Braille display device using soft actuator

According to the situation that conditional Braille book is difficulty in publication and its amount is small. This paper puts forward a tactile display system which can transform content of common e-book to Braille information, and the blind comprehend the text by touching the Braille formed by the tactile display device. This Braille tactile display system extracts Chinese characters by OCR technology. The text recognized is segmented into word blocks according to the rule of Braille word segmentation before transforming to double-phoneme mandarin Braille. It uses dsPIC30F2010 to receive Braille signal and then controls the piezoelectric actuator array to output corresponding displacement.

Download Full-text

Performance study of RTV-2 Silicone Rubber Material For Soft Actuator by Experimental and Numerical methods: The Effect of Inflation Pressure and Wall Thickness

International Journal of Automotive and Mechanical Engineering ◽

10.15282/ijame.17.1.2020.01.0556 ◽

2020 ◽

Vol 17 (1) ◽

pp. 7524-7532 ◽

Cited By ~ 1

Author(s):

Deepak D. ◽

Nitesh Kumar ◽

Shreyas P. Shetty ◽

Saurabh Jain ◽

Manoj Bhat

Keyword(s):

Numerical Methods ◽

Wall Thickness ◽

Silicone Rubber ◽

Inflation Pressure ◽

Performance Study ◽

Rubber Material ◽

Soft Actuator ◽

Alternative Materials ◽

Load Carrying ◽

Influential Parameters

The expensive nature of currently used materials in the soft robotic industry demands the consideration of alternative materials for fabrication. This work investigates the performance of RTV-2 grade silicone rubber for fabrication of a soft actuator. Initially, a cylindrical actuator is fabricated using this material and its performance is experimentally assessed for different pressures. Further, parametric variations of the effect of wall thickness and inflation pressure are studied by numerical methods. Results show that, both wall thickness and inflation pressure are influential parameters which affect the elongation behaviour of the actuator. Thin (1.5 mm) sectioned actuators produced 76.97% more elongation compared to thick sectioned, but the stress induced is 89.61 % higher. Whereas, the thick sectioned actuator (6 mm) showed a higher load transmitting capability. With change in wall thickness from 1.5 mm to 6 mm, the elongation is reduced by 76.97 %, 38.35 %, 21.05 % and 11.43 % at pressure 100 kPa, 75 kPa, 50 kPa and 25 kPa respectively. The induced stress is also found reduced by 89.61 %, 86.66 %, 84.46 % and 68.68 % at these pressures. The average load carrying capacity of the actuator is found to be directly proportional to its wall thickness and inflation pressure.

Download Full-text

Actuation and dynamic mechanical characteristics of a core free flat dielectric electro-active polymer soft actuator

JOURNAL OF MECHANICAL ENGINEERING AND SCIENCES ◽

10.15282/jmes.14.4.2020.08.0582 ◽

2020 ◽

Vol 14 (4) ◽

pp. 7396-7404

Author(s):

Abdul Malek Abdul Wahab ◽

Emiliano Rustighi ◽

Zainudin A.

Keyword(s):

Theoretical Model ◽

Resonance Frequency ◽

Dynamic Testing ◽

Experimental Results ◽

Percentage Error ◽

Initial Tension ◽

Average Percentage ◽

Soft Actuator ◽

Average Percentage Error ◽

Mechanical Dynamics

Various complex shapes of dielectric electro-active polymer (DEAP) actuator have been promoted for several types of applications. In this study, the actuation and mechanical dynamics characteristics of a new core free flat DEAP soft actuator were investigated. This actuator was developed by Danfoss PolyPower. DC voltage of up to 2000 V was supplied for identifying the actuation characteristics of the actuator and compare with the existing formula. The operational frequency of the actuator was determined by dynamic testing. Then, the soft actuator has been modelled as a uniform bar rigidly fixed at one end and attached to mass at another end. Results from the theoretical model were compared with the experimental results. It was found that the deformation of the current actuator was quadratic proportional to the voltage supplied. It was found that experimental results and theory were not in good agreement for low and high voltage with average percentage error are 104% and 20.7%, respectively. The resonance frequency of the actuator was near 14 Hz. Mass of load added, inhomogeneity and initial tension significantly affected the resonance frequency of the soft actuator. The experimental results were consistent with the theoretical model at zero load. However, due to inhomogeneity, the frequency response function’s plot underlines a poor prediction where the theoretical calculation was far from experimental results as values of load increasing with the average percentage error 15.7%. Hence, it shows the proposed analytical procedure not suitable to provide accurate natural frequency for the DEAP soft actuator.

Download Full-text

Estimating OLED Display Device Lifetime from pixel and screen brightness and its application

Color and Imaging Conference ◽

10.2352/issn.2169-2629.2019.27.60 ◽

2019 ◽

Vol 2019 (1) ◽

pp. 331-338 ◽

Cited By ~ 1

Author(s):

Jérémie Gerhardt ◽

Michael E. Miller ◽

Hyunjin Yoo ◽

Tara Akhavan

Keyword(s):

Image Processing ◽

Power Consumption ◽

Model Parameters ◽

Display Device ◽

Image Processing Algorithm ◽

Pixel Value ◽

Device Lifetime ◽

The Impact ◽

Oled Display

In this paper we discuss a model to estimate the power consumption and lifetime (LT) of an OLED display based on its pixel value and the brightness setting of the screen (scbr). This model is used to illustrate the effect of OLED aging on display color characteristics. Model parameters are based on power consumption measurement of a given display for a number of pixel and scbr combinations. OLED LT is often given for the most stressful display operating situation, i.e. white image at maximum scbr, but having the ability to predict the LT for other configurations can be meaningful to estimate the impact and quality of new image processing algorithms. After explaining our model we present a use case to illustrate how we use it to evaluate the impact of an image processing algorithm for brightness adaptation.

Download Full-text

High-cycle-life and high-loading copolymer network with potential application as a soft actuator

Materials & Design ◽

10.1016/j.matdes.2019.108010 ◽

2019 ◽

Vol 182 ◽

pp. 108010 ◽

Cited By ~ 6

Author(s):

Hafeez Ur Rehman ◽

Yujie Chen ◽

Mikael S. Hedenqvist ◽

Radan Pathan ◽

Hezhou Liu ◽

...

Keyword(s):

Potential Application ◽

Cycle Life ◽

High Loading ◽

Soft Actuator ◽

Copolymer Network

Download Full-text

Sensuator: A Hybrid Sensor–Actuator Approach to Soft Robotic Proprioception Using Recurrent Neural Networks

Actuators ◽

10.3390/act10020030 ◽

2021 ◽

Vol 10 (2) ◽

pp. 30

Author(s):

Pornthep Preechayasomboon ◽

Eric Rombokas

Keyword(s):

Neural Networks ◽

Recurrent Neural Networks ◽

Linear Models ◽

Open Loop ◽

Proof Of Concept ◽

State Estimator ◽

Loop Control ◽

Practical Applications ◽

Soft Actuator ◽

The Cost

Soft robotic actuators are now being used in practical applications; however, they are often limited to open-loop control that relies on the inherent compliance of the actuator. Achieving human-like manipulation and grasping with soft robotic actuators requires at least some form of sensing, which often comes at the cost of complex fabrication and purposefully built sensor structures. In this paper, we utilize the actuating fluid itself as a sensing medium to achieve high-fidelity proprioception in a soft actuator. As our sensors are somewhat unstructured, their readings are difficult to interpret using linear models. We therefore present a proof of concept of a method for deriving the pose of the soft actuator using recurrent neural networks. We present the experimental setup and our learned state estimator to show that our method is viable for achieving proprioception and is also robust to common sensor failures.

Download Full-text