scholarly journals SIZE EFFECT OF WELDED THIN-WALLED TUBULAR JOINTS

2007 ◽  
Vol 07 (01) ◽  
pp. 101-127 ◽  
Author(s):  
FIDELIS RUTENDO MASHIRI ◽  
XIAO-LING ZHAO ◽  
MANFRED A. HIRT ◽  
ALAIN NUSSBAUMER
Keyword(s):  
Size Effect ◽  
Wall Thickness ◽  
Hot Spot ◽  
Fatigue Behavior ◽  
T Joints ◽  
Hot Spot Stress ◽  
Tubular Joints ◽  
Thin Walled Tube ◽  
Simple Extrapolation ◽  
Thin Walled

This paper clarifies the terminologies used to describe the size effect on fatigue behavior of welded joints. It summarizes the existing research on size effect in the perspective of newly defined terminologies. It identifies knowledge gaps in designing tubular joints using the hot spot stress method, i.e. thin-walled tubular joints with wall thickness less than 4 mm and thick-walled tubular joints with wall thickness larger than 50 mm, or diameter to thickness ratio less than 24. It is the thin-walled tubular joints that are addressed in this paper. It is found that thin-walled tube-plate T-joints do not follow the conventional trend: the thinner the section is, the higher the fatigue life. It is also found that simple extrapolation of existing fatigue design curves may result in unsafe design of thin-walled tube–tube T-joints. The effect of chord stiffness on fatigue behavior of thin-walled tubular T-joints is also discussed.

Fatigue of Tubular Joints: Hot Spot Stress Method Revisited

2012 ◽  
Vol 134 (3) ◽  
Author(s):  
Pingsha Dong ◽  
Jeong K. Hong
Keyword(s):  
Hot Spot ◽  
Life Assessment ◽  
Structural Stress ◽  
T Joints ◽  
Hot Spot Stress ◽  
Tubular Joints ◽  
Fatigue Design ◽  
Fatigue Data ◽  
Section Viii ◽  
Remaining Life Assessment

A series of well-known tubular joints tested in UKSORP II have been re-evaluated using the mesh-insensitive structural stress method as a part of the on-going Battelle Structural Stress JIP efforts. In this report, the structural stress based analysis procedure is first presented for applications in tubular joints varying from simple T joints, double T Joints, YT joints with overlap, and K joints with various internal stiffening configurations. The structural stress based SCFs are then compared with those obtained using traditional surface extrapolation based hot spot stress methods. Their abilities in effectively correlating the fatigue data collected from these tubular joints are demonstrated. These tests are also compared with the T curve typically used for fatigue design of tubular joints as well as the structural stress based master S-N curve adopted by ASME Section VIII Div 2. Finally, some of the implications on fracture mechanics based remaining life assessment for tubular joints are discussed in light of the results obtained in this investigation.

Study on the Hot Spot Stress Distribution at Multi-Planar Tubular KK Joints Under Axial Loads

2011 ◽  
Author(s):  
Jingxia Yue ◽  
Jin Gan ◽  
Weiguo Wu ◽  
Shihong Zhai ◽  
Yanhua Yang
Keyword(s):  
Finite Element ◽  
Hot Spot ◽  
Fe Analysis ◽  
Axial Loads ◽  
T Joints ◽  
Hot Spot Stress ◽  
Essential Information ◽  
Tubular Joints ◽  
Jack Up ◽  
Initial Prediction

The Hot Spot Stress (HSS) distribution around welded tubular joints in truss legs is essential information for the fatigue assessment of jack-up platforms. Both Finite Element (FE) analysis and model test were carried out on a multi-planar tubular KK joints under asymmetric axial loads in our research. The study shows that the HSS distribution around welded joints is different from common K or T joints, and the maximum HSS appears between crown and saddle on the chord surface at the chord-brace intersection. Moreover, some sensitive factors which influence the locations of the maximum HSS were investigated by FEA in this paper. The analysis results are useful for the optimal structure designing and crack initial prediction of the offshore jack-up platforms legs.

Fatigue of Tubular Joints: Hot Spot Stress Method Revisited

2008 ◽  
Author(s):  
Pingsha Dong ◽  
Jeong K. Hong
Keyword(s):  
Hot Spot ◽  
Life Assessment ◽  
Structural Stress ◽  
T Joints ◽  
Hot Spot Stress ◽  
Tubular Joints ◽  
Fatigue Design ◽  
Fatigue Data ◽  
Section Viii ◽  
Remaining Life Assessment

A series of well-known tubular joints tested in UKSORP II have been re-evaluated using the mesh-insensitive structural stress method as a part of the on-going Battelle Structural Stress JIP efforts. In this report, the structural stress based analysis procedure is first presented for applications in tubular joints varying from simple T joints, double T Joints, YT joints with overlap and K joints with various internal stiffening configurations. The structural stress based SCFs are then compared with those obtained using traditional surface extrapolation based hot spot stress methods. Their abilities in effectively correlating the fatigue data collected from these tubular joints are demonstrated. These tests are also compared with the T curve typically used for fatigue design of tubular joints as well as the structural stress based master S-N curve adopted by ASME Section VIII Div 2. Finally, some of the implications on fracture mechanics based remaining life assessment for tubular joints are discussed in light of the results obtained in this investigation.

scholarly journals Evidence for Stacking Faults in Multiaxial Strained Alpha-Brass

1983 ◽  
Vol 27 ◽  
pp. 363-368
Author(s):  
R. B. Roof
Keyword(s):  
Wall Thickness ◽  
External Surface ◽  
Large Strain ◽  
Stacking Faults ◽  
Multiaxial Loading ◽  
Tube Surface ◽  
Line Broadening ◽  
X Ray ◽  
Thin Walled Tube ◽  
Thin Walled

As part of a program studying the effects of large strain deformations resulting from multiaxial loading to a variety of materials, a thin walled tube (0.46” O.D. x 0.02” wall thickness) of 70-30 Brass was subjected to strain deformation in the following directions 1) along the tube axis, εz = 0.3393; 2) circumferential around the tube surface, εθ = -0.0121; 3) perpendicular to the wall thickness, εR = 0.3514. This report describes the results of an x-ray examination of the external surface of the tube by the line broadening technique.

scholarly journals Fatigue Strength Curve for Tubular Joints of Offshore Structures under Dynamic Loading

Dynamics ◽  
2021 ◽  
Vol 1 (1) ◽  
pp. 125-133
Author(s):  
Sudath C. Siriwardane ◽  
Nirosha D. Adasooriya ◽  
Dimitrios Pavlou
Keyword(s):  
Fatigue Strength ◽  
Hot Spot ◽  
Offshore Structures ◽  
Hot Spot Stress ◽  
Tubular Joints ◽  
Jacket Structures ◽  
Strength Curve ◽  
Tubular Joint ◽  
Stress Concentration Factors

Offshore structures are subjected to dynamic environmental loads (wave and wind loads). A stress-life fatigue strength curve is proposed for tubular joints which are in the splash zone area of offshore jacket structures. The Det Norske Veritas (DNV) offshore structures standards given design T-curve in the air is modified with the environment-dependent parameters to obtain this fatigue strength curve. Validity of the curve is done by comparing fatigue lives given by the proposed curve with experimental fatigue lives of tubular joints tested in seawater under different loading conditions. The fatigue assessment of a case study tubular joint is performed using the proposed curve. Nominal stress ranges of the members, which are connected to the joint, are obtained by dynamic analysis of the jacket structure. Stress concentration factors are utilized with the nominal stresses to obtain the hot spot stress ranges. Fatigue lives are calculated and compared with the conventional approach. Hence the applicability and significance of the proposed fatigue strength curve are discussed.

Automated Identification of Critical Tubular Joints of Offshore Jacket Structure by Deterministic Fatigue Analysis

2017 ◽  
Author(s):  
Shrikarpagam Dhandapani
Keyword(s):  
Fatigue Life ◽  
Fatigue Damage ◽  
Hot Spot ◽  
Offshore Structures ◽  
Fatigue Analysis ◽  
Optimized Design ◽  
Base Shear ◽  
Hot Spot Stress ◽  
Environmental Loads ◽  
Tubular Joints

Fatigue occurs in structures due to the stresses from cyclic environmental loads. Offshore environmental loads being highly cyclic and recurring in nature, fatigue analysis with high degree of accuracy is required for reliable and optimized design of offshore structures. The main aim of this paper is to automate the process of identification of fatigue critical tubular joints of an offshore jacket structure using deterministic fatigue analysis with emphasis on the Hot Spot Stress Range (HSSR), an important measure in estimating fatigue damage, calculated using three different approaches for each tubular joint. The first approach determines HSSR at the time of maximum base shear of the jacket, the second, by calculating the difference between maximum and minimum Hot Spot Stress (HSS) and the third, at all time-instants of the wave cycle. Thus fatigue damage and fatigue life of the tubular joints are estimated using the highest HSSR value and the joints with lower fatigue life are identified as fatigue sensitive joints. This ensures effective identification of critical tubular joints of the offshore jacket structure which needs detailed investigation or redesign for fatigue. The deterministic approach discussed in this paper is applicable to large jackets which contains more number of tubular joints where sophisticated fatigue assessment at the preliminary stage is computationally intensive and manual identification of fatigue critical joints is laborious.

An Approach for Analysis of Bulged Profile and Thickness Distribution of Tube in Free Hydro-Bulging Process

2012 ◽  
Vol 499 ◽  
pp. 127-131
Author(s):  
Xiao Feng Liu ◽  
Lian Fa Yang ◽  
Yu Xian Zhang
Keyword(s):  
Mathematical Model ◽  
Plastic Deformation ◽  
Finite Element ◽  
Wall Thickness ◽  
Deformation Behavior ◽  
Thickness Distribution ◽  
Plastic Deformation Behavior ◽  
Thin Walled Tube ◽  
Thin Walled ◽  
Tubular Components

Tubular components are widely used in the areas of automotive and aerospace industries due to their excellent properties. A mathematical model considering the bulged region as a parabola curve is proposed to examine the plastic deformation behavior of a thin-walled tube during the free hydro-bulged process. The finite element simulations of the free hydro-bulging process are carried out to verify the approach indirectly. The results indicate that the model is accurate and acceptable to figure out the circumferential radius, wall thickness and axial radius of the bulged profile.

Sign in / Sign up

Export Citation Format

Share Document