Stress Analysis of SS316L Tube Die Expansion for High Pressure Gas Coolers

2020 ◽  
Author(s):  
Zijian Zhao ◽  
Abdel-Hakim Bouzid
Keyword(s):  
Residual Stress ◽  
High Pressure ◽  
Plastic Material ◽  
Research Work ◽  
Material Behavior ◽  
Isotropic Hardening ◽  
Plastic Behavior ◽  
Expansion Process ◽  
Elastic Plastic ◽  
Stress States

Abstract SS316L finned tubes are becoming very popular in high-pressure gas exchangers and particularly in CO2 cooler applications. Due to the high-pressure requirement during operation, these tubes require an accurate residual stress evaluation during the expansion process. Indeed, die expansion of SS tubes creates not only high stresses when combined with operation stresses but also micro-cracks during expansion when the expansion process is not very well controlled. This research work aims at studying the elastic-plastic behavior and estimating the residual stress states by modeling the die expansion process. The stresses and deformations of the joint are analyzed numerically using the finite element method. The expansion and contraction process is modeled considering elastic-plastic material behavior for different die sizes. The maximum longitudinal, tangential and contact stresses are evaluated to verify the critical stress state of the joint during the expansion process. The importance of the material behavior in evaluating the residual stresses using kinematic and isotropic hardening is addressed.

Simplified Equations for Predicting Secondary Stress Around Pipe’s Circumference

2013 ◽  
Author(s):  
Junkan Wang ◽  
Rajil Saraswat ◽  
Ali Mirzaee-Sisan
Keyword(s):  
Residual Stress ◽  
Plastic Material ◽  
Axial Strain ◽  
Quadratic Equation ◽  
Material Behavior ◽  
Global Maximum ◽  
Isotropic Hardening ◽  
Element Analysis ◽  
Hardening Material ◽  
Maximum Residual Stress

This paper examines the magnitude and location of the maximum residual stress induced in pipes after the process of bending, reverse-bending and straightening. Dimensional analysis is used to establish generalized equations relating the maximum residual stress magnitude and location to the pipe geometry, maximum bending curvature and pipe material’s yield stress. 64 design cases based on an analytical solution assuming elastic-perfectly-plastic material behavior have been conducted. Regression analysis has revealed that the magnitude of the maximum residual stress can be conservatively approximated by a simplified quadratic equation involving the maximum axial bending strain, whereas the location of the maximum residual stress can be approximated by a linear function based on the same. Both equations are expected to be valid and conservative for X65 and X70 grade steel pipes under global maximum axial strain between 1% and 3%. Non-linear finite element analysis based on a realistic design example with isotropic hardening material is used to validate the prediction results based on the simplified equations.

Analytical Modeling of Hydraulically Expanded Tube-to-Tubesheet Joints

2007 ◽  
Author(s):  
Nor Eddine Laghzale ◽  
Abdel-Hakim Bouzid
Keyword(s):  
Contact Pressure ◽  
Analytical Modeling ◽  
Plastic Material ◽  
Material Behavior ◽  
Plastic Behavior ◽  
Initial Contact ◽  
Expansion Process ◽  
Perfectly Plastic ◽  
Reliable Assessment ◽  
Elastic Perfectly Plastic

The loss of the initial tightness during service is one of the major causes of failure of tube-to-tubesheet joints. The initial residual contact pressure and its variation during the lifetime of the joint is among the parameters to blame. A reliable assessment of the initial contact pressure value requires accurate and rigorous modeling of the elasto-plastic behavior of the tube and the tubesheet during the expansion process. This paper deals with the development of a new analytical model used to accurately predict the residual contact pressure resulting from a hydraulic expansion process. It is based on the elastic perfectly plastic material behavior of the tube and the tubesheet and the interaction between them. The model results have been compared and validated with those of the more accurate numerical FEA models. Additional comparisons have been made with existing methods.

Effect of material's behavior on residual stress distribution in elastic–plastic beam bending: An analytical solution

2015 ◽  
Vol 231 (4) ◽  
pp. 361-372 ◽  
Author(s):  
Jalal Joudaki ◽  
Mohammad Sedighi
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stress Distribution ◽  
Residual Stress Distribution ◽  
Material Behavior ◽  
Plastic Behavior ◽  
Element Analysis ◽  
Elastic Plastic ◽  
Bending Radius ◽  
Beam Bending

A considerable residual stress distribution can be produced while bending of parts. This stress distribution depends on material behavior. In this article, residual stress distribution has been determined through the thickness in beam bending. For three different models of elastic–plastic behavior, the stress distribution and maximum residual stress are derived analytically. The residual stress is compared for three different bending radii as a case study. Also, finite element analysis has been carried out for two material properties. The results show that material behavior has little effect on stress distribution for large value of bending radius. As the bending radius decreases, difference of stress distribution increases rapidly among three plastic behaviors. Comparing the results of finite element and analytical stress distribution shows good accuracy for suggested formulations.

Fatigue Evaluation in Mixing Zones: Comparison of Different Criteria of Fatigue

2008 ◽  
Author(s):  
J. M. Stephan ◽  
C. Gourdin ◽  
J. Angles ◽  
S. Quilici ◽  
L. Jeanfaivre
Keyword(s):  
Fatigue Damage ◽  
Thermal Stresses ◽  
Plastic Material ◽  
Material Behavior ◽  
Damage Evaluation ◽  
Elastic Plastic ◽  
Different Types ◽  
Elastic Plastic Material ◽  
Fatigue Evaluation

The distribution of unsteady temperatures in the wall of the 6" FATHER mixing tee mock-up is calculated for a loading configuration: The results seem realistic even if they are not still very accurate (see paper PVP2005-71592 [11]). On this basis, thermal stresses are evaluated for elastic and elastic-plastic material behavior. Then, different types of fatigue criteria are used to evaluate the fatigue damage. The paper develops a brief description of the criteria, the corresponding fatigue damage evaluation and attempts to explain the differences.

Residual Stress Regenerated on Low Plasticity Burnished Inconel 718 Surface After Initial Turning Process

2019 ◽  
Vol 141 (12) ◽  
Author(s):  
Yang Hua ◽  
Zhanqiang Liu ◽  
Bing Wang ◽  
Jiaming Jiang
Keyword(s):  
Residual Stress ◽  
Stress Field ◽  
Analytical Model ◽  
Inconel 718 ◽  
Plastic Behavior ◽  
Residual Stress Field ◽  
Workpiece Material ◽  
Elastic Plastic ◽  
Initial Residual Stress ◽  
Low Plasticity Burnishing

Abstract Low plasticity burnishing (LPB) has been extensively employed in aero-industry to enhance fatigue performance of machined components by introducing compressive residual stress. Effects of various parameters on the residual stress field induced by low plasticity burnishing have been investigated by many researchers. However, initial residual stresses induced by machining are one of the important factors which affect the residual stress regenerated by the LPB process. The present work aims to develop an analytical model which takes into account the initial residual stress and burnishing parameters to predict residual stress field of workpiece material Inconel 718 based on Hertz contact theory and elastic–plastic theory. Initial residual stress fields were produced by turning of Inconel 718 and were measured by using X-ray diffraction technique. Two types of material constitutive models such as the linear hardening model and isotropic–kinematic model were employed to describe the elastic–plastic behavior of workpiece material Inconel 718. An analytical study was performed to analyze the effect of the initial residual stress field and burnishing parameters on residual stress induced by low plastic burnishing. The results of analytical model were verified by conducting the LPB experiments on initial turned Inconel 718. The results showed that the shape and magnitude of the residual stress field obtained with considering the effect of initial residual stress field was in good accordance with experimental measurements.

An Analytical Solution for Three-Dimensional Elliptical Elastic-Plastic Rolling Contact

2014 ◽  
Vol 658 ◽  
pp. 207-212
Author(s):  
Gabriel Popescu
Keyword(s):  
Residual Stresses ◽  
Yield Criterion ◽  
Tangential Force ◽  
Rolling Direction ◽  
Three Dimensional ◽  
Rolling Contact ◽  
Material Behavior ◽  
Hertzian Contact ◽  
Plastic Behavior ◽  
Elastic Plastic

An analytical three-dimensional elastic-plastic over-rolling solution is used to evaluate the plastic strains and residual stresses. Central to this plastic contact formulation is the incremental approach to deal with non-linear material behavior. The Prandtl-Reuss constitutive equations in conjunction with Huber-Mises-Hencky yield criterion and Ramberg-Osgood strain-hardening relationships are applied to describe the plastic behavior of common hardened bearing steel. The model was extended to include the tangential force in the rolling direction, assumed to be proportional to the hertzian contact pressure. Comparisons of three-dimensional pure rolling and rolling/sliding contact results were provided to elucidate the differences in residual stresses and residual profiles in case of kinematic and work-hardening materials.

Sign in / Sign up

Export Citation Format

Share Document