A Ring Silencer Design for Reducing Noise of Axial Fan

2003 ◽  
Vol 03 (03) ◽  
pp. L259-L264
Author(s):  
Jian-Da Wu ◽  
Mingsian R. Bai
Keyword(s):  
Helmholtz Resonator ◽  
Boundary Region ◽  
Acoustic Analogy ◽  
Axial Fan ◽  
Noise Sources ◽  
Fan Noise ◽  
Fluctuating Pressure ◽  
Axial Fans ◽  
Fan Blade ◽  
Broadband Frequency

In this paper, a ring silencer design for reducing the noise of axial fans is presented. The noise sources on axial fans are usually caused by the fluctuating pressure distribution on the surface of fan blade. Most of the sources are near the trailing edge of blades or boundary region of blades. The ideation of proposed design is based on the principle of Helmholtz resonator for reducing the noise around the fan. The electro-acoustic analogy of this design is presented and simply discussed. Experimental measurement is carried out to evaluate the proposed design for reducing the axial fan noise. The result of experiment indicated that the ring silencer achieved 17 dB in blade passing frequency and 10 dB in other broadband frequency of power spectrum level.

Effect of Rotor-Stator Configuration in the Generation of Vortical Scales and Wake Mixing in Single Stage Axial Fans: Part II — Assessment of Vortex Sound Sources

2013 ◽  
Author(s):  
Mónica Galdo Vega ◽  
Jesus Manuel Fernandez Oro ◽  
Katia María Argüelles Díaz ◽  
Carlos Santolaria Morros
Keyword(s):  
Deep Understanding ◽  
Operating Conditions ◽  
Axial Fan ◽  
Noise Sources ◽  
Sound Sources ◽  
Time Resolved ◽  
Vortex Sound ◽  
Starting Point ◽  
Axial Fans ◽  
The Impact

This second part is devoted to the identification of vortex sound sources in low-speed turbomachinery. As a starting point, the time-resolved evolution of the vortical motions associated to the wake shear layers (reported in the first part of the present study) is employed to obtain vorticity distributions in both blade-to-blade and traverse locations throughout the axial fan stage. Following, the Powell analogy for generation of vortex sound is revisited to obtain the noise sources in the nearfield region of the fan. Both numerical and experimental databases presented previously are now post-processed to achieve a deep understanding of the aeroacoustic behavior of the vortical scales present in the flow. A LES simulation at midspan, using a 2.5D scheme, allows an accurate description of the turn-out time of the shedding vortices, within high-density meshes in the blades and vanes passages, and a correct modeling of the dynamics of turbulence. Besides, thermal anemometry has been employed with a two-wire probe to measure the planar flow in the midspan sections of the fan. Statistical procedures and signal conditioning of velocity traces have confirmed experimentally the unsteady flow patterns devised in the numerical model. The comparison of the rotor-stator and the stator-rotor configurations provides the influence of the wake mixing and the nucleation of turbulent spots in the distribution of the Powell source terms. Moreover, the relation between the turbomachine configuration and the generation of vortex sound can be established, including the impact of the operating conditions and the contributions of the interaction mechanisms.

Axial Fan Blade Tone Cancellation Using Optimally Tuned Quarter Wavelength Resonators

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Lee Gorny ◽  
Gary H. Koopmann
Keyword(s):  
Sound Field ◽  
Test Facility ◽  
Secondary Source ◽  
Axial Fan ◽  
Ducted Fan ◽  
Quarter Wavelength ◽  
Centrifugal Fans ◽  
Line Theory ◽  
Axial Fans ◽  
Fan Blade

Fan noise challenges noise control engineers in developing products ranging in scale from small ventilation systems to large turbomachines. The dominant noise source in many axial fans is the tonal noise due to rotor/stator interactions at the fundamental blade passing frequency. Flow-excited resonators have been used in the past for minimizing blade tone sound pressure levels (SPLs) generated by centrifugal fans through means of secondary source cancellation. The focus of this research is to extend that cancellation method to axial fans by attaching flow-driven quarter wavelength resonators fitted with optimal mouth perforations around the perimeter of the fan’s shroud. A ducted-fan test facility was developed to measure upstream and downstream noise radiated from a test fan. Resonators were mounted at specific locations around the fan’s shroud to obtain reductions in blade tone SPLs in both flow directions. They were driven into resonance via the unsteady pressure from the passing blades. An analytical model using transmission line theory was developed and validated experimentally to characterize the resonator’s behavior under various flow conditions and mouth geometries. This model was used to predict the resonator’s potential for reducing in-duct blade tones for specific flows and mouth perforation patterns. In a series of experiments to obtain the optimal resonator mouth perforations, it was observed that upstream and downstream SPL attenuations require different placement of the resonator mouth relative to the blade of the fan. With a single tuned resonator it was demonstrated that the fundamental blade tone SPLs can be reduced by as much as 20 dB in either the upstream or the downstream duct but not in both directions simultaneously. This behavior results when combining the resonator’s monopolelike sound field with the dipolelike sound field of the fan’s blades. Further studies are underway to extend the above method to higher pressure fans operating at speeds that generate higher order duct modes.

Development and Application of Fan Noise Prediction Method to Axial and Centrifugal Fan

2002 ◽  
Author(s):  
Duck-Joo Lee ◽  
Wan-Ho Jeon ◽  
Ki-Hoon Chung
Keyword(s):  
Flow Field ◽  
Free Field ◽  
Sound Field ◽  
Solid Boundary ◽  
Centrifugal Fan ◽  
Acoustic Analogy ◽  
Axial Fan ◽  
Fan Noise ◽  
Scattering Effect ◽  
Numerical Predictions

Numerical predictions of fan noise have not been studied extensively. This is due to the scattering effect of the fan casing, duct and the difficulty in obtaining aerodynamic acoustic source. New method to predict the fan noise and performance is developed and used to calculate various fan noise problems. A vortex method is used to model the fan and to calculate the flow field. Acoustic pressures are obtained from the unsteady force fluctuations of the blades using an acoustic analogy. But the acoustic analogy can be applied only in the free field in general. In order to consider the solid boundary effects of the casing, the newly developed Kirchhoff-Helmholtz BEM (Boundary Element Method) is introduced. With the above-mentioned method, the flow field and sound field of centrifugal and axial fan were calculated. Reasonable results are obtained not only for the peak frequencies but also for the amplitudes of the tonal sound. Also, in the predicted sound field, we can see the scattering effect of duct and casing.

scholarly journals Strength Analysis of a Ducted Axial Fan Blade

2018 ◽  
Vol 9 (4) ◽  
pp. 85-100
Author(s):  
Marek ROŚKOWICZ ◽  
Ryszard CHACHURSKI ◽  
Sławomir TKACZUK ◽  
Piotr LESZCZYŃSKI ◽  
Maciej MAJCHER ◽  
...  
Keyword(s):  
Stress Distribution ◽  
Numerical Calculations ◽  
Strength Analysis ◽  
Axial Fan ◽  
Optical Scanner ◽  
Geometrical Features ◽  
Simplifying Assumptions ◽  
Axial Fans ◽  
Fan Blade ◽  
And Performance

This paper presents a numerical strength analysis of a ducted axial fan blade. Ducted axial fans are a large group of fluid-flow machines. The analysis was designed to determine the causes of cyclic failures of a ventilation unit. The paper presents a reverse engineering approach to the mapping of the fan blade’s geometrical features. The geometrical features were mapped by triangulation from the scanning images produced by a 3D optical scanner. These were followed by simplifying assumptions on which the numerical calculations were based. The numerical calculations were carried out at the operating rotational speeds of the ducted axial fan’s rotor. The course of the numerical calculations is described, and their results are also presented herein. The results are represented on colour maps of stress distribution for selected structural elements of the fan blade. The stress distribution at a blade cross-section was compared to CT scans of the fractures of failed rotor blade airfoils. Final conclusions were developed which show that the design engineering process of fans should feature optimisation of the fan’s efficiency, including the strength and performance parameters, which should include the service life of the fan.

Combined Aerodynamic and Phased Array Microphone Studies on Basic Models of Low-Speed Axial Fan Blade Sections

2018 ◽  
Author(s):  
Esztella Balla ◽  
János Vad
Keyword(s):  
Reynolds Number ◽  
Phased Array ◽  
High Efficiency ◽  
Low Reynolds Number ◽  
Low Noise ◽  
Axial Fan ◽  
Noise Sources ◽  
Low Speed ◽  
Axial Fans ◽  
Low Reynolds

The paper presents comparative aerodynamic and aeroacoustic studies on basic models of blade sections of low-speed, low-Reynolds-number axial fans. The wind tunnel experiments incorporated representative cambered plate and airfoil blade profiles. The aerodynamic measurements revealed that, for low Reynolds numbers, cambered plate blade sections may perform aerodynamically better than airfoil sections. A phased array microphone system, combined with a dipole beamforming and spatial filtering technique, offered a potential for localizing the noise sources in both streamwise and transversal direction. The acoustic studies focused on the profile vortex shedding noise. The results were qualitatively evaluated and compared with the semi-empirical noise prediction model developed by Brooks, Pope, and Marcolini. The measurements are considered as preparation of a dataset contributing to the background for designing high-efficiency, low-noise axial fans operating at low Reynolds number.

Numerical Study on the Passive Control of the Aeroelastic Response in Large Axial Fans

2016 ◽  
Author(s):  
A. Castorrini ◽  
A. Corsini ◽  
A. G. Sheard ◽  
F. Rispoli
Keyword(s):  
Passive Control ◽  
Numerical Study ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Axial Fan ◽  
Strongly Coupled ◽  
Dimensional Approximation ◽  
Axial Fans ◽  
Fan Blade ◽  
And Performance

The morphing geometry concept finds interesting applications in load reduction and performance increasing for wings and rotor blades in off-design conditions. Here we report a numerical study on the effect that a passive morphing system (made by an elastic-low stiffness surface) has on the sectional load and flowfield, when it is applied to the trailing edge of an axial fan. We obtain the results extracting the section of the fan blade and test it in the 2D cascade, with and without the elastic device, in different operating conditions. Keeping in mind the two-dimensional approximation, it will be possible to observe how the tested device could reduce the load in off-design and high angle of attack conditions, while the same solution could introduce vibrations in design conditions. All the simulations imply the solution of the fluid-structure interaction between the incompressible, turbulent flow and the elastic structure. This solution is obtained using a finite element based, strongly coupled solver, applied to the periodic 2D domain of the section in the cascade.

scholarly journals Investigations on noise sources on a contra-rotating axial fan with different modifications

2019 ◽  
Vol 111 ◽  
pp. 02076 ◽  
Author(s):  
Ralph Krause ◽  
Christian Friebe ◽  
Michael Kerscher ◽  
Christof Puhle
Keyword(s):  
Axial Fan ◽  
Noise Sources ◽  
Trailing Edge ◽  
Sound Sources ◽  
Rotating Blades ◽  
First Results ◽  
Fan Blade ◽  
Future Work ◽  
Different Sources ◽  
Beamforming Algorithm

An Acoustic Camera was applied to examine modifications of fan blade designs regarding their noise emissions. A so-called rotational beamforming algorithm allows for the detection of sound sources on the rotating blades by using a virtual rotation of the microphones. Depending upon the frequency different sources could be localized. Both the leading and the trailing edge were modified. This paper shows the performed modifications and tests with the Acoustic Camera. It also presents first results and gives an outlook on future work.

Morphing of Reversible Axial Fan Blade: A FSI-FEM Study

2021 ◽  
Author(s):  
Valerio F. Barnabei ◽  
Alessio Castorrini ◽  
Alessandro Corsini ◽  
Franco Rispoli
Keyword(s):  
Research Effort ◽  
Elastic Solid ◽  
Navier Stokes ◽  
Design Solution ◽  
Axial Fan ◽  
Navier Stokes Equation ◽  
Linear Elastic ◽  
Axial Fans ◽  
Fan Blade ◽  
Dynamics Simulations

Abstract Reversible axial fans are widely used in industrial and tunnel ventilation systems, and a lot of research effort is spent in the design process of the blades shape and blades profile. The target is to achieve reasonable performances in both flow directions, but those are still below the levels of the corresponding non-reversible geometries. In this paper, an alternative design solution for reversible axial fan is presented by adopting flexible blades instead of the rigid ones. Such design, inspired by the boat sails, could allow the blade to change its shape by passively adapting to the flow field, from a symmetrical blade profile to a not symmetric one, and thus adapting the curvature to the flow condition. In the paper, a series of alternative materials and material distributions are analysed and compared. The analysis is conducted by performing Fluid-Structure Interaction simulations using stabilized Finite Elements formulations for both the fluid and the structure dynamics. Simulations are performed using the in-house built software FEMpar, which implements the Residual Based Variational MultiScale to model the Navier-Stokes equation, the Total Lagrangian formulation for the non-linear elastic solid and the Solid Extension Moving Mesh Technique to move the fluid mesh.

Computation of Turbulent Flows and Aero-Acoustics From an Axial Fan

2002 ◽  
Author(s):  
Il-Sung Bae ◽  
Hooi-Joong Kim ◽  
Seungbae Lee
Keyword(s):  
Turbulent Flows ◽  
Dipole Source ◽  
Spanwise Direction ◽  
Far Field ◽  
Axial Fan ◽  
Noise Sources ◽  
Lift Forces ◽  
Fan Blade ◽  
Drag And Lift ◽  
Field Noise

LES formulation was applied to simulate the flow fields around rotating fan blades tested by DLR. The turbulent flows around fan blade rotating with 500 RPM were simulated and the far-field noise was exactly computed by using the Ffowcs Williams and Hawkings equation with an inclusion of quadrupole source formulation. Variations of lift forces and deviation angles in the spanwise direction were analyzed to correlate flow parameters with acoustics parameters and identify noise sources. The dipole noise computed at the far-field by computed drag and lift forces was in good agreement with experimental data and the dipole source was also found to be the major contributor to overall far-field noise from unsteady calculation.

Sign in / Sign up

Export Citation Format

Share Document