Static and dynamic tests of timber shear walls fastened with nails and wood adhesive

1991 ◽  
Vol 18 (5) ◽  
pp. 749-755 ◽  
Author(s):  
A. Filiatrault ◽  
R. O. Foschi
Keyword(s):  
Shear Walls ◽  
Base Plate ◽  
Wood Adhesive ◽  
Adhesive Joints ◽  
Dynamic Tests ◽  
Seismic Behaviour ◽  
Timber Construction ◽  
Static And Dynamic Tests ◽  
Timber Shear Walls ◽  
Adhesive Capacity

This paper presents an experimental investigation into the seismic behaviour of timber shear walls fastened with nails alone or with nails in combination with wood adhesive. The responses of both types of shear walls were determined under slow, quasi-static racking loads and also under dynamic, earthquake-induced conditions. The experimental results showed that the introduction of the adhesive makes shear walls much stronger but also more brittle than conventional nailed walls. It was observed that shear walls incorporating nails and adhesive behaved almost linearly to failure. To obtain the most out of the adhesive capacity, however, the wood framing should be designed with special attention to the connections between framing members and the anchoring of the wall's base plate. These details control the capacity of the frame to sustain the loads induced by the stiffer adhesive joints. Key words: adhesive, earthquake, tests, timber construction, shear walls, wood.

Static and dynamic analysis of timber shear walls

1990 ◽  
Vol 17 (4) ◽  
pp. 643-651 ◽  
Author(s):  
A. Filiatrault
Keyword(s):  
Dynamic Equilibrium ◽  
Load Capacity ◽  
Shear Walls ◽  
Lateral Stiffness ◽  
Analysis Model ◽  
Equilibrium Equations ◽  
Seismic Behaviour ◽  
Nonlinear Load ◽  
Static And Dynamic Analysis ◽  
Timber Shear Walls

Light-frame wood structures have evolved in recent years to the point where their earthquake resistance is now questionable. Shear walls are commonly used to provide lateral stiffness and strength in wood buildings. Therefore, accurate predictions of the seismic behaviour of timber shear walls are necessary in order to evaluate the safety of existing timber buildings and improve design practice. This paper develops and validates a simple structural analysis model to predict the behaviour of timber shear walls under lateral static loads and earthquake excitations. The model is restricted to two-dimensional shear walls with arbitrary geometry. The nonlinear load –slip characteristics of the fasteners are used in a displacement-based energy formulation to yield the static and dynamic equilibrium equations. The model is embedded in a shear wall analysis program (SWAP) developed for microcomputer applications. The predictions of the model are compared with full-scale racking and shake table tests. The ability of the model to accurately predict the lateral stiffness, the ultimate lateral load capacity, and the complete earthquake response of timber shear walls is clearly demonstrated. Key words: dynamics, earthquakes, seismic response, timber construction, walls, wood.

Lateral performance of timber shear walls reinforced by prestressed diagonal cross bars

2018 ◽  
Vol 42 (2) ◽  
pp. 233-243
Author(s):  
HONGLIANG ZUO ◽  
Y LI ◽  
Jing DI ◽  
NAN GUO
Keyword(s):  
Shear Walls ◽  
Timber Shear Walls

scholarly journals Lateral resistance of mass timber shear wall connected by withdrawal-type connectors

2021 ◽  
Vol 67 (1) ◽  
Author(s):  
Sung-Jun Pang ◽  
Kyung-Sun Ahn ◽  
Seog Goo Kang ◽  
Jung-Kwon Oh
Keyword(s):  
Experimental Data ◽  
Seismic Design ◽  
Shear Walls ◽  
Shear Wall ◽  
Vertical Load ◽  
Lateral Resistance ◽  
Kinematic Models ◽  
Mass Timber ◽  
Timber Shear Walls ◽  
Timber Shear Wall

AbstractIn this study, the lateral resistances of mass timber shear walls were investigated for seismic design. The lateral resistances were predicted by kinematic models with mechanical properties of connectors, and compared with experimental data. Four out of 7 shear wall specimens consisted of a single Ply-lam panel and withdrawal-type connectors. Three out of 7 shear wall specimens consisted of two panels made by dividing a single panel in half. The divided panels were connected by 2 or 4 connectors like a single panel before being divided. The applied vertical load was 0, 24, or 120 kN, and the number of connectors for connecting the Ply-lam wall-to-floor was 2 or 4. As a result, the tested data were 6.3 to 52.7% higher than the predicted value by kinematic models, and it means that the lateral resistance can be designed by the behavior of the connector, and the prediction will be safe. The effects of wall-to-wall connectors, wall-to-floor connectors and vertical loads on the shear wall were analyzed with the experimental data.

The effect of the indenter elasticity on the Hertzian fracture of brittle materials

1973 ◽  
Vol 334 (1596) ◽  
pp. 95-117 ◽  
Keyword(s):  
Fracture Stress ◽  
Opposite Effect ◽  
Test Material ◽  
Test Surface ◽  
Dynamic Tests ◽  
Frictional Forces ◽  
Consistent Increase ◽  
Static And Dynamic Tests ◽  
Ring Crack ◽  
Ring Cracks

A spherical indenter loaded statically or dynamically into contact with the surface of a brittle material produces a well-defined ring crack. This phenomenon, when interpreted by the Hertz theory of elastic contact, provides a convenient test for the strength of the material. If the elastic modulus of the indenter is different from that of the test material, e. g. a steel indenter in contact with a glass surface, frictional forces are brought into play at the interface which modify the Hertz distribution of contact stress. This effect has been examined both theo­retically and experimentally. An indenter which is more rigid than the test surface is shown to lead to an apparent increase in fracture strength of the material, a less rigid indenter has the opposite effect. Static and dynamic tests of plate glass showed a consistent increase in apparent fracture stress of about 50 % using spherical steel indenters compared with glass indenters. This increase agrees well with the influence of friction upon the Hertzian stress calculated theoretically. The average radius of the ring cracks produced by steel indenters was observed to be greater than that produced by glass indenters, an effect of friction also predicted by the theory. Secondary ring cracks of smaller radius have frequently been observed during unloading of a steel indenter. These were not found when a glass indenter was used and an explanation is suggested in terms of the frictional effect which arises from a difference in elasticity between the indenter and the test surface.

Evaluation Method of U-Bolt Energy Absorption

2009 ◽  
Author(s):  
Eiji Shirai ◽  
Tetsuya Zaitsu ◽  
Kazutoyo Ikeda ◽  
Toshiaki Yoshii ◽  
Masami Kondo ◽  
...  
Keyword(s):  
Energy Absorption ◽  
Evaluation Method ◽  
Design Procedure ◽  
Piping System ◽  
Design Technique ◽  
Dynamic Tests ◽  
Key Issues ◽  
Static And Dynamic Tests ◽  
Force Displacement ◽  
Rigid Design

At domestic PWR plants in Japan, one of the major key issues is earthquake-proof safety [1–3]. Recently, a design procedure using energy absorption, not conventional rigid design, was authorized according to revised review guidelines for aseismic design (JEAC4601). Therefore, we focused on the design technique that utilizes energy absorption effects to reduce the seismic responses of the piping system with U-Bolt, by the static and dynamic tests of simplified piping model supported by U-Bolt. The force-displacement characteristics and a fatigue diagram were obtained by the tests.

Inspection and Model Experiment of a Damaged Arch Bridge

2007 ◽  
Vol 340-341 ◽  
pp. 223-228
Author(s):  
Ying Fang Fan ◽  
Zhi Qiang Hu ◽  
Jing Zhou
Keyword(s):  
Model Experiment ◽  
Dynamic Test ◽  
Dynamic Responses ◽  
Dynamic Tests ◽  
Arch Bridge ◽  
Mechanical Responses ◽  
Organic Glasses ◽  
Bridge Model ◽  
Static And Dynamic Tests ◽  
Good Agreement

The structural behavior of an old six-span reinforced concrete arch bridge, which has been in service for about 40 years, is investigated. Field monitoring (inclusive of test of material property, static and dynamic test of the bridge) was conducted, static and dynamic responses of the bridge are obtained. Based on the primitive bridge, a scaled one-span bridge model was fabricated by organic-glasses. Both the static and dynamic tests were executed on the bridge model in the laboratory. Since the arch rib is the crucial member for the arch bridge, 7 notches were cut on both arch ribs of the bridge model to simulate different damages of the arch rib. Mechanical responses of the bridge with different damages on the arch ribs were achieved. FEM analyses were preformed on the bridge as well. Numerical results show good agreement with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document