The effect of temperature on the stress-strain behavior of composites based on high-density polyethylene and rubber particles

2008 ◽  
Vol 50 (5-6) ◽  
pp. 105-110
Author(s):  
O. A. Serenko ◽  
I. V. Tyun’kin ◽  
G. P. Goncharuk ◽  
E. S. Obolonkova ◽  
A. V. Efimov ◽  
...  
Keyword(s):  
High Density Polyethylene ◽  
High Density ◽  
Effect Of Temperature ◽  
Stress Strain ◽  
Strain Behavior ◽  
Rubber Particles

High density polyethylene/hydrogenated oligo(cyclopentadiene) blends: Tensile stress-strain behavior

1995 ◽  
Vol 33 (12) ◽  
pp. 1723-1730 ◽  
Author(s):  
S. Cimmino ◽  
E. Di Pace ◽  
E. Martuscelli ◽  
C. Silvestre ◽  
L. C. Mendes ◽  
...  
Keyword(s):  
Tensile Stress ◽  
High Density Polyethylene ◽  
High Density ◽  
Stress Strain ◽  
Strain Behavior

scholarly journals MECHANICAL CHARACTERIZATION OF PA 12 AND HDPE PIPES BEFORE AND AFTER AGING IN WATER AT TWO DIFFERENT TEMPERATURES

2021 ◽  
Vol 9 (1) ◽  
pp. 248-256
Author(s):  
J.A. dos Santos ◽  
R.C. Tucunduva ◽  
J.R.M. D’Almeida
Keyword(s):  
High Density Polyethylene ◽  
Mechanical Performance ◽  
High Density ◽  
Effect Of Temperature ◽  
Polyamide 12 ◽  
Polyethylene Pipes ◽  
Before And After ◽  
Different Temperatures ◽  
Deterioration Process ◽  
Combined Action

Polymer pipes are being widely used by many industrial segments. Although not affected by corrosion, the mechanical performance of these pipes can be reduced due to exposure to temperature, UV radiation and by contact with various fluids. Depending on the deterioration process, embrittlement or plasticization may occur, and the service life of the pipe can be severely reduced. In this work, the combined action of temperature and water upon the mechanical performance of polyamide 12 and high-density polyethylene pipes is evaluated. Destructive and non-destructive techniques were used and the performance of both materials was compared. Both polymers were platicized by the effect of water. However, for high density polyethylene the effect of temperature was more relevant than for polyamide. This behavior was attributed to the dependence of the free volume with the markedly different glass transition temperature of the polymers and the temperatures of testing.

scholarly journals Effect of Temperature on Pyrolysis Oil Using High-Density Polyethylene and Polyethylene Terephthalate Sources From Mobile Pyrolysis Plant

2020 ◽  
Vol 8 ◽  
Author(s):  
Ruktai Prurapark ◽  
Kittwat Owjaraen ◽  
Bordin Saengphrom ◽  
Inpitcha Limthongtip ◽  
Nopparat Tongam
Keyword(s):  
Polyethylene Terephthalate ◽  
High Density Polyethylene ◽  
Main Product ◽  
Carbon Number ◽  
High Density ◽  
Raw Material ◽  
Effect Of Temperature ◽  
Pyrolysis Oil ◽  
Boiling Points ◽  
And Performance

This research aims to study the effect of temperature, collecting time, and condensers on properties of pyrolysis oil. The research was done be analyzing viscosity, density, proportion of pyrolysis products and performance of each condenser towers for the pyrolysis of high-density polyethylene (HDPE) and polyethylene terephthalate (PET) in the mobile pyrolysis plant. Results showed that the main product of HDPE resin was liquid, and the main product of PET resin was solid. Since the pyrolysis of PET results in mostly solid which blocked up the pipe, the analysis of pyrolysis oil would be from the use of HDPE as a raw material. The pyrolysis of HDPE resin in the amount of 100 kg at 400, 425, and 450°C produced the amount of oil 22.5, 27, and 40.5 L, respectively. The study found that 450°C was the temperature that gives the highest amount of pyrolysis oil in the experiment. The viscosity was in the range of 3.287–4.850 cSt. The density was in the range of 0.668–0.740 kg/L. The viscosity and density were increased according to three factors: high pyrolysis temperature, number of condensers and longer sampling time. From the distillation at temperatures below 65, 65–170, 170–250, and above 250°C, all refined products in each temperature range had the carbon number according to their boiling points. The distillation of pyrolysis oil in this experiment provided high amount of kerosene, followed by gasoline and diesel.

Effect of Temperature and Catalyst Loading on Product Yield in Catalytic Cracking of High Density Polyethylene (HDPE)

2014 ◽  
Vol 49 (6) ◽  
pp. 508-516 ◽  
Author(s):  
Behrooz Roozbehani ◽  
Bagher Anvaripour ◽  
Zahra Maghareh Esfahan ◽  
Mojtaba Mirdrikvand ◽  
Saeedeh Imani Moqadam
Keyword(s):  
Catalytic Cracking ◽  
High Density Polyethylene ◽  
Product Yield ◽  
High Density ◽  
Effect Of Temperature ◽  
Catalyst Loading

Viscoplastic Constitutive Equation of High-Density Polyethylene

2007 ◽  
Vol 340-341 ◽  
pp. 1097-1102 ◽  
Author(s):  
Yukio Sanomura ◽  
Mamoru Mizuno
Keyword(s):  
Constitutive Equation ◽  
Strain Rate ◽  
High Density Polyethylene ◽  
Kinematic Hardening ◽  
Constant Strain Rate ◽  
Strain Curve ◽  
High Density ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Creep Theory

A viscoplastic constitutive equation based on the kinematic hardening creep theory of Malinin-Khadjinsky and the nonlinear kinematic hardening rule of Armstrong-Frederick is formulated to describe the inelastic behavior of high-density polyethylene under various loading. The gentle progress of back stress by the introduction of loading surface in the viscoplastic strain space and smaller material constant under unloading can be expressed. Material constants are identified by various stress-strain curves under compression at constant strain rate and creep curves under compression at constant stress. The viscoplastic model can describe stress-strain curve under compression with change in strain rate and shear stress-strain curve including unloading. The model can qualitatively describe stress-strain curves under compression with changed strain rate including unloading, but it is quantitatively insufficient.

Sign in / Sign up

Export Citation Format

Share Document