Structure and Mechanical Characteristics of a Laminated Ti3AlC2 MAX Phase-Based Composite Material Prepared by a Free Self-Propagating High-Temperature Synthesis Compression Method

2021 ◽  
Vol 57 (9) ◽  
pp. 937-941
Author(s):  
A. D. Prokopets ◽  
P. M. Bazhin ◽  
A. S. Konstantinov ◽  
A. P. Chizhikov ◽  
P. A. Stolin
Keyword(s):  
Composite Material ◽  
High Temperature ◽  
Mechanical Characteristics ◽  
Max Phase ◽  
Compression Method ◽  
Temperature Synthesis ◽  
High Temperature Synthesis

Microstructure and Mechanical Properties of Mg-Based Composites Reinforced with TiB2 Particles

2014 ◽  
Vol 900 ◽  
pp. 141-145 ◽  
Author(s):  
Can Feng Fang ◽  
Guang Xu Liu ◽  
Ling Gang Meng ◽  
Xing Guo Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
High Temperature ◽  
The Self ◽  
Al Alloy ◽  
Temperature Synthesis ◽  
Microstructure And Mechanical Properties ◽  
High Temperature Synthesis

The effects of in-situ TiB2 particle fabricated from Al-Ti-B system via the self-propagating high-temperature synthesis (SHS) reaction technology on microstructure and mechanical properties of Mg-Sn-Zn-Al alloy were investigated. The results indicate that the size of the Mg2Sn and α-Mg+Mg32(Al,Zn)49 phase becomes coarser with the increasing content of Al-Ti-B preform, meanwhile the amount of eutectic α-Mg+Mg32(Al,Zn)49 phase increases too. The addition of Al-Ti-B is favorable toward promoting the strength of composites, but deteriorates elongation. The resulting as-extruded composite material with 4 wt.% Al-Ti-B preform exhibits good overall mechanical properties with an ultimate tensile strength of 291 MPa and an elongation over 2 %.

High-temperature synthesis of cast materials based on Nb2AlC MAX phase

2019 ◽  
Vol 45 (2) ◽  
pp. 2689-2691 ◽  
Author(s):  
Pavel A. Miloserdov ◽  
Vladimir A. Gorshkov ◽  
Ivan D. Kovalev ◽  
Dmitrii Yu. Kovalev
Keyword(s):  
High Temperature ◽  
Max Phase ◽  
Temperature Synthesis ◽  
High Temperature Synthesis

Self-propagating high-temperature synthesis of composite material TiB2-Fe

2004 ◽  
Vol 39 (11) ◽  
pp. 3723-3732 ◽  
Author(s):  
O. K. Lepakova ◽  
L. G. Raskolenko ◽  
Yu. M. Maksimov
Keyword(s):  
Composite Material ◽  
High Temperature ◽  
Temperature Synthesis ◽  
High Temperature Synthesis

High-temperature synthesis of a cast material with a maximum content of the MAX phase Cr2AlC

2017 ◽  
Vol 53 (3) ◽  
pp. 271-277 ◽  
Author(s):  
V. A. Gorshkov ◽  
P. A. Miloserdov ◽  
M. A. Luginina ◽  
N. V. Sachkova ◽  
A. F. Belikova
Keyword(s):  
High Temperature ◽  
Max Phase ◽  
Temperature Synthesis ◽  
Cast Material ◽  
High Temperature Synthesis ◽  
Maximum Content

Obtaining of doped composite material Al—Cu—Mn—TiC with enhanced tribological properties

2020 ◽  
pp. 278-282
Author(s):  
A.R. Luts ◽  
A.P. Amosov ◽  
E.I. Latukhin ◽  
A.D. Rybakov ◽  
S.V. Shigin
Keyword(s):  
Composite Material ◽  
High Temperature ◽  
Titanium Carbide ◽  
Tribological Properties ◽  
Heating Temperature ◽  
Synthesis Method ◽  
Matrix Alloy ◽  
The Self ◽  
Temperature Synthesis ◽  
High Temperature Synthesis

The results of tribological characteristics of alumomatric composite material Al — 5 % Cu — 2 % Mn — 10 % TiC obtained by the self-propagating high-temperature synthesis method are presented. It is shown that in comparison with technical aluminum and matrix alloy, signifi cantly lower indicators of the coeffi cient of friction, wear and heating temperature characterize composite material, reinforced with nano- and ultrafi ne particles of titanium carbide.

Self-propagating high-temperature synthesis of Ti3AlC2 MAX phase from mechanically-activated Ti/Al/graphite powder mixture

2018 ◽  
Vol 44 (8) ◽  
pp. 9671-9678 ◽  
Author(s):  
Maryam Akhlaghi ◽  
Seyed Ali Tayebifard ◽  
Esmaeil Salahi ◽  
Mehdi Shahedi Asl ◽  
Gert Schmidt
Keyword(s):  
High Temperature ◽  
Powder Mixture ◽  
Graphite Powder ◽  
Max Phase ◽  
Temperature Synthesis ◽  
High Temperature Synthesis
Sign in / Sign up

Export Citation Format

Share Document