction Stir ◽  
Fine Grained ◽  
Grain Size Distributions ◽  
Zr Alloy

Friction stir welding (FSW) on a heavy gauge sheet of a hereditary fine-grained Al-Mg-Sc-Zr alloy was carried out to study the specifics of plasticized metal flow and microstructural evolution in different sections and zones of the joint. It was found that the stir zone (SZ) macrostructure may contain either a single or many nugget zones depending on the metal sheet thickness and the seam length. The effect of grain kinking in a thermomechanically affected zone (TMAZ) under pressure from the stir zone metal was discovered. The stir zone metal was fine-grained but had a microhardness lower than that of the base metal, which may be explained by the overaging effect of FSW on the Al3Sc precipitates. The tensile strength of the joint was almost equal to that of the base metal (BM). The grain size distributions were obtained in different sections below the sheet surface and away from the exit hole, which allowed us to suggest the specific adhesion-assisted layer-by layer metal transfer mechanism in FSW.

scholarly journals Enhancement in Interply Toughness of BMI Composites Using Micro-Thin Films

2021 ◽  
Vol 5 (2) ◽  
pp. 49
Author(s):  
Eldho Mathew ◽  
Sunil Chandrakant Joshi ◽  
Periyasamy Manikandan
Keyword(s):  
Thin Films ◽  
Fracture Toughness ◽  
Crack Initiation ◽  
Mixed Mode ◽  
Sliding Mode ◽  
Mode I ◽  
Crack Initiation And Propagation ◽  
Polymeric Thin Films ◽  
Initiation And Propagation ◽  
Automated Fiber Placement

Nowadays, laminated composites are widely used in the aerospace sector. All laminates have interply/interlaminar interfaces even if they are made using automated processes. The interfaces act as the areas of weaknesses and the potential crack initiation regions. Hence, any enhancement in the crack initiation and propagation resistance is always sought after. Usage of polymeric thin films is one of the promising and viable ways to achieve this. It is also easy to incorporate micro-thin films into any automation process. In the present study, different customized thin films that are compatible with Glass/BMI composites are fabricated. Fracture toughness tests in Mode I (opening mode), Mode II (sliding mode) and Mixed Mode I/II are conducted respectively using Double Cantilever Beam (DCB), End Notch Flexure (ENF) and Mixed Mode Bending (MMB) test specimens. This paper discusses the manufacturing of compatible micro-thin films. The various challenges faced during the manufacturing and incorporation of thin films are presented. The results of the various fracture toughness tests are examined. Mechanisms through which the different films help in resisting the crack initiation and propagation are deliberated and discussed. The incorporation of this technique in Automated Fiber Placement (AFP) is also discussed.

scholarly journals Crack Initiation Criteria in EBC under Thermal Stress

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 697 ◽  
Author(s):  
Kawai ◽  
Kakisawa ◽  
Kubo ◽  
Yamaguchi ◽  
Yokoi ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Thermal Stress ◽  
Crack Initiation ◽  
Interface Crack ◽  
Fem Analysis ◽  
Interface Fracture ◽  
Mechanical Reliability ◽  
Crack Initiation And Propagation ◽  
Environmental Barrier Coatings ◽  
Initiation And Propagation

For design of multi-layered environmental barrier coatings (EBCs), it is essential to assure mechanical reliability against interface crack initiation and propagation induced by thermal stress owing to a misfit of the coefficients of thermal expansion between the coating layers and SiC/SiC substrate. We conducted finite element method (FEM) analyses to evaluate energy release rate (ERR) for interface cracks and performed experiment to obtain interface fracture toughness to assess mechanical reliability of an EBC with a function of thermal barrier (T/EBC; SiC/SiAlON/mullite/Yb-silicate gradient composition layer/Yb2SiO5 with porous segment structure) on an SiC/SiC substrate under thermal stress due to cooling in fabrication process. Our FEM analysis revealed that a thinner SiAlON layer and a thicker mullite layer are most suitable to reduce ERRs for crack initiation at the SiC/SiAlON, SiAlON/mullite and mullite/Yb2Si2O7 interfaces. Interface fracture tests of the T/EBC with layer thicknesses within the proposed range exhibited fracture at the SiC/SiAlON and SiAlON/mullite interfaces. We also estimated the approximate fracture toughness for the SiC/SiAlON and SiAlON/mullite interfaces and lower limit of fracture toughness for the mullite/Yb2Si2O7 interface. Comparison between ERR and fracture toughness indicates that the fabricated T/EBC possesses sufficient mechanical reliability against interface crack initiation and propagation.

Sign in / Sign up

Export Citation Format

Share Document