ANALYSIS OF THE MATERIAL REMOVAL RATE IN MAGNETIC ABRASIVE FINISHING OF THIN FILM COATED PYREX GLASS

2017 ◽  
Vol 24 (Supp01) ◽  
pp. 1850004
Author(s):  
HEE HWAN LEE ◽  
SEOUNG HWAN LEE
Keyword(s):  
Process Monitoring ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Measurement Data ◽  
Surface Measurement ◽  
Time Interval ◽  
Magnetic Abrasive Finishing ◽  
Afm Indentation ◽  
Abrasive Finishing

The material removal rate (MRR) during precision finishing/polishing is a key factor, which dictates the process performance. Moreover, the MRR or wear rate is closely related to the material/part reliability. For nanoscale patterning and/or planarization on nano-order thickness coatings, the prediction and in-process monitoring of the MRR is necessary, because the process is not characterizable due to size effects and material property/process condition variations as a result of the coating/substrate interactions. The purpose of this research was to develop a practical methodology for the prediction and in-process monitoring of MRR during nanoscale finishing of coated surfaces. Using a specially designed magnetic abrasive finishing (MAF) and acoustic emission (AE) monitoring setup, experiments were carried out on indium-zinc-oxide (IZO) coated Pyrex glasses. After a given polishing time interval, AFM indentation was conducted for each workpiece sample to measure the adhesion force variations of the coating layers (IZO), which are directly related to the MRR changes. The force variation and AE monitoring data were compared to the MRR calculated form the surface measurement (Nanoview) results. The experimental results demonstrate strong correlations between AFM indentation and MRR measurement data. In addition, the monitored AE signals show sensitivity of the material structure variations of the coating layer, as the polishing progresses.

Effect of Lubricant Volume and Working Gap on the Surface Roughness and Material Removal Rate in Magnetic Abrasive Finishing

2010 ◽  
Vol 297-301 ◽  
pp. 390-395
Author(s):  
Mehrdad Vahdati ◽  
E. Sadeghinia ◽  
Ali Shokuhfar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Work Piece ◽  
Magnetic Abrasive Finishing ◽  
Complex Curves ◽  
Abrasive Finishing ◽  
Technology Industries ◽  
High Technology Industries

Technological requirements urges high technology industries using materials with advanced properties. Although it is compulsory using these materials due to their advantages, some of them should be tolerated because of their weak machining and mechanical properties. Attempts for qualitative machining of complex curves on many work pieces may result in the advent of new finishing techniques. One of the most newly introduced techniques is Magnetic Abrasive Finishing, MAF. In this paper a study on the effects of tool and work piece gap, and lubricant volume, on the roughness and material removal rate have been studied. The results show that setting the working gap to 3 mm and the lubricant volume to 0.7 ml, yields a change in surface roughness (Ra), and the material removal (MR) will gain its best result.

Parametric Optimization of Magnetic Abrasive Finishing Using Adhesive Magnetic Abrasive Particles

2019 ◽  
Vol 7 (2) ◽  
pp. 34-47
Author(s):  
Palwinder Singh ◽  
Lakhvir Singh ◽  
Arishu Kaushik
Keyword(s):  
Surface Finish ◽  
Medical Equipment ◽  
Material Removal ◽  
Parametric Optimization ◽  
Removal Rate ◽  
Improvement Rate ◽  
Magnetic Abrasive Finishing ◽  
Abrasive Particles ◽  
Abrasive Finishing ◽  
Depth Analysis

A very precise surface finish is desirable in manufacturing semiconductors, medical equipment, and aerospace parts. The examinations on magnetic abrasive finishing (MAF) processes are being done for the modern industry. This newly developed process is serving the industry to achieve the desired level of precision and surface finish. This research represents the MAF of aluminum pipes using adhesive magnetic abrasive particles. The different process parameters were optimized using the Response Surface Methodology (RSM) method to gain an in-depth analysis of surface roughness in terms of roughness improvement rate (RIR), and material removal rate (MRR). The achieved maximum RIR and MRR was 81.49% and 2.74mg/min, respectively. The finished workpieces were microscopically investigated by scanning electron microscopy (SEM) to further study the mechanism of MAF process.

Material Removal Mechanism in Vibration-Assisted Magnetic Abrasive Finishing

2008 ◽  
Vol 53-54 ◽  
pp. 57-63 ◽  
Author(s):  
Shao Hui Yin ◽  
Yu Wang ◽  
Takeo Shinmura ◽  
Yong Jian Zhu ◽  
Feng Jun Chen
Keyword(s):  
Material Removal ◽  
Removal Rate ◽  
Removal Mechanism ◽  
Material Removal Mechanism ◽  
Magnetic Abrasive Finishing ◽  
Finishing Process ◽  
Abrasive Finishing ◽  
Vibration Assistance ◽  
Series Of Experiments ◽  
Working Distance

This paper proposed a viewpoint to explain why vibration assistance may increase material removal rate (MRR) in vibration-assisted magnetic abrasive finishing process. A series of experiments on vibration-assisted finishing have been carried out. On the basis of these experiments, the finishing characteristics are represented summarily. It was shown that the increase in material rate is mainly due to an increase in material removal per unit working distance.

scholarly journals Improving the process performance of magnetic abrasive finishing of SS304 material using multi-objective artificial bee colony algorithm

2020 ◽  
Vol 41 (1) ◽  
pp. 34-49
Author(s):  
Sandip B. Gunjal ◽  
Padmakar J. Pawar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Artificial Bee Colony Algorithm ◽  
Artificial Bee Colony ◽  
Removal Rate ◽  
Multi Objective Optimization ◽  
Multi Objective ◽  
Bee Colony ◽  
Abrasive Finishing

Magnetic abrasive finishing is a super finishing process in which the magnetic field is applied in the finishing area and the material is removed from the workpiece by magnetic abrasive particles in the form of microchips. The performance of this process is decided by its two important quality characteristics, material removal rate and surface roughness. Significant process variables affecting these two characteristics are rotational speed of tool, working gap, weight of abrasive, and feed rate. However, material removal rate and surface roughness being conflicting in nature, a compromise has to be made between these two objective to improve the overall performance of the process. Hence, a multi-objective optimization using an artificial bee colony algorithm coupled with response surface methodology for mathematical modeling is attempted in this work. The set of Pareto-optimal solutions obtained by multi-objective optimization offers a ready reference to process planners to decide appropriate process parameters for a particular scenario.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

Performance Analysis of Trihexyltetradecylphosphonium Chloride Ionic Fluid under MQL Condition in Hard turning

2020 ◽  
Vol 17 (1) ◽  
pp. 7629-7647
Author(s):  
A. Pandey ◽  
R. Kumar ◽  
A. K. Sahoo ◽  
A. Paul ◽  
A. Panda
Keyword(s):  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Coconut Oil ◽  
Chip Morphology ◽  
Weight Fraction ◽  
Cutting Fluid ◽  
Depth Of Cut

The current research presents an overall performance-based analysis of Trihexyltetradecylphosphonium Chloride [[CH3(CH2)5]P(Cl)(CH2)13CH3] ionic fluid mixed with organic coconut oil (OCO) during turning of hardened D2 steel. The application of cutting fluid on the cutting interface was performed through Minimum Quantity Lubrication (MQL) approach keeping an eye on the detrimental consequences of conventional flood cooling. PVD coated (TiN/TiCN/TiN) cermet tool was employed in the current experimental work. Taguchi’s L9 orthogonal array and TOPSIS are executed to analysis the influences, significance and optimum parameter settings for predefined process parameters. The prime objective of the current work is to analyze the influence of OCO based Trihexyltetradecylphosphonium Chloride ionic fluid on flank wear, surface roughness, material removal rate, and chip morphology. Better quality of finish (Ra = 0.2 to 1.82 µm) was found with 1% weight fraction but it is not sufficient to control the wear growth. Abrasion, chipping, groove wear, and catastrophic tool tip breakage are recognized as foremost tool failure mechanisms. The significance of responses have been studied with the help of probability plots, main effect plots, contour plots, and surface plots and the correlation between the input and output parameters have been analyzed using regression model. Feed rate and depth of cut are equally influenced (48.98%) the surface finish while cutting speed attributed the strongest influence (90.1%). The material removal rate is strongly prejudiced by cutting speed (69.39 %) followed by feed rate (28.94%) whereas chip reduction coefficient is strongly influenced through the depth of cut (63.4%) succeeded by feed (28.8%). TOPSIS significantly optimized the responses with 67.1 % gain in closeness coefficient.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

Optimization of Cutting Parameters in Milling Process Using Genetic Algorithm and ANOVA (March 2020)

2020 ◽  
Vol 38 (10A) ◽  
pp. 1489-1503
Author(s):  
Marwa Q. Ibraheem
Keyword(s):  
Genetic Algorithm ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Optimal Value ◽  
Optimization Of Cutting Parameters

In this present work use a genetic algorithm for the selection of cutting conditions in milling operation such as cutting speed, feed and depth of cut to investigate the optimal value and the effects of it on the material removal rate and tool wear. The material selected for this work was Ti-6Al-4V Alloy using H13A carbide as a cutting tool. Two objective functions have been adopted gives minimum tool wear and maximum material removal rate that is simultaneously optimized. Finally, it does conclude from the results that the optimal value of cutting speed is (1992.601m/min), depth of cut is (1.55mm) and feed is (148.203mm/rev) for the present work.

Sign in / Sign up

Export Citation Format

Share Document