Characteristics of Dynamic Loading Obtained From Braced Piping Support Under Sinusoidal Shaking Condition

2020 ◽  
Author(s):  
Ryuya Shimazu ◽  
Ichiro Tamura ◽  
Shinichi Matsuura ◽  
Michiya Sakai ◽  
Yohei Ono
Keyword(s):  
Time History ◽  
Maximum Force ◽  
Plastic Behavior ◽  
Deformation Diagram ◽  
Restoring Force ◽  
Maximum Deformation ◽  
Elastic Plastic ◽  
Vibration Tests ◽  
Input Wave

Abstract Loads applied to structures by means of vibration can be classified into load-controlled and displacement-controlled loads. The realistic elastic-plastic behavior of structures subjected to seismic loads is not fully understood, and the classification of the load applied to structures by means of earthquakes is unclear. The failure mode differs depending on the load classification, and thus clarifying the classification of the load applied to the structure is useful for designing the structure. This study clarified the realistic load classification of structures under an elastic-plastic response. Vibration tests were conducted using sinusoidal waves as inputs, and the elastic-plastic behavior of the piping supports undergoing buckling or fatigue failure was obtained. The maximum restoring force and the maximum deformation relationship were obtained from the envelope of the time history data of the test results. In addition, it was shown that the classification of the load could be determined from the maximum force-deformation diagram, even in cases involving buckling and fatigue. In the maximum force-deformation diagram, when the change in the ratio of dynamic restoring force to static restoring force is small, a load-controlled load is applied to the structure because the restoring force of the structure follows the change in the input wave. By contrast, when the change in the ratio of dynamic response displacement to static displacement is small, a displacement-controlled load is applied to the structure because the response displacement of the structure follows the change in the input wave.

Elastic-plastic behavior of coldworked holes

1983 ◽  
Author(s):  
H. ARMEN ◽  
A. LEVY ◽  
H. EIDINOFF
Keyword(s):  
Plastic Behavior ◽  
Elastic Plastic

Nonlinear Dynamic Analysis of the Damping Frame Structure System

2012 ◽  
Vol 594-597 ◽  
pp. 886-890 ◽  
Author(s):  
Gan Hong ◽  
Mei Li ◽  
Yi Zhen Yang
Keyword(s):  
Energy Dissipation ◽  
Seismic Response ◽  
Nonlinear Dynamic ◽  
Time History ◽  
Time History Analysis ◽  
Frame Structure ◽  
Force Model ◽  
Operating Characteristics ◽  
Restoring Force ◽  
History Analysis

Abstract. In the paper, take full account of energy dissipation operating characteristics. Interlayer shear-frame structure for the analysis of the Wilson-Θmethod ELASTOPLASTIC schedule, the design of a nonlinear dynamic time history analysis procedure. On this basis, taking into account the restoring force characteristics of the energy dissipation system, the inflection point in the restoring force model treatment, to avoid a result of the calculation results of distortion due to the iterative error. A frame structure seismic response time history analysis results show that: the framework of the energy dissipation significantly lower than the seismic response of the common framework, and its role in the earthquake when more significant.

Elastic-Plastic Time History Analysis of MR Damping Structure Based on LQG Algorithm

2016 ◽  
Vol 858 ◽  
pp. 145-150
Author(s):  
Yu Liang Zhao ◽  
Zhao Dong Xu
Keyword(s):  
Optimal Control ◽  
Time History ◽  
Mr Damper ◽  
Time History Analysis ◽  
Control Force ◽  
Control Effect ◽  
Damping Force ◽  
Optimal Control Strategy ◽  
Elastic Plastic ◽  
History Analysis

This paper discussed an elastic-plastic time-history analysis on a structure with MR dampers based on member model, in which the elastoplastic member of the structure is assumed to be single component model and simulated by threefold line stiffness retrograde model. In order to obtain better control effect, Linear Quadratic Gaussian (LQG) control algorithm is used to calculate the optimal control force, and Hrovat boundary optimal control strategy is used to describe the adjustable damping force range of MR damper. The effectiveness of the MR damper based on LQG algorithm to control the response of the structure was investigated. The results from numerical simulations demonstrate that LQG algorithm can effectively improve the response of the structure against seismic excitations only with acceleration feedback.

Effect of Defect on Elastic/Plastic and Creep Behavior of Bone: A Finite Element Study

2007 ◽  
Author(s):  
A. Ajdari ◽  
P. K. Canavan ◽  
H. Nayeb-Hashemi ◽  
G. Warner
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Trabecular Bone ◽  
Fatigue Loading ◽  
Dimensional Structure ◽  
Plastic Behavior ◽  
Element Analysis ◽  
Elastic Plastic ◽  
Local Bone ◽  
Osteoporotic Vertebral Fractures

Three-dimensional structure of trabecular bone can be modeled by 2D or 3D Voronoi structure. The effect of missing cell walls on the mechanical properties of 2D honeycombs is a first step towards understanding the effect of local bone resorption due to osteoporosis. In patients with osteoporosis, bone mass is lost first by thinning and then by resorption of the trabeculae [1]. Furthermore, creep response is important to analyze in cellular solids when the temperature is high relative to the melting temperature. For trabecular bone, as body temperature (38 °C) is close to the denaturation temperature of collagen (52 °C), trabecular bone creeps [1]. Over the half of the osteoporotic vertebral fractures that occur in the elderly, are the result of the creep and fatigue loading associated with the activities of daily living [2]. The objective of this work is to understand the effect of missing walls and filled cells on elastic-plastic behavior of both regular hexagonal and non-periodic Voronoi structures using finite element analysis. The results show that the missing walls have a significant effect on overall elastic properties of the cellular structure. For both regular hexagonal and Voronoi materials, the yield strength of the structure decreased by more than 60% by introducing 10% missing walls. In contrast, the results indicate that filled cells have much less effect on the mechanical properties of both regular hexagonal and Voronoi materials.

Thermal Annealing Effect on Elastic-Plastic Behavior of Al-Si-Cu Structural Films Under Uniaxial and Biaxial Tension

2013 ◽  
Vol 22 (6) ◽  
pp. 1414-1427 ◽  
Author(s):  
Takahiro Namazu ◽  
Masayuki Fujii ◽  
Hiroki Fujii ◽  
Kei Masunishi ◽  
Yasushi Tomizawa ◽  
...  
Keyword(s):  
Thermal Annealing ◽  
Biaxial Tension ◽  
Annealing Effect ◽  
Plastic Behavior ◽  
Elastic Plastic

Load Regime Diagram of a Pipe With Cyclically Plastic Bending

2002 ◽  
Author(s):  
Yanping Yao ◽  
Ming-Wan Lu
Keyword(s):  
Axial Force ◽  
Bending Moment ◽  
Boundary Curve ◽  
Plastic Behavior ◽  
Cyclic Bending ◽  
Elastic Plastic ◽  
Linear Elastic ◽  
Load Regime ◽  
Reversed Cyclic ◽  
Cyclic Bending Moment

The criteria of piping seismic design based on linear elastic analysis has been proved to be conservative, which is mainly because the influence of plastic deformation on piping dynamic response is neglected. In the present paper, a pipe under seismic excitation is simplified as an beam with tubular cross section subjected to steady axial force and fully reversed cyclic bending moment, and the elastic-plastic behavior of the pipe is studied. Various behavior of the pipe under different combinations of axial force and cyclic bending moment is discussed and the boundary curve equations between them are obtained. Also the load regime diagram for a pipe which is formed by the boundary curve equations in the loading plane is given, from which the elastic-plastic behavior of the pipe can be determined directly.

Sign in / Sign up

Export Citation Format

Share Document